FIELDMANN FDW 201650-E Cordless High-pressure Cleaner User Manual

FIELDMANN FDW 201650-E Cordless High-pressure Cleaner User Manual

IMPORTANT SAFETY TIPS

Never point the high-pressure nozzle at people or animals.
Never drink alcohol or use drugs while operating the pressure cleaner.
Never operate the pressure cleaner while standing in water.
Never touch the electrical plug with wet hands.
Never let electrical connections rest in water.
Never operate pressure cleaner without the water turned on.
Never use hot water with this pressure cleaner.

IMPORTANT SAFETY PRECAUTIONS

WARNING! When using this product, basic precautions should always be followed, including the following:

1. Read all instructions before using the product. Save all safety instructions.
2. Do not operate the pressure cleaner when fatigued or under the influence of alcohol or drugs.
3. Risk of injection or injury — do not direct the high pressure water stream at any people or animals.
4. Do not allow children to operate the pressure cleaner at any time.
5. To reduce the risk of injury, close supervision is necessary when the pressure cleaner is used near children.
6. Know how to stop the unit and reduce pressure immediately. Be completely familiar with the controls.
7. Stay alert — always be aware of where you are directing the high pressure spray
8. Keep cleaning area clear of all people.
9. Keep good footing and balance at all times — do not overreach or stand on an unstable support.
10. The work area should have adequate drainage to reduce the possibility of a fall due to slippery surfaces.
11. Follow the maintenance instructions specified in the manual.
12. To reduce the risk of electrocution, keep all connections dry and off the ground. Do not touch plug with wet hands.

GENERAL SAFETY PRECAUTIONS

1. Intended for outdoor household use only.
2. High-pressure hose can develop leaks from wear, abuse, kinking etc. Do not use a damaged hose.
3. Do not use the pressure cleaner in areas near combustible materials, combustible fumes, or dust
4. Some chemicals or detergents may be harmful if inhaled or ingested causing severe injury. Use a respirator or mask whenever there is a chance that vapors may be inhaled. Read all instructions included with the mask so you are certain the mask will provide the necessary protection against inhaling harmful vapors.
5. Before starting the pressure cleaner in cold weather, check all of the parts of the equipment and be sure that ice has not formed. Do not store the unit anywhere that the temperature will fall below 0 °C (32 °F).
6. DO NOT MAKE ANY MODIFICATIONS TO ANY OF THE COMPONENTS! Units with broken or missing parts, or without the protective housing or covers should NEVER be operated
7. Keep the high-pressure hose connected to the pressure cleaner and the spray gun while the system is pressurized. Disconnecting the hose while the unit is pressurized is dangerous, and may cause injury.
8. Do not leave the pressure cleaner unattended while the power switch is ON.
9. Keep water spray away from electrical wiring or fatal electric shock may result.

SYMBOLS

Labels on your tools and in the manual may display symbols. They provide important information about the product or instructions for its use.

Warning! Never point the gun at people, animals, body parts, power sources or any electrical appliances.
The appliance is not intended for connection to a drinking water supply.
Please read the instructions
Protection Class II.
This product has been designed in compliance with approved standards.
Electrical appliances are not to be thrown in the household waste.
Please use ear protection.
Always wear safety glasses with side shields and, if necessary, a full face shield when using this product.
Acoustic power level.

SERVICING OF A DOUBLE-INSULATED APPLIANCE

In a double-insulated product, two systems of insulation are provided instead of grounding. No means of grounding is provided on a double-insulated product, nor should a means for grounding be added to the product Servicing a double- insulated product requires extreme care and knowledge of the system, and should be done only by qualified service personnel. Replacement parts for a double-insulated product must be identical to the parts they replace. A double-insulated product is marked with the words “DOUBLE INSULATION” or “DOUBLE INSULATED”.

This symbol may also be marked on the product.

USE OF EXTENSION CORDS

Use of an extension cord with this product is NOT RECOMMENDED. If you must use an extension cord, use only extension cords that are intended for outdoor use. These cords are identified by a marking “ACCEPTABLE FOR USE WITH OUTDOOR APPLIANCES, STORE INDOORS WHILE NOT IN USE.” Use only extension cords having an electrical rating not less than the rating of the product. Examine extension cord before use. DO NOT USE DAMAGED EXTENSION CORDS! Do not pull on cord to disconnect from receptacle, always disconnect by pulling on plug. Keep cord away from heat and sharp edges. Always disconnect the extension cord from the receptacle before disconnecting the product from the extension cord.

WARNING! To reduce the risk of electrocution, keep all connections dry and off the ground. Do not touch the plug with wet hands.

• Do not use the appliance if a supply cord or important parts of the appliance are damaged, e.g. safety devices, high pressure hoses, trigger gun.

• If an extension cord is used, the plug and socket must be of watertight construction.
  WARNING! Inadequate extension cords can be dangerous.

• Remove the plug from the socket-outlet during cleaning or maintenance and when replacing parts or converting the machine to another function.

PROPER USE OF THE PRESSURE CLEANER

THIS UNIT IS INTENDED FOR USE WITH COLD WATER ONLY! DO NOT USE HOT WATER IN THIS PRESSURE CLEANER.

1. Operate the pressure cleaner at no more than the fluid pressure rated for the pressure cleaner. Never run the pressure cleaner without a water supply. Running the unit without a water supply will cause irreparable damage to the unit
2. Make sure that the water supply you use for the pressure cleaner is not dirty, sandy, and does not hold any corrosive chemical products. Using a dirty water supply will compromise the long life of the pressure cleaner.
3. CAUTION -The pressure cleaner can be used for a variety of applications including washing cars, boats, patios, decks, garages etc. where high pressure is necessary to remove dirt and debris. High-pressure water flow can damage the work surface if not used properly! See the section titled “Operating Instructions” for more details. Always test the spray in an open area first
4. NEVER move the unit by pulling on the high pressure hose. Use the handle provided on the top of the unit
5. Always hold the high pressure gun and wand with two hands. Keep one hand on the gun/trigger, while supporting the wand with the other hand (see diagram).
6. When dispensing detergent, the pressure cleaner applies detergent to the cleaning area at low pressure only. Once the detergent has been applied, spray the detergent off of the work area by using the adjustable nozzle.

MACHINE DESCRIPTION

Unpacking the box
After opening the box, please remove all parts and check them against the following list of supplied components:

1. Water gun
2. Handle
3. Gun trigger
4. Hose holder
5. High-pressure hose – 5m
6. Jet extension
7. Water gun holder
8. Power on/off switch
9. Output thread
10. Mains cord holder
11. Shampoo container holder
12. Mains cord- 5m
13. Terminal input thread No.17
14. Cleaning needle
15. Variable jet
16. Shampoo container
17. Inlet filter terminal
18. hose quick coupling
19. Turbo jet
20. Car brush
21. Surface cleaner
    

ASSEMBLY INSTRUCTION

1. Attaching the gun holder (No. 7) and accessories **(fig. 1 below)

**

2.  Attaching the handle and hook to the hose

3. Atfach the handle onto the machine body (fig.2) and fasten it with 2 screws (fig.3).

4. Mountthe hook on the hose and fasten it with screws (fig.4, 5).
   

5. Attaching the cable holder and shampoo container

6. Place the hook on the body while standing and fasten it with screws (fig.6, 7)
   
   

7. Installing the inlet filter terminal

8. First remove the protective cover from the inlet thread (fig.8).

9. Then screw the end with the filter onto the thread (fig.9, 10).
   Note: The inlet filter must always be installed in the water supply line to filter out sand, limestone and other contaminants as they would damage the pump valves.
   ATTENTION! Failure to install the filter voids the warranty.
   

10. Connecting 2‘ diam. hose and quick coupling

11. Connect the 2” garden hose to the standard quick coupling as shown in fig.12 (quick coupling is included in package – No.18).

12. Then insert the quick coupling (No.18 ) onto the input terminal (No.17) until a click is heard, which means that the installation was successful. If not, water may leak at this point.
    

13. Water gun assembly

14. Insert the jet attachment (No.6) into the water gun (No.1).

15. After inserting, turn it by 90° until the locking end of the jet appears (fig.13, 14)

16. Then insert the required jet into the attachment (No.7). (fig.13, 14)
    
    

17. High-pressure hose assembly

18. Make sure the ON/OFF switch is in the OFF position (fig.15).

19. Attach the hose to the gun as shown in figure 16.

20. Remove the protective cover from the inlet thread (No.9), (fig.17).

21. Connect the high-pressure hose fo the outlet thread as shown in figure 18
    
    

22. Connecting the shampoo container

23. 1, Insert the shampoo container (No.16) into the jet attachment (No.6) as shown in fig.19.

24. After inserting, turn it by 90° until the locking end of the jet appears.
    
    Note: The detergent should be diluted with water to achieve the best possible effect.
    WARNING! NEVER USE PRODUCTS WITH BLEACHES, CHLORINE OR ANY OTHER CORROSIVE MATERIALS, INCLUDING SOLVENT-CONTAINING LIQUIDS (IE. GASES, OILS, ETC.), PRODUCTS WITH SODIUM PHOSPHATE, AMMONIA OR ACID-BASED CLEANERS. THESE CHEMICALS WOULD DAMAGE THE APPLIANCE AND WILL ALSO CAUSE DAMAGE TO THE CLEANED SURFACE. ALWAYS READ THE LABEL INFORMATION.

25. Surface cleaner assembly (No.21)

26. Proceed according to the fig.20 below.

27. Insert the U-pin and fasten the extension.
    Note: Make sure that the bottom of the cleaner is properly attached to the extension with the U-pin.
    

28. Car brush attachment (No.20)

29. Insert the jet attachment (No.6) into the water gun (No.1).

30. After inserting, turn it by 90° until the locking end of the jet appears (fig.21)

31. Then insert the car brush (No.20) into the attachment (No.7). fig.21)
    
    

OPERATING INSTRUCTION

THIS APPLIANCE IS INTENDED FOR USE WITH COLD WATER ONLY!
DO NOT USE HOT WATER IN THIS HIGH-PRESSURE CLEANER!

Starting
After connecting the high-pressure cleaner to the cold water supply, proceed as follows:

• Make sure the ON/OFF switch is in the OFF position.
• Assemble the machine according to steps 1 through 4 in Chapter 8. Assembly instructions
• Connect the hose to the inlet fiting according to assembly step No. 5.
• Assemble the gun according to step No.6 and insert the required jet (variable or turbo) or accessories from step No.8, 9, 10 into the gun.
• Connect the high-pressure hose according to assembly step No.7.
• Fully open the water inlet valve,
• Before turning on the instrument, press the trigger of the gun to remove any remaining air from the pump and hose.
• To start the high-pressure cleaner, set the ON/OFF switch to the ON posttion and press the trigger. REMINDER: The engine does not run continuously unless the trigger is depressed.

WARNING!
RISK OF INJECTION! Unit will start spraying when trigger is squeezed, When turning the unit off after use, high pressure still exists inside the hose and unit. Point the gun in a safe direction and discharge the excess pressure. NEVER direct the high pressure water stream at people or animals.

Automatic On/Off
The pressure cleaner is equipped with an automatic on/off switch. The pressure cleaner will only run when the power switch isin the ON position and the trigger on the gun is squeezed. When you release the trigger to stop spraying water through the gun, the motor on the pressure cleaner will automatically shut off. Simply squeeze the trigger again to resume using the cleaner. To stop using the pressure cleaner, release the trigger and switch the unit fo the OFF position. The unit should be turned completely OFF while not in use or while unattended.

Bleeding the Gun
Itis very important fo bleed the gun before using the pressure cleaner. Refer to the “Assembly Instructions” to assemble the pressure cleaner. To bleed the gun, simply connect the garden hose to the pressure cleaner and ‘squeeze the trigger BEFORE turning the electrical supply on. This allows any air rapped inside the pressure cleaner and gun to be removed before using the unit. Continue holding trigger for approximately one minute to allow any excess air out of the unit. Water will flow through the gun at low pressure during this procedure. For more bleeding tips, see the section titled “Operating Instructions.”

Gun Safety Lock
This pressure cleaner is equipped with a gun trigger safety lock. When not using the pressure cleaner, use the safety lock to Keep from accidentally engaging the high pressure sproy.

Adjustable Spray Nozzle
The adjustable nozzle will allow you to use any variety of spray patterns from a fullfan spray to a direct stream spray.When using the pressure washer to clean wood decks, siding, vehicles etc, always start using the fan spray and begin spraying from a minimum 36″ away to avoid damaging the surface of the material you are cleaning. Always begin by spraying in a testing area free and clear of people and objects.

Warning! Do not do this under operation to avoid that the hand hits the jet

Warning! High pressure jets can be dangerous if subject to misuse. The jet must not be directed at persons, live electrical equipment or the appliance itsett.

• Do not direct the jet against yourself or others in order to clean clothes or footwear.

CLEAN-UP AND STORAGE

Shutting Down the Pressure Cleaner

WHEN FINISHED USING THE PRESSURE CLEANER, FOLLOW THESE STEPS TO SHUT DOWN THE UNI

• Turn the pressure cleaner to the OFF position.
• Turn off the water supply.
• Before disconnecting high-pressure hose connection, point the gun in a safe direction and discharge the high-pressure water,
• Disconnect high-pressure hose from the pressure cleaner and gun.
• Disconnect garden hose from the pressure cleaner.
• Remove quick couple fiting from garden hose and attach to the nipple portion of the fitting installed on the pressure cleaner for storage.
• Remove excess water from the pump by tipping the unit on both sides to drain any remaining water from inlet cand outlet fittings.
• Remove Water Intake Filter and flush with water to remove dirt or debris. Return fier once cleaned.
• Drain detergent reservoir and flush with running water.
• Wipe away any remaining water on all parts and fitings.
• Engage the gun safety lock.
• Store the pressure cleaner, parts, and accessories in an area with a temperature above 0 °C (32 °F).

Winterizing and Long-Term Storage

FOLLOW ALL OF THE ABOVE SHUT-DOWN PROCEDURES, ADDING THE FOLLOWING STEPS…

• After disconnecting the water supply, and before disconnecting the high-pressure hose, turn the pressure cleaner on for 243 seconds, until any remaining water in the pump exits.

TURN UNIT OFF IMMEDIATELY. CONTINUED USE OF THE PRESSURE CLEANER WITHOUT WATER SUPPLY ATTACHED WILL CASE SEVERE DAMAGE TO THE UNIT!

• Always store the pressure cleaner, parts, and accessories in an area with a temperature above 0 °C (32°F).

WARNING!
FAILURE TO COMPLY WITH THESE STORAGE INSTRUCTIONS WILL RESULT IN DAMAGE TO THE PUMP ASSEMBLY.

MAINTENANCE

• This pressure cleaner is supplied with a closed lubrication system, so no addition of oilis needed,
• Check all hoses and accessories for damage prior to use.
• Check the inlet filter periodically for deposits. Clean this filer regularly for maximum performance.

CLEANING TIPS

WARNING! ALWAYS TEST THE SPRAY IN AN AREA FREE AND CLEAR OF PEOPLE AND OBJECTS BEFORE YOU SPRAYAT THE INTENDED CLEANING SURFACE.

Wood and Vinyl Decks
Rinse deck and surrounding area with fresh water. using detergent, il the detergent reservoir and apply to the «rea being cleaned at low pressure. For optimal resuls, reduce your work area to smaller sections and clean each section one at a time. Allow the detergent to rest on the surface for a few minutes and then rinse at high pressure, DO NOT LET THE CLEANSER DRY. Always clean from left to right and top to bottom for best results.
Rinse at high pressure using the fan spray keeping the tip of the spray nozzle at least 6 9 inches from the cleaning surface. Maintain a further distance from the cleaning area when using a direct spray.

CAUTION! For softer woods, increase the distance from the cleaning area.

Cement Patios, Stone, and Brick
Rinse cleaning and surrounding area with fresh water, If using detergent, fil the detergent reservoir and apply to the area being cleaned at low pressure. Rinse at high pressure using the fan spray in a sweeping motion keeping the tip of the spray nozzle at least 3-6 inches from the cleaning surface. Maintain a further distance from the cleaning area when using a direct spray.

Cars, Boats, and Motorcycles
Rinse cleaning and surrounding area with fresh water. If using detergent, fil the detergent reservoir and apply to the area being cleaned at low pressure. To achieve the best results, clean one side at a time. Allow the detergent to rest on the surface for a few minutes, but do not let the detergent dry. Rinse at high pressure using the fan spray in a sweeping motion keeping the tip of the spray nozzle at least 8 inches from the cleaning surface. Maintain a further distance from the cleaning area when using a direct spray. Wipe surface dry for a polished finish.

Barbecue Grills, Power Equipment, and Garden Tools
Rinse cleaning and surrounding area with fresh water. If using detergent, fill the detergent reservoir and apply to the area being cleaned at low pressure. Allow the detergent to rest on the surface for a few minutes, but do not le the detergent dry. Rinse at high pressure using the fan spray keeping the tip of the spray nozzle at least 1Biinches from the cleaning surface. Maintain a further distance from the cleaning area when using a direct spray.

TECHNICAL SPECIFICATIONS

WARRANTY
See the enclosed warranty conditions for warranty conditions.

ENVIRONMENT
It your appliance must be replaced after a prolonged period of being unused, do not throw it into the household waste, but dispose of iin an environmentally friendly way.

DISPOSAL

The machine, rechargeable batteries, accessories and packaging should be sorted for
environmentatfriendly recycling.

Do not dispose of power tools and batteries/rechargeable batteries into household waste!

Only for EC countries:

According to the European Guideline 2012/ 19/EU, power tools that are no longer usable, and ‘according to the European Guideline 2006/66/EC, defective or used battery packs/batteries, must be collected separately and disposed of in an environmentally correct manner.

INSTRUCTIONS AND INFORMATION ON DISPOSAL OF USED PACKAGING.
Put any used package material to the place determined by the municipality for waste disposal.

DISPOSAL OF USED ELECTRIC AND ELECTRONIC EQUIPMENT

This symbol on products or accompanying documents means that used electric or electronic products must not be put fo ordinary municipal waste. Hand over such products to determined collection points for proper disposal, restoration and recycling. Alternatively, in some countries of the European Union or other European countries you can return your products to your local dealer when you buy an equivalent new product. By dutiful disposal of this product you can preserve precious natural resources and you help prevent any potential adverse effects on the environment and human health which could be the results of wrong waste disposal. Ask your local authority or the nearest collection point for additional details. In case of improper disposal of this waste kind penalties can be imposed in accordance with national regulations.

For companies in the European Union countries
Should you want to dispose of electric and electronic devices, ask your dealer or vendor for necessary information…

Disposal in other countries outside the European Union
Should you want to dispose of this product, ask your local authorities or your dealer for necessary information about disposal method.

This product fulfils all basic requirements of the EU directives that apply to it.

Text, design and technical specifications can change without prior notice and we reserve the right for their change.

DECLARATION OF CONFORMITY

EU DECLARATION OF CONFORMITY

Product/ brand: Electric High Pressure Cleaner / FIELDMANN

Type/ model: FDW 201650-E as factory model HRAO3P ‘AC 230-240 V, 50 Hz, 1650 W, max. 7 I/min, 13,5Mpa, IPXS, Class Il LpA 87 dB(A), LwA 93 dB(A)

Manufacturer: FAST CR, a.s. Cernokosteleckd 2111, 100 00 Praha 10, Czech Republi
VAT no: (226726548

‘The product is inline with directives and regulations listed below:
Directive MD 2006/42/EC
Directive EMC 2014/30/EU
Directive NOISE 2000/49/EC
Directive RoHS 2011/65/EU and norms:

EN 60335-1:2012+A11+A13+A1+A14+A2
EN 60335-2-79:2012
EN 62233:2008
EN 55014-1:2017+A11:2020
EN 55014-2:2015,
EN IEC 61000-3-2:2019
EN 61000-3-3:2013+A1:2019
EN IEC 61000-3-11:2019

ICO: 26726548, DIC; CZ26726548
Bankovni spojeni: Komeréni banka Praha 1, ¢.0. 8930901 1/0100, CSOB Praha 1, ¢.. 8010-0116233383/0300 Ceska spofitelna Praha 4, €.u. 2375682/0800

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>