beper P203PAN002 Patio Quartz Heater with Floor Stand Instruction Manual
- June 9, 2024
- beper
Table of Contents
beper P203PAN002 Patio Quartz Heater with Floor Stand Instruction Manual
Precautions
Read the following instructions carefully, since they give youuseful safety information about installation, use and maintenance and help you avoid mishaps and possible accidents. Remove the packing and make sure that the appliance is intact, with special attention to the supply cable. The elements of the packing (plastic bags, polystyrene, etc) do not have to be accessible to the children, in order to preserve them from danger sources. It is recommended not to throw these packing material in the domestic waste, but to deliver them to the appropriate station of collection or destruction refusals, asking eventually information to the manager of the Sanitation Department of your own municipality. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
Before connecting the appliance make sure that the mains voltage corresponds to the data specified on the label. The appliance can be damaged if the voltage is not correct. If the plug does not suit the socket, let it be replaced with another suitable plug by qualified personnel only, which shall also ensure that the section of the socket cables is suitable for your appliance power absorption. Generally, the use adaptors multiple plugs and/or extensions is not recommended; should they be necessary, please use only simple or multiple adaptors and extensions in compliance with the safety rules in force, making sure that the capacity absorption limit marked on the simple adaptors and the extensions and the maximum power limit marked on the multiple adaptor are not exceeded. Do not use the appliance if the cable or the plug shows any damages. Do not use the appliance after a possible irregular working. In this case, switch it off and do not break it open. Refer to an authorized Beper after-sale service for repair and require original spare parts only. Failing to follow these instructions may impair the safety of your appliance. This appliance is to be destined to its special purpose only. Any other use is to be considered as improper and thus dangerous. The manufacturer cannot be responsible for any damages deriving from improper, wrong or incautious use.
This appliance is for household use only. To protect against electric shock,
do not immerse cord, plug or any parts of the appliance into water or other
fluids. Do not use the appliance near explosives, highly flammable materials,
gases or burning flames.
Do not allow children, disabled people or every people without experience
or technical ability to use the appliance if they are not properly watched
over. Close supervision is necessary when any appliance used by or near
children.
Product description Fig. A
- Heating elements assembly
- Fixing knob for heating elements assembly
- Support for heating elements assembly
- Power selection indicator
- Pull switch
- Pole cover
- Upper pole
- Pole fixing screws (3x)
- Middle pole
- Pole fixing screws (3x)
- Lower pole
- Power cable clamp
- Power cable
- Base fixing cover
- Screws for base (4x)
- Base assembly
- Floor fixing kit (3x screws; 3x anchors)
Warnings for use
Remove all packaging materials before assembling and using the appliance,
making sure to keep them out of the reach of children and pets. Never touch
the heating elements assembly when the appliance is operating: risk of
burnings. Do not tilt the heating elements assembly when the appliance is
operating. Wait at least 15 minutes after the appliance has been shut off
before adjusting tilt. Do not cover the grid protecting the heating elements,
to avoid any risk of overheating. Do not use the appliance to dry clothing and
linen. After switching the appliance off, even if the heating elements are
off, they can still be very hot, and thus dangerous. Make sure the appliance
is switched off before carrying out any assembling and/or maintenance
operation. Do not attempt to modify/repair the appliance in any way. Do not
install and/or use the appliance near showers, bath tubs, swimming pools, etc.
This appliance is specifically designed for domestic use in gardens, terraces,
patios, arcades and outdoor environments in general. However, it is necessary
to ensure that the plug is connected indoors, away from rainf and other
atmospheric agents. The appliance is equipped with an anti-tilt safety switch,
that automatically stops the operation fo the appliance in case the base is
not touching the ground; after replacing the appliance on the floor, the
safety switch will automatically turn the appliance back on. The height of the
floor stand is adjustable up to 200 cm; however, it is necessary that the
heating elements assembly is installed at a minimum height of 180 cm when the
appliance is in use. Before moving the appliance, make sure that it is
switched off and unplugged from the wall socket.
This appliance can only be used by children of 8 years of age or older, and by people with reduced physical, sensitive or mental capabilities, or with lack of experience and knowledge, provided that they have been given complete instructions concerning the safe use of the appliance and the risks related to its use. Children must not play with the appliance. Cleaning and maintenance operations must not be carried out by children without supervision. Children of 3 year of age or younger cannot play or remain close to the appliance unless they are constantly supervised.
Warning: some parts of the appliance can get really hot during operation, it is necessary to pay extreme attention in the presence of children or vulnerable persons.
Warning: to avoid overheating, do not cover the appliance.
Do not place the appliance immediately below a wall-socket outlet.
Do not use this appliance in combination with timers or other similar devices
that control its operation automatically, because there is a risk of fire in
case the appliance is incorrectly placed or it is covered.
Do not place the appliance near combustible and/or inflammable materials.
Assembling Fig. B, C
Remove all packaging materials, and make sure that all components are provided in the box. Place the base assembly on a flat and stable surface. Remove all 8 screws by using a Phillips screwdriver. If you wish to permanently install the base on the floor, remove the metal base cover, and place the base where you intend to install the appliance. Mark the holes where the anchors will be installed with a pencil, following the guiding holes on the base. Use a drill to make the holes and insert the anchors; place the base on the holes and firmly fix it with the screws provided. In case the appliance does not have to be drilled to the floor, place the base assembly on a flat and stable surface, and only remove 4 of the 8 screws found on the base (leaving the others in place). Place the lower pole on the base, aligning the holes found on the tube with those on the base; insert the screws and securely fix them with a hand or electric screwdriver. At this point, slide the base fixing cover down, to cover the screws, and place a power cable clamp on the upper part of the pole. Connect the medium pole to the lower pole, aligning the holes found on both poles; insert 3 pole fixing screws and securely tighten them with a screwdriver; then inser a power cable clamo. Connect the upper pole to the medium pole, and proceed as described above. To adjust height, untighten the pole cover and extract the telescopic pole to the desired height; then fix it by tightening the pole cover. Finally, install the heating elements assembly on to the telescopic pole, and fix it by tightening the fixing knob; slide the power cable throught the clamps. To adjust tilt, move the heating elements assembly up or down, paying attention not to force the movement beyond the permitted level, to avoid damaging the assembly and its support.
Warning: the heating elements assembly can reach very high temperatures during its operation; make sure to adjust tilt before switching the appliance on and/or at least 15 minutes after it had been shut off.
Operation
Connect the appliance to a wall socket, and pull the switch down; the indicator will show level 1, and the appliance starts working at the lower power setting (650W). By pulling the switch again, it will be possible to select power level 2 – medium (1300W), while pulling the switch one more time the max power level 3 will be selected (2000W). By pulling the switch one last time, the appliance will be turned off
Warning: it is normal to hear a slight vibration when the appliance is switched on; this vibration is due to the quartz heating elements, that take a few seconds to fully activate. When the heating elements start glowing, the vibration will stop.
Cleaning and maintenance
Make sure that the appliance is switched off, completely cold and unplugged
from wall socket before proceeding with any cleaning or maintenance
operations. Use a soft cloth dampened with water if necessary to remove dust
and/or stains from the base, the poles and outer surface of heating elements
assembly
Warning: do not immerse the appliance in water or other liquids; do not spray water or other liquids directly into the protection grid of the heating elements assembly
Technical data
- Power: 2000W max
- Power supply: 220-240V 50/60Hz
For any improvement reason, Beper will reserve the right to modify or improve this appliance without notice.
The European directive 2011/65/EU on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimize the recovery and recycling of the materials they contain, and reduce the impact on human health and the environment. The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the appliance, it must be separately collected.
GUARANTEE CERTIFICATE
This appliance has been checked in the factory. From the date of original purchase a 24 month guarantee applies to material and production defects. The purchase receipt and the guarantee certificate must be submitted together in case of claim to guarantee
The guarantee is valid only with a guaranty certificate and proof of purchase (fiscal receipt) indicating the date of purchase and the model of the appliance
For any technical assistance, please contact directly the seller or our head office in order to preserve the appliance’s efficiency and NOT TO void the guarantee. Any intervention on this appliance by non-authorized persons will automatically void the guarantee
GUARANTEE CONDITIONS
If the appliance shows defects as a result of faulty material and/or production during the period of guarantee, we guarantee repair free of charge on condition that:
- The appliance has been used properly and for the purpose for which it has been intended.
- The appliance has not been tampered with, otherwise it is not maintainable.
- The purchase receipt shall be presented.
- The appliance showing a fair wear and tear shall not be covered by this guarantee.
Therefore, any part that could be accidentally broken or having visible signs of use in consumable products (such as lamps, batteries, heating elements…) the aesthetic parts are excluded from the guarantee, and any defect whatsoever resulting from non-respect of the rules for use, negligence in usage and/or maintenance of the appliance, carelessness, wrong or improper installation, damage during transport and any other damage not attributable the supplier.
For every defect that could not be repaired within the guarantee period, the appliance will be replaced free of charge.
In any case, if the part to be replaced for defect, breakage or malfunction is an accessory and/or a detachable part of the product, Beper reserves the right to replace only the very part in question and not the entire product
Contact your distributor in your country or after sales department Beper.
E-mail assistenza@beper.com which will forward your enquiries to your distributor.
Electric Bag Water
- Cod.: P203TFO001
Fast charging in less than 15 minutes Keeps warm up until 2 hours Cordless
operation, it can be used everywhere Ready to use: no water filling needed
Protection against over heating
CUSTOMER CARE BEPER
Via Salieri, 30 – 37050 – di – Verona
Tel. 045/7134674 – Fax 045/6984019
beper.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>