HOLOPHANE ARE3 Arlington Postop LED Retrofit Kit Instruction Manual
- June 9, 2024
- HOLOPHANE
Table of Contents
ARE3 Arlington Postop LED Retrofit Kit
Instruction Manual
ARE3 Arlington Postop LED Retrofit Kit
READ AND FOLLOW ALL SAFETY INSTRUCTIONS!
SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION
- To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards please read all warnings and instructions included with and on the fixture box and all fixture labels.
- Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
- Installation and service of luminaires should be performed by a qualified licensed electrician.
- Maintenance of the luminaires should be performed by person(s) familiar with the luminaires’ construction and operation and any hazards involved. Regular fixture maintenance programs are recommended.
- It will occasionally be necessary to clean the outside of the optic/lens. Frequency of cleaning will depend on ambient dirt level and minimum light output which is acceptable to user. Optic/lens should be washed in a solution of warm water and any mild, non-abrasive household detergent, rinsed with clean water and wiped dry. Should optical assembly become dirty on the inside, wipe optic/lens and clean in above manner, replacing damaged gaskets as necessary.
- DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have been damaged during transit. Inspect to confirm. Any part damaged or broken during or after assembly should be replaced.
- Recycle: For information on how to recycle LED electronic products, please visit www.epa.gov.
- These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation, operation, or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s or owner’s purposes, this matter should be referred to Acuity Brands Lighting, Inc.
WARNING
RISK OF ELECTRIC SHOCK
✓ Disconnect or turn off power before installation or servicing.
✓ Verify that supply voltage is correct by comparing it with the luminaire
label information.
✓ Make all electrical and grounded connections in accordance with the National
Electrical Code (NEC) and any applicable local code requirements.
✓ All wiring connections should be capped with UL approved recognized wire
connectors.
WARNING
RISK OF BURN
✓ Allow lamp/fixture to cool before handling. Do not touch enclosure or light
source.
✓ Do not exceed maximum wattage marked on luminaire label.
✓ Follow all manufacturer’s warnings, recommendations and restrictions for:
driver type, burning position, mounting locations/methods, replacement and
recycling.
CAUTION
RISK OF INJURY
✓ Wear gloves and safety glasses at all times when removing luminaire from
carton, installing, servicing or performing maintenance.
✓ Avoid direct eye exposure to the light source while it is on.
CAUTION
RISK OF FIRE
✓ Keep combustible and other materials that can burn, away from lamp/lens.
✓ Do not operate in close proximity to persons, combustible materials or
substances affected by heat or drying.
CAUTION: RISK OF PRODUCT DAMAGE
✓ Never connect components under load.
✓ Do not mount or support these fixtures in a manner that can cut the outer
jacket or damage wire insulation.
✓ Unless individual product specifications deem otherwise: Never connect an
LED product directly to dimmer packs, occupancy sensors, timing devices, or
other related control devices. LED fixtures must be powered directly off a
switched circuit.
✓ Unless individual product specifications deem otherwise: Do not restrict
fixture ventilation. Allow for some volume of airspace around fixture. Avoid
covering LED fixtures with insulation, foam, or other material that will
prevent convection or conduction cooling.
✓ Unless individual product specifications deem otherwise: Do not exceed
fixtures maximum ambient temperature.
✓ Only use fixture in its intended location.
✓ LED products are Polarity Sensitive. Ensure proper Polarity before
installation.
✓ Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal
grounding equipment must be worn during all installation or servicing of the
unit.
✓ Do not touch individual electrical components as this can cause ESD, shorten
lamp life, or alt er performance.
✓ Some components inside the fixture may not be serviceable. In the unlikely
event your unit may require service, stop using the unit immediately and
contact an ABL representative for assistance.
✓ Always read the fixtures complete installation instructions prior to
installation for any additional fixture specific warnings.
Please see product specific installation instructions for additional warnings
or any applicable FCC or other regulatory statements.
Failure to follow any of these instructions could void product warranties. For
a complete listing of product Terms and Conditions, please visit
www.acuitybrands.com.
Our Brands| Indoor/Outdoor
Lithonia Lighting
Carandini
Holophane
RELOC| Indoor Lighting
Gotham
Mark Architectural Lighting
Peerless
Renaissance Lighting
Winona Lighting| Outdoor Lighting
American Electric Lighting
Antique Street Lamps
Hydrel
Tersen| Controls
DARK TO LIGHT
Lighting Control & Design
ROAM
Sensor Switch
Synergy
---|---|---|---|---
Acuity Brands Lighting, Inc. assumes no responsibility for claims arising out of improper or careless installation or handling of its prod ucts.
INTRODUCTION
1.1 Product Description.
This post top luminaire is designed with LED’s which do not require
replacement.
The luminaire includes a plug-in electrical module that contains the
photocontrol receptacle when specified. These modules are common to all
luminaire styles in this series.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
1.2 Alternate Information Sources.
Holophane
Field Service Department
P.O. Box 3004
Newark, OH 43058-3004
866-759-1577
INSTALLATION
2.1 Tools and Material Required.
Table 1. Installation Tools and Materials
DESCRIPTION | USE |
---|
Flat-end Screwdriver
1/4” Nut driver
1/8″ Allen Wrench
Torque Wrench| Installation of electrical wiring
Electrical tray and reflector screws
Set screws (Mounting)
Set screws
2.2 Luminaire Installation.
2.2.1 Place and level the luminaire on the pole.
2.2.2 Orient Housing such that street aiming rib faces the street. See
Figure 1
2.2.3 Alternate tightening of the four set screws (See Figure 1) will assist
in centering the luminaire on the post capital. Tighten the four set screws to
45-50 inch – pounds. (If the GV1A73 accessory is included; follow that torque
specification for that part).
Figure 1
2.2.4 Remove latch screw and latch and lift cover. Secure cover to remain in
the open position. See Figure 2.
2.2.5 Disconnect the main power quick-disconnect and photo control circuit (If
equipped with photo control option) and remove LED heat sink assembly and
support on a clean horizontal work surface. See Figure 2.
Figure 2
2.2.6 Loosen reflector screws and remove reflector.
2.2.7 Remove cable bracket screws and lift bracket off optic. Keep cable(s)
zip-tied to bracket.
2.2.8 Remove optic.
2.2.9 Loosen two keyway screws, then turn and remove electrical tray; gently
lay on its side to allow driver bracket to rest between arms of housing.
Figure 3 shows electrical tray removed for clarity.
2.2.10 Insert the electrical supply wiring into the luminaire wiring chamber
through the center slot in the provided gasket. See Figure 3.
2.2.11 Wire incoming leads to electrical tray accordingly. Connect incoming
ground wire to ground wire attached to inside of wiring chamber. Carefully
place connections in wiring chamber for future access.
2.2.12 For units equipped with 0-10V dimming, locate the gray and violet leads
coming from the driver. If the unit is to be connected to dimming control gear
(not included), trim, strip and connect these leads per the dimming control
gear manufacturer’s instructions. The violet lead is positive, and the gray
lead is negative. If the unit is not to be
connected to dimming control gear, leave the leads individually capped.
2.2.13 Replace electrical tray on keyway slots, twist clock-wise and tighten
screws.
CAUTION
LEADS USED FOR DIMMING CONTROLS ARE TO BE SEPARATED FROM MAIN POWER CONDUCTORS
IN A MANNER TO SATISFY STATE AND LOCAL CODES.
Figure 3
2.2.14 Re-install optic.
2.2.15 Re-install cable bracket and tighten bracket screws.
2.2.16 Orient “street side” on optic with street side rib on housing.
See Figure 4.
2.2.17 Re-install reflector and tighten reflector screws.
Figure 4
2.2.18 Re-install LED heat sink assembly by orienting “latch” on heat sink with “street side” on optic and street side rib. See Figure 5.
2.2.19 Close cover while ensuring no leads are pinched. Engage and secure the
latch.
2.2.20 Units supplied with a photo control option require a shorting plug or a
twist lock photo control to be installed. Install the device by twisting it
clockwise. See Figure 1.
CAUTION
A PHOTO CONTROL THAT MEETS THE REQUIREMENTS OF ANSI C136.10 AND WITH A CLEAR
WINDOW ON THE SIDE THAT EXPOSES THE PHOTOCELL MUST BE USED.
2.2.19 Energize the unit and check for proper operation.
MAINTENANCE
3.1 Cleaning
3.1.1 Make sure the unit is de-energized.
3.1.2 Wipe off exterior dirt and debris using a soft, clean cloth.
CAUTION
DO NOT USE ABRASIVE CLEANSERS ON OPTICAL SURFACES. THEIR USE MAY RESULT IN THE
LOSS OF OPTICAL EFFICIENCY.
3.2 Electrical Component Replacement
3.2.1 To replace photocontrol. (If provided) Make sure the unit is de-
energized. Twist counterclockwise and remove. Replace with equivalent
photocontrol.
3.2.2 For all other electrical parts- Make sure the unit is deenergized. Open
housing by unscrewing and removing latch and latch screw (Figure 1). Lift
cover and secure to remain in the open position. Disconnect the main power
quick-disconnect and photo control circuit (if applicable) and remove LED heat
sink assembly and support on a clean horizontal work surface. See Figure 2.
Remove the reflector by loosening (2) screws. Remove cable bracket screws and
lift bracket off optic. Keep cable(s) zip-tied to bracket. Remove optic. See
Figure 3.
3.2.3 To replace LED driver. Make sure the unit is de-energized. Loosen and
remove electrical tray to access parts. Disconnect input and output via quick
disconnects and remove (2) mounting screws. Replace with Holophane approved
driver. See Figure 6. If no other components are to be replaced go to Section
3.2.6.
Figure 6
3.2.4 Replacement of surge protector. Disconnect quick disconnect plug coming
from terminal and quick disconnect going to optical compartment. Remove SPD
SCREW connecting the surge protector to the plate; retain screws for re-
installation.
3.2.5 For standard surge units, remove the screw from mounting bracket and
slide surge protector through opening in mounting bracket. Replace with
Holophane approved device. See Figure 4.
3.2.6 Bundle and secure the wiring in a manner like the way it was originally
secured to avoid pinching of wires when re-installing the module into the
housing.
3.2.7 Replace electrical tray on keyway slots, twist clock-wise and tighten
screws.
3.2.8 Replace optic, cable bracket, reflector, LED heat sink assembly making
sure to reconnect wiring cable(s), cover, latch, and latch screw.
HARNESS NOTES
Any slack in the harnesses should neatly be pushed through the ce nter opening
in the lower reflector as the cover is closed.
3.2.9 Energize the unit and check for proper operation.
LIMITED WARRANTY AND LIMITATION OF LIABILITY
The Holophane limited warranty and limitation of liability is published in the “Terms and Conditions” section of the current Holophane buyer’s guide, and is available from your local Holophane sales representative.
Acuity Brands Lighting, Inc.
3825 Columbus Rd SW, Granville, OH 43023
IM-433-A, 6/20/18 ©2018 Acuity Brands Lighting Inc.,
All Rights Reserved
Visit our web site atwww.holophane.com
Printed in USA
ABL LED General Warnings, Form No. 503.203
© 2011 Acuity Brands Lighting, Inc. All rights reserved. 3/15/11
IM-433-C
Documents / Resources
|
HOLOPHANE ARE3 Arlington Postop LED Retrofit
Kit
[pdf] Instruction Manual
ARE3, JFE3, Arlington Postop LED Retrofit Kit, Postop LED Retrofit Kit,
Arlington Retrofit Kit, Postop LED, Retrofit Kit
---|---
References
- Acuity Brands | Lighting, Controls, and Building Management Solutions
- Fabricantes de alumbrado publico e iluminación inteligente - CARANDINI
- U.S. Environmental Protection Agency | US EPA
- U.S. Environmental Protection Agency | US EPA
- Holophane | Lighting solutions for commercial, industrial, emergency and outdoor applications.
- Holophane | Lighting solutions for commercial, industrial, emergency and outdoor applications.
- Lithonia Lighting® | Best Value in Lighting
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>