FEELWORLD W1000S Wireless Video Transmission System User Manual

June 9, 2024
FEELWORLD

FEELWORLD W1000S Wireless Video Transmission System

FEELWORLD-W1000S-Wireless-Video-Transmission-System-
PRODUCT

FOREWORD

Thank you for purchasing FEELWORLD wireless video transmission system. Please read this manual carefully before using the product, wish you a happy experience!

Caution
Do not expose this device to extreme hot, cold, dusty or humid environments. Do not scratch the device with sharp objects. Do not drop this device from high place, as this may cause hardware damage. This device is designed for non-water proofing. Please do not allow any liquid to penetrate into the device. Do not attempt dismantle, open or repair this device by non- technical person, as this may cause permanent damage to the device.

Features
Dual HDMI & SDI (optional) signal interfaces Transmission range up to 1000ft, with ultra-low latency 0.08S Up to 1080P60Hz  With type-C to Ethernet adapter accessory, achieve live streaming The transmitter can be switched as a receiver at will. Wireless full-duplex talkback, real-time intercom between the director and the photographer. One TX to multiple RX Support APP monitoring for Android/IOS system.

INSTALATION INSTRUCTIONS

FEELWORLD-W1000S-Wireless-Video-Transmission-System-
FIG-1

PORT INSTRUCTIONS

FEELWORLD-W1000S-Wireless-Video-Transmission-System-
FIG-2

Transmitter

  1. Antenna Ports
  2. Power OFF/ON
  3. Type-C Power Input/Upgrade
  4. DC Power IN
  5. OLED Screen
  6. UP button
  7. OK button
  8. DOWN button
  9. HDMI Signal Output
  10. HDMI Signal Input
  11. SDI Signal Input ( optional)
  12. 3.5mm Earphone Port
  13. 1/4 Screw Hole

FEELWORLD-W1000S-Wireless-Video-Transmission-System-
FIG-3

Receiver

  1. Antenna Ports
  2. Power OFF/ON
  3. Type-C Power Input/Upgrade
  4. DC Power IN
  5. OLED Screen
  6. UP button
  7. OK/MENU button
  8. DOWN button
  9. HDMI Signal Output1
  10. HDMI Signal Output2
  11. SDI Signal Output(optional)
  12. 3.5mm Earphone Port
  13. 1/4 Screw Hole

UI INSTRUCTIONS

Startup
The startup screen is as above. When the device runs, the main menu will display.

Main Menu
Main menu including channel, device type(TX/RX), link status, signal strength, video format, intercom mode, battery level, temperature, fan status, etc. information.

  1. Channel switch: press“△”or“▽”to change channels. Press“□”to confirm the channel.
  2. Long press“△”on the transmitter, the screen will display device name and password. Long press“△”on the receiver, the screen will also display device name and password if it is connected to transmitter.

Secondary Menu

  • Long press“□”for 2 seconds to enter into the secondary menu.
  • Long press“□”for 2 seconds again to back to the secondary menu.
  • Press“△”or“▽”to switch the options in secondary menu and
  • press“□”to confirm selection.

Device (transmitter only):
device type Switch TX (transmitter) and RX (receiver) manually.

Source (transmitter with SDI port only):
signal source Switch the signal source between HDMI and SDI on transmitter. SDI input is selected by default if both HDMI and SDI sources are connected.

FAN status
Turn on or off the fan manually

Intercom
Switch between Full Duplex, TD mode(TD speak, Cameraman listen), OFF(turn off intercom)

WPS: pairing
To pair transmitter and receiver. One Transmitter allows to pair 4 receiver maximum. Turning on WPS both for transmitter and receiver at the same time, then turn off the receive which finished pairing. Using the same pairing method to add next one receiver. Last, turning on all of the paired devices.

Priority
Choose high image quality prior or low latency prior.

WIFI_SSDI
Showing device name and password

Version
Showing the device’s version number

Web

Telephone

Language

IP : IP address (only the receiver has this menu)

STREAMING INSTRUCTIONS

After the receiver links to transmitter and receives the video, plug the Type-C to Ethernet adapter to receiver’s Type-C port. The Type-C to Ethernet adapter will flash red light.

Static IP setting

  1. The receiver’s default mode is static IP. It can be selected in the secondary menu IP->staticIPFEELWORLD-W1000S-Wireless-Video-Transmission-System-FIG-17
  2. As the picture shown above, connect the Type-C to Ethernet adapter with computer via LAN cable.
  3. The receiver’s static IP address is 192.168.11.111. It can be found on the receiver’s secondary menu. The computer also has to be set to static IP. Set the computer’s static IP to be 192.168.11.xxx, xxx can be replaced by any number between 2 and 254 not include 111. After the settings completed, run CMD->ping 192.168.11.111 on computer to check if it works.
  4. Use the URL rtsp://192.168.11.111:554/test.264 on up streaming software such as VLC or OBS.

RouteIP setting

  1. Enter into the secondary menu on the receiver’s IP. Then select routeIPFEELWORLD-W1000S-Wireless-Video-Transmission-System-FIG-18
  2. Connect a monitor to the receiver. Then connect the receiver to the router via the Type-C to Ethernet adapter. If the blue light flashes on the adapter, it indicates that the connection is good. The monitor will show the IP address.
  3. Connect the computer to the router. Push streaming with the url: rtsp://IP address shown on the monitor/test.264

APP OPERATION INSTRUCTIONS

APP Download

  • iOS APP Download iOS user search “feelworld ” to get (APP name: MMonitor)
  • Android APP Download (APP name: Feelworld Wireless) Search “feelworld wireless” on Google Play to get
  • Scan the QR code to downloadFEELWORLD-W1000S-Wireless-Video-Transmission-System-FIG-21

Connect smart devices to transmitter
After the transmitter is powered on, go to Setting-Wireless & networks on smartphone/tablet, select the transmitter’s name and input the password to connect the devices. Please find the transmitter’s name and initial password as below. Then go to APP home page and click “Video” to monitor.

( Note : No need to input password again if it was saved on smart phone/tablet)

  • Device name : FEELWORLD_5G_XXXXX
  • Password : 12345678

APP Operation ( e.g. Android System)

  1. Click “Video” on home page to enter into monitoring mode.FEELWORLD-W1000S-Wireless-Video-Transmission-System-FIG-22
  2. Click “∨” at the bottom of screen. It will show SAVE IMAGE, RECORD ( only available for Android at present), MATERIAL, CONFIGURATION.

FEELWORLD-W1000S-Wireless-Video-Transmission-System-
FIG-23

Long press the screen to show up the professional monitoring menu. Monochrome, False Color, Center Marker are available at present, more features are developing.

  1. Click “Material”to check the images and videos saved on smartphone/tablet.
  2. Click “ Configuration”to access configuration screen.
  3. Click Chinese Version at the bottom of home page to change language.

PARAMETERS

| Transmitter| Receiver
---|---|---
Screen| OLED| OLED

Interface

| 1 * SDI input (optional)

HDMI input, 1 HDMI output

2  *Antenna port (RP-SMA Male)

DC power input, 3.5mm headphone jack , Type-C

| 2* HDMI output

1* SDI output (optional)

2 *Antenna port (RP-SMA Male)

DC power input, 3.5mm headphone jack, Type-C

Power Supply Way/Voltage Range

| F970 battery , Type-C: 5V/1.5A DC adapter: 6-16V

Note: Due to the actual output of some batteries will be greater than 16V, it may burn out. Please make sure that the actual output voltage

of the battery used is less than 16V.

| F970 battery , Type-C: 5V/1.5A DC adapter: 6-16V

Note: Due to the actual output of some batteries will be greater than 16V, it may burn out. Please make sure that the actual output voltage of the

battery used is less than 16V.

Power Consumption| <7.5W| <6.5W

HDMI Input/Output Video Format

| 480P60, 576P60     720P60/59.94/50

1080P60/59.94/50/30/29.97/25

/24/23.98       1080I60/59.94/50

HDMI Type A

| 480P60, 576P60        720P60/59.94/50

1080P60/59.94/50/30/29.97/25

/24/23.98            1080I60/59.94/50

HDMI Type A

SDI Input/Output Video Format

| 480P60, 576P60     720P60/59.94/50

1080P60/59.94/50/30/29.97/25/24/

23.98            1080I60/59.94/50

1*BNC

| 480P60, 576P60          720P60/59.94/50

1080P60/59.94/50/30/29.97/25/24/

23.98         1080I60/59.94/50

1*BNC

Frequency| 5.15-5.25GHz,5.725-5.85GH| 5.15-5.25GHz,5.725-5.85GH
Modulation Mode| OFDM| OFDM
Transmission Power| Maximum 17dBm| /
Receiving Sensitivity| /| -87dBm
Band Width| 20MHZ| 20MHZ
Latency| Min0.08S| Min0.08S
Intercom Frequency

Response Range

|

20Hz~20KHz

|

20Hz~20KHz

Operating

Temperature

| 0℃ ~ 40℃| 0℃ ~ 40℃

Storage Temperature

| -20℃ ~ 60℃| -20℃ ~ 60℃

Unit Size(mm)

| 67L24W118H (excluding antenna)| 67L24W118H (excluding antenna)
Unit Weight| 128g| 128g

FREQUENCY CHART

Device Channel WiFi Channel Frequency/MHz
1 36 5180
2 40 5200
3 44 5220
4 48 5240
5 149 5745
6 153 5765
7 157 5785
8 161 5805
9 165 5825

Common Problem

  1. The screen appears mosaic or the signal connection is unstable It means that there is a WIFI signal close to the transmission frequency, you can re-select another channel. (Note: only the receiver is allowed to adjust the channel)
  2. When the transmitter and receiver cannot be connected. Please turn off the transmitter and receiver, then turn them on again at the same time, and turn on the WPS mode to pair again.
  3. The poor WIFI reception of the mobile phone It is related to the brand and model of the mobile phone. Please try different mobile phones.

As we are improving product features and product performance, so if there is any change on the specification without prior notice.

FCC Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This Product meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement the SAR limit of USA (FCC) is1.6 W/kg averaged over one gram of this Device (FCC ID: 2A9QY-W1000S) has been tested against this SAR limit. This device was tested for typical operations 10mm from the body. To maintain compliance with FCC RF exposure requirements, 10mm separation distance should. maintained to the user’s bodies。Third-party belt- clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF Exposure requirements and should be avoided. Use only the supplied or an approved antenna.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals