somfy SITUO 5 io/RTS PURE io / RTS centralisation remote control Instruction Manual

somfy SITUO 5 io/RTS PURE io / RTS centralisation remote control

Welcomee
Thank you for choosing a Somfy product.

Who is Somfy?
Somfy develops, manufactures and sells motors and automatic control devices for domestic equipment. Drives for gates, garage doors and roller shutters, alarm systems, lighting controls, heating thermostats and all Somfy products are designed to meet your expectations in terms of safety, comfort and energy efficiency.
At Somfy, the pursuit of quality is a continuous process of improvement. Somfy’s reputation has been built upon the reliability of its products and the Somfy brand is synonymous with innovation and technological expertise worldwide.

Important information – safety

General information
Read the instructions for this product carefully. Keep these instructions. Failure to follow these instructions absolves SOMFY of all responsibility and voids the warranty. SOMFY cannot be held responsible for any changes to norms and standards that come into effect after publication of these instructions.
Check the compatibility of this product with the associated equipment and accessories. If in doubt when installing this product and/or to obtain additional information, contact a Somfy representative or visit the website www.somfy.com.

Somfy declares that the product described in these instructions, when used in accordance with these instructions, complies with the essential requirements of the applicable European directives and, in particular, with Radio Directive 2014/53/EU. The full text of the EC declaration of conformity is available at the following website: www.somfy.com/ce.

General safety instructions
Keep the product out of reach of children. Do not use abrasive products or solvents to clean it.
Use a soft, dry cloth to clean its surface. Do not knock or drop the product, expose it to flammable materials or sources of heat or moisture, or splash or immerse it. Do not attempt to repair it.

Conditions for use

The radio range is limited by radio appliance control standards.
The radio range is heavily dependent on the environment in which it is used: interference may be caused by having large-scale electrical equipment near the installation and by the type of material used in the walls and partitions.
The use of a radio appliances (e.g. a set of Hi-Fi radio headphones) operating on the same radio frequency might be detrimental to the product’s performance.

Recycling
Do not dispose of this product or its flat battery with the household waste. Please take them to a collection point or an approved centre to ensure they are recycled correctly..

PRODUCT DESCRIPTION

This remote control is a wireless transmitter equipped with RTS and io radio protocols.
It is used to control the following devices individually or simultaneously (unlimited items of equipment may be controlled by a single channel):

• RTS and io roller shutter drives,
• RTS and io hinged shutter drives,
• RTS and io remote-controlled sockets,
• RTS and io lighting micro-modules,
• RTS and io roller shutter micro-modules,
• RTS remote-controlled lamp holder.

Each channel corresponds to an individual remote control and can be used to control one or more devices.
The channel selection button is used to navigate between channels.
The indicator lights indicate the selected channel (see illustration opposite).

USE

PROGRAMMING YOUR REMOTE CONTROL ON SOMFY EQUIPMENT

Programming on a Somfy remote-controlled lamp holder or socket

Programming a remote control

1. Check that the remote-controlled lamp holder/socket is switched on.
   During this operation, disconnect all other lamp holders and sockets for Somfy remote-controlled devices in your home.

2. Press the channel selection button as many times as necessary until the indicator lights show the channel to be programmed.

3. Press the programming button on the remote-controlled lamp holder/socket until the indicator light flashes.

4. Use a fine-tipped object to make a short press on the PROG button on the back of the remote control.
   The indicator light on the remote-controlled lamp holder/socket will come on permanently, then go off.

Examples of Somfy remote-controlled lamp holders and sockets

Programming on a Somfy remote-controlled lamp holder or socket

Adding a remote control (B) using a remote control already programmed (A)

1. On the 5-channel remote control A, select the channel which controls the products you want to add to remote control B : press the channel selection button already programmed as many times as necessary .
2. Use a fine-tipped object to press the PROG button on the back of this same remote control A. The indicator lights on the associated devices will flash.
3. On 5-channel remote control B, press the channel selection button as many times as necessary until the indicator lights show the channel to be added.
4. Use a fine-tipped object to press the PROG button on the back of this same remote control B. The indicator lights on the devices to be linked come on permanently, then go out. The channel is programmed on the new remote control B.
5. If necessary, repeat this procedure with the other channels on remote control A.

This procedure requires a good knowledge of your installation.
For example, to add 2 roller shutters paired with channel 1 of remote control A to channel 5 of remote control B, if you have already programmed one of these 2 roller shutters on channel 5 of remote control B, the shutter already programmed will be deleted and the shutter not already programmed will be added.
We, therefore, advise you to add your products little by little with an individual control to avoid any deprogramming error.

Programming on a Somfy roller shutter or hinged shutter drive

You must first have commissioned your shutter drive. Before any programming, the end limits for your motor must have been set (refer to the instructions for the motor or contact Somfy assistance). Check the direction of rotation: press the button. If the shutter is lowered / closes, refer to the instructions for the motor or contact Somfy assistance.

Programming a remote control

1. Identify the original shutter control, i.e. the remote control or control point which only controls this shutter.

   • If the original control is lost or broken and it is the only one that controls the roller shutter, contact Somfy assistance.
   • If another control operates the roller shutter, use that to follow the steps below.

2. Partially open the shutter using the original control.

3. Press the PROG button on the original control until the shutter makes an up and down movement.
   The programming function is activated for 2 minutes.

4. Press the channel selection button as many times as necessary until the indicator lights show the channel to be programmed.

5. Use a fine-tipped object to make a short press on the PROG button on the back of the remote control to be added. The shutter moves up and down.

Original control

Remote control to be added

Saving or altering the favourite position
Consult the instructions relating to your shutter motor.

DELETING YOUR REMOTE CONTROL FROM SOMFY EQUIPMENT

Deleting the programmed channel from a Somfy remote-controlled lamp holder or socket

1. Check that the remote-controlled lamp holder/socket is switched on.
   During this operation, disconnect all other lamp holders and sockets for Somfy remote-controlled devices in your home.

2. Press the channel selection button as many times as necessary until the indicator lights show the channel to be deleted.

3. Press the programming button on the remote-controlled lamp holder/socket until the indicator light flashes.

4. Use a fine-tipped object to make a short press on the PROG button on the back of the remote control.
   The indicator light on the remote-controlled lamp holder/socket goes off.

Examples of Somfy remote-controlled lamp holders and sockets

DELETING YOUR REMOTE CONTROL FROM SOMFY EQUIPMENT

1. Identify the control to be retained, i.e. the remote control or control point which will continue to control this shutter and which only controls this shutter.

2. Partially open the shutter using the control to be retained.

3. Press the PROG button on the control to be retained until the shutter makes an up and down movement (or emits an audible signal).
   The programming function is activated for 2 minutes.

4. Press the channel selection button as many times as necessary until the indicator lights show the channel to be deleted.

5. Use a fine-tipped object to make a short press on the PROG button on the back of the remote control to be deleted. The shutter moves up and down (or emits 2 audible signals).

Original control

Remote control to be deleted

INSTALLING THE REMOTE CONTROL WALL MOUNTING

This product must not be installed at a height greater than 2 m.

Open the wall mounting and fix to a flat surface using a screwdriver, as shown in the diagram.

TIPS AND RECOMMENDATIONS

Specific case of an io partner solar motor (example Velux®)

Only perform this procedure to control a solar shutter motor from a partner brand other than Somfy.
This procedure must be performed for each channel of the Situo 5 io/RTS remote control to be paired with an io partner solar motor.

1. Unscrew the rear casing of the remote control.
2. Select the channel already paired or to be paired with a partner solar motor.
3. To consult the current mode: create a brief contact between the 2 parts of the dedicated activation zone (2 semi-circles beside the Prog button.).
4. Indicator light of the channel selected constantly on = standard mode.
5. Indicator light of the channel selected = mode compatible with other io partner solar motors.
6. Change mode: create a contact for approx. 2 s between the 2 parts of the dedicated activation zone until the indicator light changes status: it indicates the new mode.
7. Screw the rear cover back into place.

REPLACING THE BATTERY

Risk of explosion if the battery is replaced by an incorrect type.

1. Unscrew the rear casing of the remote control.
2. Push the battery out of its housing using a plastic object.
3. Insert a 3V CR2430 battery, with the plus (+) side visible. Make sure the polarity is correct. The power supply terminals must not be short-circuited.
4. Push the battery fully into its housing.
5. Screw the rear cover back into place.

Please separate batteries from other types of waste and recycle them via the local collection system.

TECHNICAL DATA

• Radio frequency 868.95 MHz, io-homecontrol®/ 433.42 MHz, RTS

• Frequency band and maximum power used 868.700 MHz – 869.200 MHz e.r.p. < 25 mW
  433.050 MHz – 434.790 MHz e.r.p. < 10 mW

• Radio range 150 m in free field. Use guaranteed on most floors according to the environment (point-to-point access).

• Operating temperature 0°C to + 48°C

• Power supply 1 x 3 V CR2430 battery

Installation and operating guide for io / RTS centralisation remote control – SOMFY

Somfy Gmbh
07472 / 930 – 495
www.somfy.de

Somfy Ltd.
(+44) 0113 391 3030
www.somfy.co.uk

SOMFY ACTIVITES SA
50 avenue du Nouveau Monde
74300 CLUSES
FRANCE
www.somfy.com

References

• Forum Somfy - Une question ? Un problème? Trouver de l'aide et une réponse
• Somfy: Je partner voor Smart Home oplossingen! Somfy.be
• Somfy | Motors, Automatisms, Controls & Smart Home Solutions
• Somfy.com
• Declarations of conformity
• Somfy: Motoren, Steuerungen und Smart-Home-Lösungen
• Soluciones para casas inteligentes | Somfy
• Somfy: μηχανισμοί, αυτοματισμοί, τηλεχειριστήρια και έξυπνες λύσεις για το σπίτι σας
• Somfy: motori, automazioni, controlli e soluzioni smart home
• Somfy: Je partner voor Smart Home oplossingen!
• Somfy: rozwiązania smart home i automatyka domowa
• Somfy: motores, automatismos, controlos e soluções smart home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>