VISUAL COMFORT KW 5136 Covet Small Ring Pendant Instruction Manual

VISUAL COMFORT KW 5136 Covet Small Ring Pendant

Product Information

Product Name: Covet Small Ring Pendant
Item Number: KW 5136
Installation Type: Option 1: Canopy Mounted Driver
Usage Type: Ceiling Mounted
Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.

Product Usage Instructions

Option 1: Canopy Mounted Driver

1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove mounting plate (B) from driver housing (I) and canopy (J) by removing collar ring (K).
3. Install mounting plate (B) to the junction box and secure with mounting screws (G).
4. Feed electrical wires through bottom rod (N) and thread to the junction box.
5. Connect supply ground wire (usually green or bare copper) around the green grounding screw. Tighten.
6. Continue supply ground wire and connect to filter (E) ground wire (green/yellow) using wire nut (A). Note: It is imperative that the fixture is grounded.
7. Connect filter (E) input neutral wire (white) to the supply neutral wire (usually white) using wire nut (A).
8. Connect filter (E) input hot wire (black) to the supply hot wire (usually black) using wire nut (A). Caution: Do not reverse the hot and neutral connections.
9. Connect fixture neutral wire (black) to driver (F) output wire black) using wire nut (A).
10. Connect fixture hot wire (red) to driver (F) output wire (red)using wire nut (A). Caution: Do not reverse the hot and neutral connections.
11. Make sure all wire connections are tight, then carefully tuck into the junction box.
12. Insert filter (E) and driver (F) into the center of the tall mounting plate (B).
13. Install driver housing (I) and canopy (J) to the tall mounting plate (B) and secure with collar ring (K).

Option 2: Ceiling Mounted Driver

1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove mounting plate (B) from driver housing (I) and canopy (J) by removing collar ring (K).
3. Install mounting plate (B) to the junction box and secure with mounting screws (G).
4. Feed electrical wires through bottom rod (N) and thread to the junction box.
5. Connect supply ground wire (usually green or bare copper) around the green grounding screw. Tighten.
6. Continue supply ground wire and connect to filter (E) ground wire (green/yellow) using wire nut (A). Note: It is imperative that the fixture is grounded.
7. Connect filter (E) input neutral wire (white) to the supply neutral wire (usually white) using wire nut (A).
8. Connect filter (E) input hot wire (black) to the supply hot wire (usually black) using wire nut (A). Caution: Do not reverse the hot and neutral connections.
9. Connect fixture neutral wire (black) to driver (F) output wire (black) using wire nut (A).
10. Connect fixture hot wire (red) to driver (F) output wire (red) using wire nut (A). Caution: Do not reverse the hot and neutral connections.
11. Make sure all wire connections are tight, then carefully tuck into the junction box.
12. Insert filter (E) and driver (F) into the center of the tall mounting plate (B).
13. Install driver housing (I) and canopy (J) to the tall mounting plate (B) and secure with collar ring (K).

FEATURES

ASSEMBLY INSTRUCTIONS

Option 1: Canopy Mounted Driver

Covet Small Ring Pendant
Item # KW 5136

NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED):

• Phillips Screwdriver
• Wire Strippers
• Slotted Screwdriver
• Slip-joint pliers
• Wire Cutters

1. Carefully remove all parts from the box. Place on a clean, soft surface.

2. Remove mounting plate (B) from driver housing (I) and canopy (J) by removing collar ring (K).

3. Install mounting plate (B) to the junction box and secure with mounting screws (G).

4. Feed electrical wires through bottom rod (N) and thread to connector (O). Repeat for middle rod (M), connecting to bottom rod (N).

5. Continue feeding wires through collar ring (K), canopy (J), driver housing (I) and top rod (L).

6. Holding fixture upright, slide collar ring (K), canopy (J) and driver housing (I) down bottom rods (N) and rest on connector (O). Then connect top rod (L) to middle rod (M).
   NOTE: Slide components down slowly to avoid damages.

7. Hang fixture swivel ball (H) to center of tall mounting plate (B) and secure with set screw (C) using provided screwdriver (D).
   See diagram 1.

8. Cut excess wires, being sure to leave enough to reach the junction box. Separate wires, and strip insulation on each 5/8″.

9. Connect supply ground wire (usually green or bare copper) around the green grounding screw (see diagram 2). Tighten. Continue supply ground wire and connect to filter (E) ground wire (green/yellow) using wire nut (A).
   NOTE: It is imperative that the fixture is grounded.

10. Connect filter (E) input neutral wire (white) to the supply neutral wire (usually white) using wire nut (A).

11. Connect filter (E) input hot wire (black) to the supply hot wire (usually black) using wire nut (A).
    CAUTION: Do not reverse the hot and neutral connections.

12. Connect fixture neutral wire (black) to driver (F) output wire (black) using wire nut (A).

13. Connect fixture hot wire (red) to driver (F) output wire (red) using wire nut (A).
    CAUTION: Do not reverse the hot and neutral connections.

14. Make sure all wire connections are tight, then carefully tuck into the junction box.

15. Insert filter (E) and driver (F) into center of tall mounting plate (B).

16. Install driver housing (I) and canopy (J) to tall mounting plate (B) and secure with collar ring (K).

Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.

Option 2: Ceiling Mounted Driver

TOOLS REQUIRED (NOT INCLUDED):

• Phillips Screwdriver
• Wire Strippers
• Slotted Screwdriver
• Slip-joint pliers
• Wire Cutters

1. Carefully remove all parts from the box. Place on a clean, soft surface.

2. Place driver (F) into ceiling and route all wires through one of the knockouts in the junction box.

3. Remove mounting plate (B) from driver housing (I) and canopy (J) by removing collar ring (K).
   NOTE: Driver housing (I) will be not be used for ceiling mounted assembly. Keep part and store for future use.

4. Install mounting plate (P) to the junction box and secure with mounting screws (G).

5. Feed electrical wires through bottom rod (N) and thread to connector (O). Repeat for middle rod (M), connecting to bottom rod (N).

6. Continue feeding wires through collar ring (K), canopy (J), driver housing (I) and top rod (L).

7. Holding fixture upright, slide collar ring (K), canopy (J) and driver housing (I) down bottom rods (N) and rest on connector (O). Then connect top rod (L) to middle rod (M).
   NOTE: Slide components down slowly to avoid damages.

8. Hang fixture swivel ball (H) to center of short mounting plate (P) and secure with set screw (C) using provided screwdriver (D).
   See diagram 1.
   Cut excess wires, being sure to leave enough to reach the junction box. Separate wires, and strip insulation on each 5/8″.

9. Connect supply ground wire (usually green or bare copper) around the green grounding screw (see diagram 2). Tighten. Continue supply ground wire and connect to filter (E) ground wire (green/yellow) using wire nut (A).
   NOTE: It is imperative that the fixture is grounded.

10. Connect filter (E) input neutral wire (white) to the supply neutral wire (usually white) using wire nut (A).

11. Connect filter (E) input hot wire (black) to the supply hot wire (usually black) using wire nut (A).
    CAUTION: Do not reverse the hot and neutral connections.

12. Connect fixture neutral wire (black) to driver (F) output wire (black) using wire nut (A).

13. Connect fixture hot wire (red) to driver (F) output wire (red) using wire nut (A).
    CAUTION: Do not reverse the hot and neutral connections.

14. Make sure all wire connections are tight, then carefully tuck into the junction box.

15. Install canopy (J) to short mounting plate (P) and secure with collar ring (K).

Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>