MEGA PAN T BOT Lite Tiltbot Trio User Manual

MEGA PAN T BOT Lite Tiltbot Trio

Check that the unit has not been damaged during transport

Read all cautions and warnings

prior to operation of this equipment

Protection Against Fire

1. Maintain a minimum of 2 foot distance from any type of flame.
2. For indoor use only do not expose unit to rain or moisture.
3. Replace fuse only with the specified type and rating.
4. Do not install the unit to close to a heat source.
5. Make sure cable are properly secured
6. Maximum surface operating temperature 130º.

Protection Against Electrical Fire

1. Disconnect power before servicing.
2. For connection to main power supply proceed to page 5.
3. This unit must be earthed. (electronically grounded)
4. This fixture must not be left on for long periods of time.

Protection Against Mechanical Hazards

1. Use secondary safety chain when hanging unit.
2. Use quality clamps or bolts when positioning unit
3. Do not open unit while it is on, risk of electrical shock.

What is Included

• 1pc Pan T Bot Fixture
• 1pc Power Con (type) to Nema 5-15 Cable
• 2pc Quick Connect Clamp Mounts
• 1pc User Manual

Technical Information

Part Numbers

Fixture/ Road Case
1187-Pan T Bot CAS-1187-2 2 Unit Road Case

Mechanical Specifications

• Pan Angle : 540° 8/16 bit
• Tilt Angle : 270° 8/16 bit
• DMX Connectors : Panel Mounted 3 and 5-pin XLR connectors in/out
• Artnet Connection : Panel Mounted RJ45 In and Out
• Power Connections : Panel Mounted Power Conn (Type) Power in/out connection. (Nema 5-15 to Power Conn (Type) cable included)
• Thermal : Maximum ambient temperature 104°f Maximum surface temperature 140°f
• Display : Digital
• Fastening System : 2 Quick Connect Clamp Mount
• Lens Angle : 89° RGB Emitters, 40° White Emitters

Electrical Specifications

• LED : 960 RGB 0.5 Watts / 300 White 1 Watt (6670K)
• Lumen Output : 28,595lm (All Emitters)
• Power Input : Universal 100 – 240V 50/60 Hz
• Color Rendering : 6911K (White Center Emitter Only)
• Ballast : Electronic

Power Consumption:

• Watts : 590W
• Amps : 5.04A @110V
• RDM : Yes

Control & Programming

• Protocol : DMX 512
• RDM : Yes
• DMX Channels : 2 Modes of Operation
  • Mode : 23 Ch : Pan, Pan Fine, Tilt , Tilt Fine, Pan and Tilt Speed, Dimmer, Red, Green, Blue, Strobe, Shutter Macro, Macro Speed, Color Macro, Macro Speed, Alpha numeric Display, Background Red, Background Green, Background Blue, White Dimmer, White Strobe, White Macro, Macro Speed, Control
  • Mode: 256 Ch : Pan, Pan Fine, Tilt , Tilt Fine, Pan and Tilt Speed, Control, RGB X 80, White X 10.
• Operating Mode : Stand alone 255 step dimmer setting via display Auto preprogram via display

Main Power Connection

Caution!

1. Do not connect fixture to a dimmer system.
2. This unit has Auto switching power supply. It will respond to 110V or 240V automatically
3. This unit must be earthed. (electronically grounded)
4. Replace fuse only with the specified type and rating.
5. Power Link max 3 units at 110V and 6 units at 220V.

The occupation of the connection-cable is as follows: This fixture is equipped with an electronic power supply that will let the unit operate from 100V to 240V from 50Hz to 60Hz

DMX-512 Connection

The fixture is equipped with 3 & 5 pin XLR cable mounted sockets for DMX input and output. The sockets are wired in parallel. Only use a shielded twisted pair cable designed for RS-485 3 and 5 pin XLR plugs and connectors in order to connect the controller with the fixture or the fixture with another

DMX—Input

1. Shield
2. Signal (-)
3. Signal (+)
4. N/A
5. N/A

DMX—Output

Caution!
At the last fixture the DMX signal needs to be terminated with a terminator. Solder a 120 Ohm re-sistor between the (-) and the (+) signal into a 3 or 5 pin XLR plug and plug it in to the last fixture on the signal run. Pre- manufactured terminator plugs are available for purchase from your Mega-Lite dealer (P-DMXT).

Segment Positions

Size and Weight

Main Control Menu

The control board on the fixture is your interface to access and control all the functions on the unit. Its digital display gives you a code view of the options and functions. The following will explain each function and its options

DMX Address
Press Home button. Use the up/down to select the DMX Address function press Enter to engage

Use the up/down arrows to select the desired DMX start Channel. Please con- sult your DMX Controller’s Manual to find the correct DMX Start Channel 001

Mode
Press Home button. Use the up/down to select the Mode function press Enter to engage. Select from the 2 different operating modes.

DMX DMX 23Ch Auto PRO 01 SP 90 Manual Remote

• DMX: Allows you to select from the DMX Channel control method, Linebot offers 2 control methods Standard 15 Ch and Extended 63 Ch. Please select one
• Mode: 23 Ch: Pan, Pan Fine, Tilt , Tilt Fine, Pan and Tilt Speed, Dimmer, Red, Green, Blue, Strobe, Shutter Macro, Macro Speed, Color Macro, Mac-ro Speed, Alpha numeric Display, Background Red, Background Green, Background Blue, White Dimmer, White Strobe, White Macro, Macro Speed, Control
• Mode : 256 Ch: Pan, Pan Fine, Tilt , Tilt Fine, Pan and Tilt Speed, Control, RGB X 80, White X 10
• Auto : Allows you to select from the 17 preprogram patterns that are built into the fixture. It also allows you to control the speed of those programs from 01 to 99
• Manual : Allows you to control each of the fixtures functions via the display menu. Control from 000 to 255 for each func-tion (note if fixture is powered off and back on the fixture will return to the last set mode function)
• Remote : Fixture will copy the same functions as the Main unit. (Master Fixture must be in home screen setting to en-gage)

Settings
Press Home button. Use the up/down to select the Settings function press En- ter to engage. Select from the 5 different setting options.

Artnet Display On Display Rev Off Pan Rev N Tilt Rev N DMX Fail Bl Language

• Artnet: Please follow your lighting controllers instruction for artnet connection. As each controller has different procedure for connection. (note: Fixture has a maximum 16 universe setting) For Mega Control settings please set fixture to this setting:
  IP Address

  • 002.168.052.253
  • SubNet Mask
  • 255.000.000.000
  • Net 000 Subnet 000
  • Universe 01

• Display : Display On will keep the display on for the entire time the fixtures is powered on. Display Off will auto- matically turn off the display if there is no changes after 30sec.

• Display Rev : Allows you to select from the 17 preprogram patterns that are built into the fixture. It also allows you to control the speed of those programs from 01 to 99

• Pan Rev : Inverts Pan Position

• Tilt Rev : Inverts Tilt Position

• DMX Fail : This function will allow you to set a default setting if the DMX signal is ever lost or stops working.

  • Black Out : Will set all channel to 000 and turn light off
  • Manual : Will go to the set position set on your manual display setting
  • Auto : Will go to the selected Auto Preset and speed setting set in your auto option
  • Hold : Will hold last DMX commend until a new command signal is received

• Language : Select ether English or Chinese

System Info
Press Home button. Use the up/down to select the System Info function press Enter to engage. Receive information on 3 different parameters

• Firmware : Gives you information on the software version being used in the fixture.
• Time Info : Provides information on the fixture usage, by counting the hours the fixture is powered on
• Temp : Gives you fixture internal temperature information

DMX Profile

Pan T Bot 23Channel Mode

10

| | No Function| 0-1|

0

| Strobe (slow to fast)| 2-127
Strobe| Strobe Pulse (slow to fast)| 128-170
RGB| Random Strobe All (slow to fast)| 171-213
| Random 1-80 Strobe (slow to fast)| 214-255

11

| | No Function| 0-1|

0

| Macro 1| 2-12
| Macro 2| 13-23
| Macro 3| 24-34
| Macro 4| 35-45
| Macro 5| 46-56
| Macro 6| 57-67
| Macro 7| 68-78
| Macro 8| 79-89
| Macro 9| 90-100
| Macro 10| 101-111
Shutter Macro| Macro 11| 112-122
(Select Color)| Macro 12| 123-133
| Macro 13| 134-144
| Macro 14| 145-155
| Macro 15| 156-166
| Macro 16| 167-177
| Macro 17| 178-188
| Macro 18| 189-199
| Macro 19| 200-210
| Macro 20| 211-221
| Macro 21| 222-232
| Macro 22| 232-255
12| Macro Speed| Shutter Macro Speed (slow to fast)| 0-255| 0

13

|

Multy Color Macro

| No Function| 0-1|

0

Macro 1| 2-12
Macro 2| 13-23
Macro 3| 24-34
Macro 4| 35-45
Macro 5| 46-56
Macro 6| 57-67
Macro 7| 68-78
Macro 8| 79-89
Macro 9| 90-100
Macro 10| 101-111
Macro 11| 112-122
Macro 12| 123-133
Macro 13| 134-144
Macro 14| 145-155
Macro 15| 156-166
Macro 16| 167-177
Macro 17| 178-188
Macro 18| 189-199
Macro 19| 200-210
Macro 20| 211-221
Macro 21| 222-232
Macro 22| 232-255
14| Macro Speed| Color Macro Speed (slow to fast)| 0-255| 0

15

| | No Function| 0-1|

0

---|---|---|---|---
| 0| 2-6
| 1| 7-12
| 2| 13-18
| 3| 19-24
| 4| 25-30
| 5| 31-36
| 6| 37-52
| 7| 43-48
| 8| 49-54
| 9| 55-60
| A| 61-66
| B| 67-72
| C| 73-78
| D| 79-84
| E| 85-90
| F| 91-96
| G| 97-102
| H| 103-108
Alpha Numeric| I| 109-114
Display| J| 115-120
| K| 121-126
| L| 127-132
| M| 133-138
| N| 139-144
| O| 145-150
| P| 151-156
| Q| 157-162
| R| 163-168
| S| 169-174
| T| 175-180
| U| 181-186
| V| 187-192
| W| 193-198
| X| 199-204
| Y| 205-210
| Z| 211-216
| Right Arrow| 217-222
| Down Arrow| 223-228
| Up Arrow| 229-234
| Left Arrow| 235-255
16| Back Red| Background Red| 0-255| 0
17| Back Green| Background Green| 0-255| 0
18| Back Blue| Background Blue| 0-255| 0
19| White Dimmer| White| 0-255| 255

20

|

Strobe

| No Function| 0-1|

0

Strobe (slow to fast)| 2-127
Strobe Pulse (slow to fast)| 128-170
Random Strobe All (slow to fast)| 171-213
Random 1-10 Strobe (slow to fast)| 214-255

21

| | No Function| 0-1|

0

| Macro 1| 2-19
| Macro 2| 20-39
| Macro 3| 40-59
| Macro 4| 60-89
White Macro| Macro 5| 90-109
(Responds to| Macro 6| 110-139
White Dimmer)| Macro 7| 140-159
| Macro 8| 160-189
| Macro 9| 190-209
| Macro 10| 210-239
| Macro 11| 240-255
22| Macro Speed| White Macro Speed (slow to fast)| 0-255| 0
23| Control| No Function| 0-127| 0
Reset| 128-255

Pan T Bot 256 Ch Mode

Item List

Rigging the Fixture

Caution!

1. The installations must be carried out by an authorized dealer or trained professional.
2. Unit may cause severe injuries if you have doubts concerning the safety do not install.
3. Unit is to be 24inches away from flammable materials (decoration material)
4. Use high quality installation equipment to hang unit

When rigging a unit it is very important that you follow common safety procedures. Rigging requires extensive experi-ence including but not limited to calculating working loads, material being used and periodic safety inspections. If you lack these qualifications, do not attempt the installation yourself, instead use a professional structural rigger.
When rigging the unit always be secured with a secondary safety attachment. The installation location of the projector has got to be built in the way that it can hold 10 times the weight for 1 hour with out any harming. Installation should be checked at least once a year by a skilled person

Unit can be installed in any of these directions

Cleaning and Maintenance

Installation Maintenance : The operator has to make sure that the unit is operating safely and has the installations and electronics checked by an expert every 2 years

The following points have to be considered during the inspection:

1. All screws used for installing the device or part of the device have to be tightly connected and must not be corroded.
2. There must not be any deformations on the housing, fixation and installation spots (ceiling, suspension, trussing).
3. The electronic power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments. Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed

Note: There is no serviceable parts inside the device. Maintenance and service operations are to be carried out by au-thorized dealers.

Replacing the fuse: When possible only replace the fuse with the same type and rating.

Replacing the power cable : If the power cable of this device becomes damaged, it has to be replaced by authorized dealers or trained professional only. Should you have further questions , please contact your dealer

MEGA Systems, Inc. Warranty

MEGA SYSTEMS INC (“MSI) hereby warrants to the original purchaser/owner (‘Customer), MSI products to be free of manufacturing defects in material and workmanship, tor the warranty periods as defined below from the original purchase invoice date. I his warranty applies exclusively to new MSI branded andlor distributed products listed below, purchased from an MSl AUTHORIZED dealer/ reseller. This warranty is not transferable and may or may not apply to products sold and/or forwarded outside the United States. Please contact MSI for applicable regional product warranty information. The purchase of MS product constitutes the Customer’s acceptance of all warranty terms and conditions as listed in this limited warranty statement This warranty provides the Customer with legal rights, which may vary from state to state. Please contact MSI regarding warranty questions prior to purchasing

All warranty claims are evaluated under the terms of this limited waranty. If a product falls within the warranty period and if, upon examination by MSl it is found to have tailed for a covered cause, MSI will, at ts sole discretion, repair or replace the defective part or product or reimburse the purchaser a pro-rated portion of the purchase price based on the percentage of the warranty period still remaining as of the date that the returned product was received by MSI. Should a replacement part or product be discontinued or unavallable, MS reserves the nght, in ts sole and absolute discretion, to substitute a comparable replacement part or product for the defective pat or product. MSI warranty obligation hereunder is limited solely to the repair or replacement of or reimbursement tor the particular parts or products determined by MSI to have Tailed for a covered cause within the warranty period.

In no event shall MSI be responsible to replace or reimburse purchaser for any products or portions of a system that MsI determines has not failed for a covered cause within the warranty period, even it such other productsS or portions of a system are used together with products being repaired or replaced by MSI under this warranty and the repaired product difers in brightness, colors or any other attribute after the repai. Costs of removal, shipping to MSI or its authorized representative and reinstallation are solely the respon sibility of the purchaser. If MSI determines that the product is covered by this imited warranty, It WIl only pay tor parts and labor as Indicated Dy product type. IT Ms determines that the product is not covered by thiS limited warranty, the purcnaser will nave the option ot paying Tor the repair (IT the product can be repaired) and the purcnaser shall be responsible Tor the cost or shipping the repaired pr0duct back TO the purchaser. MSI reserves the rignt, In is sole and absoure aiscreuon, to decline any repair.

IN NO EVENT SHALL MEGA SYSTEMS, INC. BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, INDIRECT OR PUNITIVE LOSS OR
DAMAGE OF ANY KIND, INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS OR REVENUES, LOSS OF USE OF THE PRODUCT OR ANY OTHER GOODS OR ASSOCIATED EOUIPMENT, DAMAGE TO ANY ASSOCIATED EQUIPMENT, COST OF CAPITAL, COST OF SUBSTITUTE PRODUCTS, FACILITIES OR SERVICES, DOWN TIME COST, INSTALLATION OR LABOR cOSTS, OR CLAIMS OF THE PURCHASER’S CUSTOMERS, WHETHER BASED ON WARRANTY, CONTRACT OR NEGLIGENCE, ARISING IN CONNECTION WITH THE SALE, USE OR REPAIR OF THE PRODUCT. MEGA SYSTEMS INC’S MAXIMUM LIABILITY SHALL NOT, IN ANY CASE, EXCEED THE PURCHASE PRICE OF THE PRODUCT THAT GIVES RISE TO THE CLAIM. EXCEPT FOR THE LIMITED WARRANTY SET FORTH HEREIN, ALL PRODUCTS SOLD BY MEGA SYSTEMS, INC. ARE SOLD “AS IS’ WITHOUT ANYWARRANTY, EXPRESS OR IMPLIED, STATUTORY OR OTHERWISE, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTCULAR PURPOSE, ALL OF WHICH ARE EXPRESSLY AND SPECIFICALLY DISCLAIMED BY MEGA SYSTEMS, INC.

Customer Support

Mega Lite has a customer support line to provide set up help and to answer any question should you encounter a prob-lem. Please visit our website for any other related technical documents. For service related issue please contact our service dept.

• Monday—Friday 9am to 6pm CST
• Phone : 210-684-2600
• E-mail : service@mega.lighting

Manual Version
Please Visit www.mega.lighting for the most up to date manual version

• Document Version 1.0
• Date 01/10/2023
• Fixture Software V1.0
• Notes

Mega-Lite 18668 Highway 16N Helotes, Texas 78023 Ph 210-684-2600 Fax 210-855-6279 www.mega.lighting / info@mega.lighting

References

• Concert Touring Lighting | Lighting Consoles - MEGA-LITE

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>