Allen-Bradley 1734-IV2 POINT I-O Source Input Modules Instruction Manual

Allen-Bradley 1734-IV2 POINT I-O Source Input Modules

Product Information

The POINT I/O Source Input Modules are a series of modules designed for input signal acquisition in industrial automation systems. They are available in various catalog numbers, including 1734-IV2, 1734-IV4, 1734-IV8, and 1734-IV8K (conformal coated version). The series is currently in its C version.

Summary of Changes:

• Updated IEC Hazardous Location Approval
• Updated UK and European Hazardous Location Approval
• Updated Special Conditions for Safe Use
• Updated General Specifications
• Updated Environmental Specifications
• Updated Certifications

This publication contains the following new or updated information. This list includes substantive updates only and is not intended to reflect all changes.

Environment and Enclosure **

**

The equipment has North American Hazardous Location Approval and IEC Hazardous Location Approval. When operating in a hazardous location, the equipment must be mounted in a suitable enclosure with proper wiring methods that comply with the governing electrical codes. The equipment also has UK and European Hazardous Location Approval. Special conditions for safe use and precautions against electrostatic discharge are provided.

ATTENTION: This equipment is intended for use in a Pollution Degree 2 industrial environment, in overvoltage Category II applications (as defined in EN/IEC 60664-1), at altitudes up to 2000 m (6562 ft) without derating.
This equipment is not intended for use in residential environments and may not provide adequate protection to radio communication services in such environments. This equipment is supplied as open-type equipment for indoor use. It must be mounted within an enclosure that is suitably designed for those specific environmental conditions that will be present and appropriately designed to prevent personal injury resulting from accessibility to live parts. The enclosure must have suitable flame-retardant properties to prevent or minimize the spread of flame, complying with a flame spread rating of 5VA or be approved for the application if nonmetallic. The interior of the enclosure must be accessible only by the use of a tool. Subsequent sections of this publication may contain more information regarding specific enclosure type ratings that are required to comply with certain product safety certifications. In addition to this publication, see the following:

• Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1, for additional installation requirements.
• NEMA Standard 250 and EN/IEC 60529, as applicable, for explanations of the degrees of protection provided by enclosures.

ATTENTION: Read this document and the documents listed in the Additional Resources section about installation, configuration, and operation of this equipment before you install, configure, operate, or maintain this product. Users are required to familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards.
Installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried out by suitably trained personnel in accordance with applicable code of practice. In case of malfunction or damage, no attempts at repair should be made. The module should be returned to the manufacturer for repair. Do not dismantle the module.

North American Hazardous Location Approval

The Following Information Applies When Operating This Equipment In Hazardous Locations. Products marked “CL I, DIV 2, GP A, B, C, D” are suitable for use in Class I Division 2 Groups A, B, C, D, Hazardous Locations and nonhazardous locations only. Each product is supplied with markings on the rating nameplate indicating the hazardous location temperature code. When combining products within a system, the most adverse temperature code (lowest “T” number) may be used to help determine the overall temperature code of the system. Combinations of equipment in your system are subject to investigation by the local Authority Having Jurisdiction at the time of installation.

WARNING:
Explosion Hazard

• Do not disconnect equipment unless power has been removed or the area is known to be nonhazardous.
• Do not disconnect connections to this equipment unless power has been removed or the area is known to be nonhazardous. Secure any external connections that mate to this equipment by using screws, sliding latches, threaded connectors, or other means provided with this product.
• Substitution of components may impair suitability for Class I, Division 2.

WARNING: When used in a Class I, Division 2, hazardous location, this equipment must be mounted in a suitable enclosure with proper wiring method that complies with the governing electrical codes.

IEC Hazardous Location Approval
The following applies to products marked with IECEx certification:

• Are intended for use in areas in which explosive atmospheres caused by gases, vapors, mists, or air are unlikely to occur, or are likely to occur only infrequently and for short periods. Such locations correspond to Zone 2 classification to IEC 60079-0.
• The type of protection is Ex eC IIC T4 Gc according to IEC 60079-0 and IEC 60079-7.
• Comply to Standards IEC 60079-0, Explosive atmospheres ‐ Part 0: Equipment ‐ General requirements, Edition 7, Revision Date 2017 and IEC 60079-7, 5.1 Edition revision date 2017, Explosive atmospheres – Part 7: Equipment protection by increased safety “e”, reference IECEx certificate number IECEx UL 20.0072X.
• May have catalog numbers followed by a “K” to indicate a conformal coating option.

UK and European Hazardous Location Approval

The following applies to products marked II 3 G:

• Are intended for use in potentially explosive atmospheres as defined by UKEX regulation 2016 No. 1107 and European Union Directive 2014/34/EU and has been found to comply with the Essential Health and Safety Requirements relating to the design and construction of Category 3 equipment intended for use in Zone 2 potentially explosive atmospheres, given in Schedule 1 of UKEX and Annex II of this Directive.

• Compliance with the Essential Health and Safety Requirements has been assured by compliance with EN IEC 60079-7, and EN IEC 60079-0.

• Are Equipment Group II, Equipment Category 3, and comply with the Essential Health and Safety Requirements relating to the design and construction of such equipment given in Schedule 1 of UKEX and Annex II of EU Directive 2014/34/EU. See the UKEx and EU Declaration of Conformity at rok.auto/certifications for details.

• The type of protection is Ex ec IIC T4 Gc according to EN IEC 60079-0:2018, EXPLOSIVE ATMOSPHERES – PART 0: EQUIPMENT – GENERAL REQUIREMENTS, Issue Date 07/2018, and CENELEC EN IEC 60079-7:2015+A1:2018, Explosive atmospheres. Equipment protection by increased safety “e”.

• Comply to Standard EN IEC 60079-0:2018, EXPLOSIVE ATMOSPHERES – PART 0: EQUIPMENT – GENERAL REQUIREMENTS, Issue Date 07/2018, and CENELEC EN IEC 60079-
  7:2015+A1:2018 Explosive atmospheres. Equipment protection by increased safety “e”, reference certificate number DEMKO 04 ATEX 0330347X and UL22UKEX2478X.

• Are intended for use in areas in which explosive atmospheres caused by gases, vapors, mists, or air are unlikely to occur, or are likely to occur only infrequently and for short periods. Such locations correspond to Zone 2 classification according to UKEX regulation 2016 No. 1107 and ATEX directive 2014/34/EU.

• May have catalog numbers followed by a “K” to indicate a conformal coating option.

WARNING:

• This equipment is not resistant to sunlight or other sources of UV radiation.
• This equipment shall be mounted in an UKEX/ATEX/IECEx Zone 2 certified enclosure with a minimum ingress protection rating of at least IP54 (in accordance with EN/IEC 60079-0) and used in an environment of not more than Pollution Degree 2 (as defined in EN/IEC 60664-1) when applied in Zone 2 environments. The enclosure must be accessible only by the use of a tool.
• This equipment shall be used within its specified ratings defined by Rockwell Automation.
• Provision shall be made to prevent the rated voltage from being exceeded by transient disturbances of more than 140% of the peak rated voltage when applied in Zone 2 environments.
• The instructions in the user manual shall be observed.
• This equipment must be used only with UKEX/ATEX/IECEx certified Rockwell Automation backplanes.
• Earthing is accomplished through mounting of modules on rail.
• Devices shall be used in an environment of not more than Pollution Degree 2.

Special Conditions for Safe Use

ATTENTION:

• This product is grounded through the DIN rail to chassis ground. Use zinc plated chromate-passivated steel DIN rail to assure proper grounding. The use of other DIN rail materials (for example, aluminum or plastic) that can corrode, oxidize, or are poor conductors, can result in improper or intermittent grounding. Secure DIN rail to mounting surface approximately every 200 mm (7.8 in.) and use end-anchors appropriately. Be sure to ground the DIN rail properly. See Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1, for more information.
• Transient protection shall be provided that is set at a level not exceeding 140% of the peak rated voltage at the supply terminals to the equipment.
• Do not remove or replace an adapter while power is applied. Interruption of the backplane can result in unintentional operation or machine motion.
• Do not discard the end cap. Use this end cap to cover the exposed interconnections on the last mounting base on the DIN rail. Failure to do so could result in equipment damage or injury from electric shock.
• If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.

Prevent Electrostatic Discharge

• ATTENTION: This equipment is sensitive to electrostatic discharge, which can cause internal damage and affect normal operation. Follow these guidelines when you handle this equipment:
• Touch a grounded object to discharge potential static.
• Wear an approved grounding wrist strap.
• Do not touch connectors or pins on component boards.
• Do not touch circuit components inside the equipment.
• Use a static-safe workstation, if available.
• Store the equipment in appropriate static-safe packaging when not in use.

Electrical Safety Considerations

ATTENTION:

• This equipment is certified for use only within the surrounding air temperature range of -20…+55 °C (-4…+131 °F). The equipment must not be used outside of this range.
• Use only a soft dry anti-static cloth to wipe down equipment. Do not use any cleaning agents.

Before You Begin

You can use these Series C POINT I/O™ Input modules with Device Net® and PROFIBUS adapters. If you are using Studio 5000 Logix Designer® application version 20 or higher, you can also use the modules with ControlNet® and EtherNet/IP™ adapters. See Figure 1 to identify the external features of the module.

POINT I/O Input Module with 1734-TB or 1734-TBS Base

The wiring base assembly includes terminal base, 1734-TB, or 1734-TBS, which consists of a mounting base, 1734-MB, and removable terminal block, 1734-RTB, or 1734-RTBS.

| Description| | Description
---|---|---|---
1| Module locking mechanism| 6| 1734-TB or 1734-TBS mounting base
2| Slide-in writable label| 7| Interlocking side pieces
3| Insertable I/O module| 8| Mechanical keying (orange)
4| Removable terminal block (RTB) handle| 9| DIN rail locking screw (orange)
5| Removable terminal block with screw (1734-RTB) or spring clamp (1734-RTBS)| 10| Module wiring diagram

The installation process involves several steps:

1. Install the Mounting Base
2. Install the Module
3. Install the Removable Terminal Block
4. Remove a Mounting Base
5. Wire the Module
6. Communicate with the Module
7. Interpret Status Indicators

Specifications **

**

The product specifications include details about the equipment’s features, capabilities, and performance. Refer to the user manual for more information.

POINT I/O Source Input Modules – 1734-IV2, 1734-IV4, 1734-IV8, 1734-IV8K

Attribute| 1734- IV2| 1734- IV4| 1734-IV8, 1734-IV8K
---|---|---|---
Number of inputs, sourcing| 2 (1 group of 2)| 4 (1 group of 4)| 8 (1 group of 8)
Voltage, on-state Min
Nom Max| 10V DC
24V DC
28.8V DC
Current, on-state Min
Nom Max| 2 mA
4 mA @ 24V DC
5 mA
Voltage, off-state, max| 5V DC
Current, off-state, min| 1.5 mA
Impedance, input, Nom
Max| 3.6 kΩ
4.7 kΩ
Input filter time(1) Off to On
On to Off| 0.5 hardware plus 0…63 ms (user selectable)
0.5 hardware plus 0…63 ms (user selectable)
Field wiring terminations| 0 – Input 0
1– Input 1
2 – No connection
3 – No connection
4 – Common
5 – Common
6 – User supply
7 – User supply| 0 – Input 0
1– Input 1
2 – Input 2
3 – Input 3
4 – Common
5 – Common
6 – User supply
7 – User supply| 0 – Input 0
1– Input 1
2 – Input 2
3 – Input 3
4 – Input 4
5 – Input 5
6 – Input 6
7 – Input 7

1. Input Off-to-On filter time is the time from a valid input signal to recognition by the module. Input On-to-Off time is the time from a valid input signal to recognition by the module.

General Specifications

Attribute| 1734- IV2| 1734- IV4| 1734-IV8, 1734-IV8K
---|---|---|---
Terminal base screw torque| 0.8 N•m (7 lb•in)
**** Indicators| 1 green/red – module status indicator, logic side 1 green/red – network status indicator, logic side
2 yellow – input status indicators, logic side| 4 yellow – input status indicators, logic side| 8 yellow – input status indicators, logic side
Module location| 1734-TB or 1734-TBS wiring base assembly
POINT Bus™ current, max| 75 mA @ 5V DC
---|---
Power dissipation, max| 0.7 W @ 28.8V DC| 1.0 W @ 28.8V DC| 1.6 W @ 28.8V DC
Thermal dissipation, max| 2.4 BTU/h @ 28.8V DC| 3.4 BTU/h @ 28.8V DC| 5.5 BTU/h @ 28.8V DC
Isolation voltage| 50V continuous
Tested to withstand 2500V DC for 60 s
Field power bus Supply voltage, nom Voltage range| 24V DC
10 28.8V DC
Dimensions, approx (H x W x D)| 56 x 12 x 75.5 mm
(2.21 x 0.47 x 2.97 in.)
Wiring category(1)| 2 – on signal ports
Wire size| 0.25…2.5 mm2 (22…14 AWG) solid or stranded shielded copper wire rated at 75 °C (167 °F) or greater 1.2 mm (3/64 in.) insulation max
Weight, approx.| 31.2 g (1.10 oz)| 31.8 g (1.12 oz)| 32.3 g (1.14 oz)
Enclosure type rating| None (open-style)
North American temp code| T4A
IECEx temp code| T4| –
UKEX/ATEX temp code| T4| –
Key switch position| 1

1. Use this Conductor Category information for planning conductor routing as described in the appropriate System Level Installation Manual. Also see Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1, for more information.

Environmental Specifications

IEC 60068-2-2 (Test Bd, operating dry heat),
IEC 60068-2-14 (Test Nb, operating thermal shock):
-20 °C ≤ Ta ≤ +55 °C (-4 °F ≤ Ta ≤ + 131 °F)
**** Temperature, storage| IEC 60068-2-1 (Test Ab, unpackaged nonoperating cold),
IEC 60068-2-2 (Test Bb, unpackaged nonoperating dry heat),
IEC 60068-2-14 (Test Na, unpackaged nonoperating thermal shock):
-40…+85 °C (-40…+185 °F)
Temperature, surrounding air, max| 55 °C (131 °F)
Relative humidity| IEC 60068-2-30 (Test Db, unpackaged damp heat): 5…95% noncondensing
Vibration| IEC60068-2-6 (Test Fc, operating): 5 g @ 10…500 Hz
Shock, operating| IEC 60068-2-27 (Test Ea, unpackaged shock): 30 g
Shock, nonoperating| 50 g
Emissions| IEC 61000-6-4
ESD immunity| IEC6100-4-2:
6 kV contact discharges 8 kV air discharges
Radiated RF immunity| IEC 61000-4-3:
10V/m with 1 kHz sine-wave 80% AM from 80…6000 MHz
EFT/B immunity| IEC 61000-4-4:
±2 kV at 5 kHz on power ports
±2 kV at 5 kHz on signal ports
Surge transient immunity| IEC 61000-4-5: ±1 kV line-line(DM) and ±2 kV line- earth (CM) on signal ports
Conducted RF immunity| IEC61000-4-6:
10V rms with 1 kHz sine-wave 80% AM from 150 kHz…80 MHz

Installation Instructions:
Before installing, configuring, or performing maintenance on the product, read the user manual and other listed documents regarding installation, configuration, and operation. Users must also comply with applicable laws, codes, and standards. Ensure that the equipment is used as specified by the manufacturer to ensure proper functioning and protection. For specific installation instructions, refer to Figure 1 in the user manual. The wiring base assembly consists of a terminal base (1734-TB or 1734-TBS), a mounting base (1734-MB), and a removable terminal block (1734-RTB or 1734-RTBS). Refer to the user manual for detailed descriptions of the module components and their functions.

POINT I/O Source Input Modules

Catalog Numbers 1734-IV2, 1734-IV4, 1734-IV8, 1734-IV8K, Series C Catalog numbers with the suffix ‘K’ are conformal coated and their specifications are the same as non-conformal coated catalogs.

ATTENTION: Read this document and the documents listed in the Additional Resources section about installation, configuration and operation of this equipment before you install, configure, operate or maintain this product. Users are required to familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards.
Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried out by suitably trained personnel in accordance with applicable code of practice. If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.

Install the Mounting Base
To install the mounting base on the DIN rail, proceed as follows:

1. Position the mounting base vertically above the installed units (adapter, power supply, or existing module).
2. Slide the mounting base down allowing the interlocking side pieces to engage the adjacent module or adapter.
3. Press firmly to seat the mounting base on the DIN rail. The mounting base snaps into place. Be sure that the orange DIN rail locking screw is in the horizontal position and that it has engaged the DIN rail.

Install the Module

The module can be installed before or after base installation. Make sure that the mounting base is correctly keyed before installing the module into the mounting base. In addition, make sure that the mounting base locking screw is positioned horizontal referenced to the base.

ATTENTION: When you insert or remove the module while backplane power is on, an electrical arc can occur. This could cause an explosion in hazardous location installations.
Be sure that power is removed or the area is non-hazardous before proceeding. Repeated electrical arcing causes excessive wear to contacts on both the module and its mating connector. Worn contacts may create electrical resistance that can affect module operation.

1. Using a bladed screwdriver, rotate the key switch on the mounting base clockwise until the number required for the type of module being installed aligns with the notch in the base.
2. Verify that the DIN rail locking screw is in the horizontal position. You cannot insert the module if the locking mechanism is unlocked.
3. Insert the module straight down into the mounting base.
4.  Press to secure. The module locks into place.

ATTENTION: Do not discard the end cap. Use this end cap to cover the exposed interconnections on the last mounting base on the DIN rail. Failure to do so could result in equipment damage or injury from electric shock.

Install the Removable Terminal Block

A Removable Terminal Block (RTB) is supplied with your wiring base assembly. To remove, pull up on the RTB handle. This allows the mounting base to be removed and replaced as necessary without removing any of the wirings. To reinsert the Removable Terminal Block, proceed as follows.
WARNING: When you connect or disconnect the Removable Terminal Block (RTB) with field-side power applied, an electrical arc can occur. This can cause an explosion in hazardous location installations.
Be sure that power is removed or the area is nonhazardous before proceeding.

1. Insert the end opposite the handle into the base unit. This end has a curved section that engages with the wiring base.
2. Rotate the terminal block into the wiring base until it locks itself in place.
3. If an I/O module is installed, snap the RTB handle into place on the module.

WARNING: For 1734-RTBS and 1734-RTB3S, to latch and unlatch the wire, insert a bladed screwdriver (catalog number 1492-N90 – 3 mm diameter blade) into the opening at approximately 73° (blade surface is parallel with top surface of the opening) and push up gently.

WARNING: For 1734-TOPS and 1734-TOP3S, to latch and unlatch the wire, insert a bladed screwdriver (catalog number 1492-N90 – 3 mm diameter) into the opening at approximately 97° (blade surface is parallel with top surface of the opening) and press in (do not push up or down).

Remove a Mounting Base
To remove a mounting base, you must remove any installed module and the module that is installed in the base to the right. Remove the removable terminal block, if wired.

1. Unlatch the RTB handle on the I/O module.
2. Pull on the RTB handle to remove the removable terminal block.
3. Press the module lock on the top of the module.
4. Pull on the I/O module to remove from the base.
5. Repeat steps 1, 2, 3 and 4 for the module to the right.
6. Use a small bladed screwdriver to rotate the orange base locking screw to a vertical position. This releases the locking mechanism.
7. Lift straight up to remove.

Wire the Module

To wire the module, see the diagrams and tables.

Input = 0 and 1
NC = No connection (2 and 3)
C = Common (4 and 5)
V = Supply (6 and7)

Input 0, 1, 2, and 3
C = Common (4 and 5)
V = Supply (6 and7)

Input 0, 1, 2, 3, 4, 5, 6, and 7
Note: V and C are daisy chained from either the adapter, 1734-FPD, 1734-EP24DC, or from a user supplied auxiliary terminal block.
WARNING: If you connect or disconnect wiring while the field-side power is on, an electrical arc can occur. This could cause an explosion in hazardous location installations. Be sure that power is removed or the area is nonhazardous before proceeding.

POINT I/O Source Input Module Wiring – 1734-IV2

C = Common
V = 12/24V DC supply
Note: Not protected, 0.3A max

Connect power on 3-wire proximity switches.
12/24V DC is provided by the internal field power bus.

POINT I/O Source Input Module Wiring – 1734-IV4

C = Common
V = 12/24V DC supply
Note: Not protected, 0.3A max

Connect power on 3-wire proximity switches.
12/24V DC is provided by the internal field power bus.

POINT I/O Source Input Module Wiring – 1734-IV8, 1734-IV8K

C = Common
V = 12/24V DC supply

Daisy chain common and power connections from 1734 adapter, 1734-FPD, 1734-EP24DC, or from user supplied external auxiliary terminal block.

Wiring Example of 1734-IV8, 1734-IV8K Using 2-Wire Proximity Switches

Terminal block with bus connector strip

Wiring Example of 1734-IV8, 1734-IV8K Using 3-Wire Proximity Switches

Communicate with the Module

POINT I/O modules send (produce) and receive (consume) I/O data (messages). You map this data into the memory of the processor.
The 1734-IV2, 1734-IB4, and 1734-IV8 modules produce 1 byte of input data (scanner Rx). The modules do not consume I/O data (scanner Tx).
Message Size: 1 Byte

| 7| 6| 5| 4| 3| 2| 1| 0
---|---|---|---|---|---|---|---|---
Produces (Rx)| | | | | | | I1| I0
Consumes (Tx)| No consumed data

Interpret Status Indicators

See Figure 7 and Table 1 for information on how to interpret the status indicators.

Status Indicators for POINT I/O 2 Current Output and 2 Voltage Output Analog Modules

Indicator Status for Modules

| Status| Description
---|---|---

Module status

| Off| No power applied to device.
Green| Device operating normally.
Flashing green| Device needs commissioning due to missing, incomplete, or incorrect configuration.
Flashing red| Recoverable fault.
Red| Unrecoverable fault – may require device replacement.
Flashing red/green| Device is in self-test mode.
Network status| Off| Device is not online:

•  Device has not completed dup_MAC-id test.
• Device not powered – check module status indicator.

Flashing green| Device is online but has no connections in the established state.
Green| Device is online and has connections in the established state.
Flashing red| One or more I/O connections are in timed-out state.
Red| Critical link failure – failed communication device. Device detected error that prevents it from communicating on the network.
Flashing red/green| Communication faulted device – the device has detected a network access error and is in communication faulted state. Device has received and accepted an Identity Communication Faulted Request – long protocol message.
Channel status| Off| Input is in the Off state.
Yellow| Input is in the On state.

Certifications

See UL File E65584. UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations, certified for U.S. and Canada. See UL File E194810.
UK and CE| UK Statutory Instrument 2016 No. 1091 and European Union 2014/30/EU EMC Directive, compliant with: EN 61326-1; Measurement/Control/Laboratory use, Industrial requirements
EN 61000-6-2; Industrial Immunity EN 61000-6-4; Industrial Emissions
EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
UK Statutory Instrument 2012 No. 3032 and European Union 2011/65/EU RoHS, compliant with: EN IEC 63000; Technical documentation
Ex| For 1734-IV2 and 1734-IV4 only
UK Statutory Instrument 2016 No. 1107 and European Union 2014/34/EU ATEX Directive, compliant with: EN IEC 60079-0; General Requirements
EN IEC 60079-7; Explosive Atmospheres, Protection “e” II 3 G Ex ec IIC T4 Gc
DEMKO 04 ATEX 0330347X UL22UKEX2478X
IECEx| For 1734-IV2 and 1734-IV4 only
IECEx System, compliant with:
IEC 60079-0; General Requirements
IEC 60079-7; Explosive Atmospheres, Protection “e” II 3 G Ex ec IIC T4 Gc
IECEx UL 20.0072X
KC| Korean Registration of Broadcasting and Communications Equipment, compliant with: Article 58-2 of Radio Waves Act, Clause 3
RCM| Australian Radiocommunications Act, compliant with: AS/NZS CISPR 11; Industrial Emissions.
Morocco| Arrêté ministériel n° 6404-15 du 29 ramadan 1436
** CCC| For 1734-IV2 and 1734-IV4 only
** CNCA-C23-01 䔂ⵖ䚍❡ㅷ雩霆㹊倶錞ⴭ 旘歏孞
CNCA-C23-01 CCC Implementation Rule Explosion-Proof Electrical Products
CCC: 2020122309111607
EAC| Russian Customs Union TR CU 020/2011 EMC Technical Regulation

1. See the Product Certification link at rok.auto/certifications for Declaration of Conformity, Certificates, and other certification details.

Rockwell Automation Support
Use these resources to access support information.

Technical Support Center| Find help with how-to videos, FAQs, chat, user forums, Knowledgebase, and product notification updates.| rok.auto/support
---|---|---
Local Technical Support Phone Numbers| Locate the telephone number for your country.| rok.auto/phonesupport
Technical Documentation Center| Quickly access and download technical specifications, installation instructions, and user manuals.| rok.auto/techdocs
Literature Library| Find installation instructions, manuals, brochures, and technical data publications.| rok.auto/literature
Product Compatibility and Download Center (PCDC)| Download firmware, associated files (such as AOP, EDS, and DTM), and access product release notes.| rok.auto/pcdc

Documentation Feedback
Your comments help us serve your documentation needs better. If you have any suggestions on how to improve our content, complete the form at rok.auto/docfeedback.

Waste Electrical and Electronic Equipment (WEEE)

• At the end of life, this equipment should be collected separately from any unsorted municipal waste.

Rockwell Automation maintains current product environmental compliance information on its website at rok.auto/pec.

Allen-Bradley, expanding human possibility, FactoryTalk, POINT I/O, POINTBus, Rockwell Automation, Studio 5000 Logix Designer, and TechConnect are trademarks of Rockwell Automation, Inc. ControlNet, DeviceNet, and EtherNet/IP are trademarks of ODVA, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies. Publication 1734-IN052H-EN-E – September 2022 | Supersedes Publication 1734-IN052G-EN-E – January 2021
Copyright © 2022 Rockwell Automation, Inc. All rights reserved.

References

• Product Certifications | Rockwell Automation
• Publication Feedback Form | Rockwell Automation
• Literature Library | Rockwell Automation
• Product Compatibility & Download Center from Rockwell Automation
• Product Environmental Compliance | Rockwell Automation
• Phone/Onsite Support
• Support | Rockwell Automation
• Technical Documentation Center | Rockwell Automation
• Rockwell Automation (@rokautomation) • Instagram photos and videos
• Select a Region | Rockwell Automation

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>