MEGA LITE Nova-Lite Uv200 Party Light User Manual

MEGA LITE Nova-Lite Uv200 Party Light

Check that the unit has not been damaged during transport

Read all cautions and warnings prior to operation of this equipment

Protection Against Fire

1. Maintain a minimum of 1 foot distance from any type of flame.
2. Replace fuse only with the specified type and rating.
3. Do Not install the unit to close to a heat source.
4. Make sure cable are properly secured
5. Maximum surface operating temperature 113º.

Protection Against Electrical Shock

1. Disconnect power before servicing.
2. For connection to main power supply proceed to page 5.
3. This unit must be earthed. (electronically grounded)
4. This unit is IP 20 rated (do not expose unit to rain or moisture )

Protection Against Mechanical Hazards

1. Use safety chain when hanging unit.
2. Use quality clamps or bolts when positioning unit
3. Do not open unit while it is on, risk of electrical shock.

Safety Standards

1. This Products Conforms to USA and Canada ETL Safety Standards. And has been tested for Stage Lighting Safety Standards UL 1573

Technical Information

Part Numbers
4455– Nova Lite UV200

Mechanical Specifications

• DMX Connectors: Neutrik 3 & 5 pin
• Power connection: Neutrik Power Con to Nema 5-15 (cable mounted)
• Thermal: Maximum ambient temperature 105° Maximum surface temperature 113°
• Fastening System: Dual Yoke
• Display: Digital

Size: 10” x 7.25” x 17”

Weight: 7lb

| Size: 20” x 12” x 11”

Weight: 13lb

Electrical Specifications

• LED Quantity: 1 COB LED Ultra Violet
• LED Watts: 200W
• Nanometre : 390nm
• LED Lifetime: 40 to 80 thousand hours average
• Refresh Rate: 12000 Hz
• Power Input Voltage: 110V-240 50/60 Hz
• Ballast: Electronic auto switching
• Power Consumption: Watts: 196 Amps: 1.69

Control & Programming

• Protocol: DMX 512
• DMX Modes:
  • Mode 1 Channels Dimmer
  • Mode 2 Channels Dimmer, Strobe
  • Mode 3 Channels Dimmer, Strobe, Dim Speed
• Control Options: Display preset setting

Main Power Connection

Caution!

1. Do not connect fixture to a dimmer system.
2. This unit has Auto switching power supply. It will respond to 110V or 240V automatically
3. This unit must be earthed. (electronically grounded)

The occupation of the connection-cable is as follows:
This fixture is equipped with an electronic power supply that will let the unit operate from 100V to 240V from 50Hz to 60Hz

DMX-512 Connection

The fixture is equipped with Neutrik panel mount 3 and 5 pin XLR Sockets for DMX input and output. The sockets are wired in parallel. Only use a shielded twisted pair cable designed for RS-485 and 3 or 5 pin XLR plugs and connectors in order to connect the controller with the fixture or the fixture with another.

Caution!
At the last fixture the DMX signal needs to be terminated with a terminator. Solder a 120 Ohm re-sistor between the (-) and the (+) signal into a 3 pin XLR plug and plug it in to the last fixture on the signal run. Pre-manufactured terminator plugs are available for
purchase from your Mega-Lite dealer (P-DMX-T).

Display Menu

Nova Lite UV 200 DMX Profile

Nova Lite UV200 1Ch

Nova Lite UV200 2Ch

Nova Lite UV200 3Ch

3

|  | Dim Speed 0| 0-62
Dimming| Dim Speed 1| 63-124
Speed| Dim Speed 2| 125-187
 | Dim Speed 4| 188-255

Rigging the fixture

Pendant Mount: (Included)
When using pendant and treaded mount consider the following

1. Remove the yoke as it will no longer be used.
2. Using a standard 1/2 bolt you can hang the fixture by thread-ing directly into the top. ( a metric 10mm version is also available part #4450-HPM)
3. Using a steel cable you can hang the fixture by running a steel cable throw the side hole
4. It is very important that you secure the fixture with a second-ary safety .

Caution!

1. The installations must be carried out by an authorized dealer or trained professional.
2. Unit may cause severe injures if you have doubts concerning the safety do not install.
3. Unit is to be 24inches away from flammable materials (decoration material)
4. Use high quality installation equipment to hang unit.
   • When rigging a unit it is very important that you follow common safety procedures. Rigging requires extensive experi-ence including but not limited to calculating working loads, material being used and periodic safety inspections. If you lack these qualifications, do not attempt the installation yourself, instead use a professional structural rigger.
   • When rigging the unit always be secured with a secondary safety attachment. The installation location of the fixture has got to be built in the way that it can hold 10 times the weight for 1 hour with out any harming. Installation should be checked at least one time a year by a skilled person.

Cleaning and Maintenance

Installation Maintenance: The operator has to make sure that the unit is operating safely and has the installa-tions and electronics checked by an expert every year.

The following points have to be considered during the inspection:

1. All screws used for installing the device or part of the device have to be tightly connected and must not be corroded.
2. There must not be any deformations on the housing, fixation and installation spots (ceiling, suspension, trussing).
3. The electronic power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments. Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed.
   Note: There is no serviceable parts inside the device. Maintenance and service operations are to be carried out by authorized dealers.
   Replacing the fuse: Only replace the fuse with the same type and rating.
   Replacing the power cable: If the power cable of this device becomes damaged, it has to be replaced by author-ized dealers or trained professional only.
   Should you have further questions , please contact your dealer.

Parts List

Accessories

Warranty Information

Warranty Conditions

• Unless otherwise stated in writing, your product is covered by a one year parts and labor limited warranty.

• LEDs are not guaranteed to match in color temperature or output.

• It is the owner’s responsibility to furnish receipts or invoices for verification of purchase, date, and reseller or distributor. If purchase date cannot be provided, date of manufacture will be used to determine warranty period.

• Goods returned under warranty must follow the proper authorization procedure and must be accompanied by a copy of the original invoice and Return Authorization Number given by MSI.

• Goods repaired under warranty will be returned to the owner with the freight prepaid by MSI via the most economical means of shipment.

• Repair or replacement as provided for under this warranty is the exclusive remedy of the consumer. MEGA SYSTEMS INC. makes no warranties, express or implied, with respect to any product, and Mega Systems specifically disclaims any warranty of merchantability or fitness for a particular purpose. Mega Systems shall not be liable for any indirect, inci-dental or consequential damage, including lost profit, sustained or incurred in connection with any product or caused by product defect or the partial or total failure of any product regardless of the form of action, weather in contract, tort
  (including negligence), strict liability or otherwise, and weather or not such damage was foreseen or unforeseen.

• Warranty is void if the product is misused, damaged, modified in any way, or for unauthorized repairs or parts. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Mega-Lite
18668 Highway 16N
Helotes, TX 78023
Ph 210-684-2600 Fax 210-855-6279 www.mega- lite.com / info@mega-lite.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>