SEURA TW-5 Outdoor Tilting Wall Mount TV Installation Guide

SEURA TW-5 Outdoor Tilting Wall Mount TV

Compatible with Séura Outdoor TVs
Pair with any Séura Outdoor TV 42″ – 86″ or any other compatible display not surpassing a maximum weight limit of 220 lbs. Compatible with VESA mount patterns up to 600×400.

Safety

• Prior to the installation of this product, read all instructions. Keep this manual for future reference.
• This product is designed to mount televisions and any accessories weighing up to 220 lbs. to a vertical firm wall.

CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR.

Warnings

• Safety measures must be practiced at all times during the assembly of this product. Use proper safety equipment and tools for the assembly procedure to prevent personal injury.
• At least two qualified people should perform the assembly procedure. Proper installation must be followed as outlined in these installation instructions. Personal injury and/or property damage can result from dropping or mishandling the TV.
• Ensure that there are no missing or defective parts upon receipt. Never use defective parts.
• This product contains small parts that could be a choking hazard.
• The wall you affix the Séura mount to must be capable of supporting five times the weight of the television and the mount combined. A professional installer or structural engineer should inspect or verify the requirements of the wall.
• Do not use this product for any purpose other than to mount a VESA compliant TV on a vertical surface as outlined in this manual.
• This product should not be mounted on metal stud walls or cinder block walls.
• If drilling and/or cutting into the mounting surface, always make sure that the wall is clear of electrical wires. Cutting or drilling into an electrical line may cause serious personal injury.
• Make sure there are no water or natural gas lines inside the wall where the mount is to be located. Cutting or drilling into a water or gas line may cause severe property damage or personal injury.
• Do not install near sources of high heat.
• Do not install on a structure that is prone to vibration, movement or chance of impact.
  Note: The included hardware is for mounting on concrete, stone, brick, or wood studs . If you are uncertain about the nature of your wall, please consult your hardware or installation professional for proper mounting to types of walls.

Parts Included

Before using the device, please check the following contents of the box for completeness. Illustrations are not to scale. If any parts are missing or damaged, contact Séura.

Mounting Tools and Hardware

Parts and Tools Required (not included)
The following tools may be required depending on your particular installation. They are not included.

For Wood Stud Installation

• Stud Sensor (edge-to-edge stud finder is recommended)
• 7/32″ Drill Bit

For Concrete, Brick and Stone Installation

• 7/16″ Masonry Drill Bit
• Hammer
• Socket Wrench ½″ Socket
• ½″ Combination Wrench

Features

IMPORTANT: HANDLE THE TV IN A VERTICAL POSITION TO AVOID DAMAGE TO THE SCREEN. IF PLACING THE TV SCREEN-SIDE DOWN OR LEANING AGAINST A WALL DURING INSTALLATION, COVER THE SCREEN WITH A PROTECTIVE CLOTH OR BLANKET.

Installation

IMPORTANT: THIS PRODUCT MUST BE MOUNTED TO CONCRETE, STONE, BRICK OR WOOD STUDS. The wall must be able to support five times the weight of the television and the mount combined. A professional installer or structural engineer should inspect or verify the requirements of the wall.

Hang the Mounting Plate

Wood stud wall mounting:
See page 8 for mounting to concrete, stone or brick

1. Choose mounting location
   If mounting a Séura Outdoor TV, reference page 14 for measurements from the edges of the TV to the edges of the mounting template to properly place the template in the desired location on the wall. Note that it is NOT vertically centered on the TV screen.

2. Locate studs and mark the wall
   All hole locations must be centered on wood studs. Verify the center of the studs using an edge-to-edge stud finder. Level the template on the wall and mark four hole locations in the template slots (2 top and 2 bottom) with a pencil on the wall.
   For TV sizes 65″ and larger, mark and utilize six fasteners instead of four.

3. Drill pilot holes
   Pre-drill the four marked holes on the wall 3-inches deep with a 7/32″ drill bit.

4. Attach mounting plate
   Make sure the arrows on the mounting plate point up. Align the mounting plate with the pre-drilled holes. Attach mounting plate to wall using the four lag screws and four flat washers. Do not over tighten the lag screws. Tighten the lag screws only until the washers are pulled firmly against the mounting plate.

Concrete, stone or brick wall mounting:
See page 6 for mounting to a wood stud wall

1. Choose mounting location
   If mounting a Séura Outdoor TV, reference page 14 for measurements from the edges of the TV to the edges of the mounting template to properly place the template in the desired location on the wall. Note that it is NOT vertically centered on the TV screen.

2. Mark the wall
   Level the template on the wall and mark four hole locations in the template slots (2 top and 2 bottom) with a pencil on the wall. For TV sizes 65″ and larger, mark and utilize six fasteners instead of four.

3. Drill pilot holes
   Pre-drill the four marked holes on the wall 3-inches deep with a 7/16″ masonry drill bit. Insert a plastic anchor into each of these holes. If necessary, lightly tap each anchor into place with a hammer.

4. Attach mounting plate
   Make sure the arrows on the mounting plate point up. Align the mounting plate with the pre-drilled holes. Attach mounting plate to wall using the four lag screws and four flat washers. Tighten all lag screws using a socket wrench and ½″ socket. Make sure the anchor is seated completely flush with the concrete surface even if there is another layer of material, such as drywall. Do not over tighten the lag screws. Tighten the lag screws only until the washers are pulled firmly against the mounting plate.

Attach Tilt Mount TV Brackets to TV

IMPORTANT: Check your TV manual before attaching mount brackets to TV. Some models require attaching soundbar brackets in tandem with attaching mount brackets

Using a Philips #2 Screwdriver (or 6 mm Allen Wrench for 86” Ultra Bright TV), remove the four VESA mount screws from the back of the TV. Place the two identical Tilt Mount TV Brackets flat against the back of the TV with the arrows pointed towards the top of the TV. Line the brackets up with the VESA mount fastener locations. If mounting a Séura Outdoor TV, reference page 14 for the bracket hole that should be used on each Tilt Mount TV Bracket. Attach the Tilt Mount TV Brackets to the TV using the same four VESA mount screws that you just removed.

Note: If installing with a soundbar or if the TV’s VESA screws are not long enough to attach the Tilt Mount TV Brackets, then use the four included Security Torx T27 x 1.0 x 16mm Screws or the four included M6 or M8 Philips VESA screws that are slightly longer than the TV’s factory screws.

| Shade Series
---|---
TV| 55″| 65″| 75″
Screw Size| M6| M6| M8
| Full Sun Series
---|---
TV| 50″| 65″| 85″
Screw Size| M8| M8| M8

Note: Security Torx Screws (available with some mount models) provide additional security to attach the brackets to the TV. Installers may opt to use these in place of the TV’s VESA screws, even if longer screws are not needed to accommodate a soundbar bracket or mount brackets.

Hang the TV

IMPORTANT: NEVER TRY TO HANG A TV BY YOURSELF. ALWAYS USE AT LEAST TWO PEOPLE TO LIFT THE TV INTO PLACE.

1. Lift the TV nd bring the back of the TV towards the wall, positioning it slightly above
2.  Lower the TV to hook the bottom hooks of  the Tilt Mount TV Brackets on the lower rail  of the mounting plate.
3.  Bring the top of the TV closer to the wall  to hook the top hooks of the Tilt Mount TV Brackets on the top rail of the mounting plate.
4. Make sure the bottom and top rails are fully engaged.

Do not le that the top and bottom hooks of both mounting brackets are securely engaged on the upper and lower mounting rails of the mounting plate.

Adjust the TV

Caution: It is possible to dislodge your TV while you level it. Use extreme caution until you tighten the leveling and locking screws.

Séura recommends checking knobs, screws, and bolts every two to six months. Temperature fluctuations, wind, and normal wear and tear can loosen hardware over time.

Top leveling screw adjustment:
If your TV is not level, the two (2) top leveling screws located on the top of the tilt mount TV brackets will allow you to compensate for this tilt by adjusting the screws with the provided T27 Security Torx Screwdriver or 4mm Allen wrench.

1. Loosen both leveling screws (one on each bracket).
2. Adjust the tilt of your TV.
3. Tighten both leveling screws.
4. Do not overtighten the leveling screws.

Bottom locking screw adjustment:
After you have adjusted leveling the TV, tighten the two (2) bottom locking screws located on the bottom of the tilt mount TV brackets (one on each bracket) using the provided T27 Security Torx Screwdriver or 4mm Allen wrench.Do not overtighten the locking screws.

Tilt adjustment

Adjusting the TV Tilt Angle

1. Place one hand on the center-top edge of the TV.
2. Place the other hand on the center- bottom edge of the TV.
3. Using the upper hand, gently pull the top of the TV towards you while the lower hand gently pushes the bottom of the TV  away from you.

Adjusting the TV to the Original Position

1. Place one hand on the center-top edge of the TV.
2. Place the other hand on the center- bottom edge of the TV.
3. Using the upper hand, gently push the top of the TV towards the wall while the lower hand gently pulls the bottom of the TV  away from the wall.

After tilt is adjusted to the desired position, tighten the (2) tilt locking bolts on each bracket until the brackets are firmly secured. Do not overtighten the tilt locking bolts.

Séura Outdoor TV Mounting Measurement Guide
If mounting a Séura Outdoor TV model listed in the table below, use the corresponding measurements to locate the mounting plate template in the desired location on the wall as described in Step 1. In addition, use the bracket hole listed to determine which holes on the Tilt Mount TV Brackets to line up with the VESA holes on the TV as described in Step 2.

Séura Outdoor TV

Model

| Distance From Edges of TV to Edges of Mounting Template (use to place template on back of TV in Step 1)|

Top Tilt Mount TV Bracket Hole (line up with VESA hole on back of TV in Step 2)

---|---|---

Top of TV to Top of Mounting Template

| Bottom of TV to Bottom of Mounting

Template

| Left Edge of TV to Left Edge of Mounting

Template

| Right Edge of TV to Right Edge of Mounting

Template

UB4-50| 7 13/16 in| 6 15/16 in| 9 7/16 in| 9 7/16 in| Second hole down from top
UB4-65| 11 1/2 in| 10 5/8 in| 15 15/16 in| 15 15/16 in| Second hole down from top
UB4-85| 16 1/2 in| 15 5/8 in| 24 3/4 in| 24 3/4 in| Second hole down from top
SHD2-43 with Soundbar| 5 9/16 in| 9 9/16 in| 5 13/16 in| 5 13/16 in| Top hole
SHD2-55 with Soundbar| 6 in| 15 1/16 in| 11 1/8 in| 11 1/8 in| Second hole down from top
SHD2-65 with Soundbar| 6 3/16 in| 19 3/4 in| 20 9/16 in| 20 9/16 in| Second hole down from top
SHD2-75 with Soundbar| 8 7/8 in| 21 7/8 in| 19 3/4 in| 19 3/4 in| Second hole down from top
STM3-49U| 7 3/4 in| 6 7/8 in| 9 3/16 in| 9 3/16 in| Second hole down from top
STM3-55U| 9 1/4 in| 8 3/8 in| 11 7/8 in| 11 7/8 in| Second hole down from top
STM3-65U| 11 11/16 in| 10 13/16 in| 16 3/16 in| 16 3/16 in| Second hole down from top
STM3-86U| 16 7/8 in| 16 in| 25 3/8 in| 25 3/8 in| Second hole down from top
SHD1-55 with Soundbar| 8 7/8 in| 12 5/8 in| 11 5/16 in| 11 5/16 in| Second hole down from top
SHD1-65 with Soundbar| 9 15/16 in| 16 5/8 in| 15 11/16 in| 15 11/16 in| Second hole down from top
SHD1-75 with Soundbar| 21 1/8 in| 10 5/8 in| 20 1/4 in| 20 1/4 in| Second hole down from top

Example Wall Location
Shown for SHD2-55 with Soundbar

Specifications

GENERAL|

DISPLAY COMPATIBILITY

|

42″ – 86″ Séura Outdoor TVs

---|---|---
VESA COMPATIBILITY| Compatible with VESA mount patterns up to 600×400
MOUNTING PLATE DIMENSIONS| 26.25″ w x 11.4″ h
TILT| +0° / – 7° to – 10°
FINISH COLOR| Black Powder Coat
DURABILITY| Acrylic E-Coated Steel
INSTALLATION| MAXIMUM WEIGHT LIMIT| 220 lbs
INSTALLATION SURFACE| Solid / Brick / Stone / Masonry / Stud Wall
HARDWARE| Stainless Steel
SHIPPING| SHIPPING CONTAINER DIMS|

27.75″ w x 12″ l x 2.5″ h

SHIPPING WEIGHT| 14 lbs
PRODUCT WEIGHT| 12 lbs

Maximum Weight Limit: 220 lbs.
The wall structure must be capable of supporting at least five times the weight of the television and the mount combined. If not, the wall structure must be reinforced.

LIMITED PRODUCT WARRANTY

For information regarding Séura’s warranty policy, please visit our website: www.seura.com/warranty. If the current Séura warranty policy is after your product purchase date, please contact Séura Customer Support to request warranty documentation from the date of your purchase.
For additional customer support, please contact Séura.
Toll Free: 1-800-957-3872 (Monday – Friday 8:00 am – 4:30 pm, Central Time)
Website: www.seura.com/support

1230 Ontario Road Green Bay, Wisconsin 54311 1-800-957-3872
contacts@seura.com
www.seura.com

Publish date: December 5, 2022 Information is subject to change without notice.

References

• Consumer Product Registration - Séura
• p65warnings.ca.gov
• Premier Mounts
• Séura | Technology + Design
• Support - Séura

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>