StarTech SV231HU34K6, SV231DHU34K6 2 Port USB 3.0 KVM Switch User Manual

StarTech SV231HU34K6, SV231DHU34K6 2 Port USB 3.0 KVM Switch

For the most up-to-date information, please visit: www.startech.com

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by StarTech.com could void the user’s authority to operate the equipment.

Industry Canada Statement
CAN ICES-3 (A)/NMB-3(A) This device complies with Industry Canada licence- exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.

Introduction

Packaging Contents

• KVM Switch x 1
• Universal Power Adapter (NA/JP, EU, UK, ANZ) x 1
• Rubber Feet x 4
• Quick-Start Guide x 1

Product Overview

Front View (SV231HU34K6)

Rear View

Front View (SV231DHU34K6)

Rear View

LED Indicators

Auto EDID

3x Fast Flashes = Default Setting

• PC Selection Indicators
  • Green = PC Connected
  • Red = Port selected
• EDID LED Indicator
  • 2x Fast Flashes = EDID Copy mode
  • 3x Slow Flashes = Auto EDID
  • 3x Fast Flashes = Default Setting

Installation

Attach The Rubber Feet
To affix the Rubber Feet to the bottom of the KVM switch, peel off the backing on each of the four Rubber Feet and adhear them to the bottom of the KVM Switch, in the indicated areas.

Connect the Console

1. Power off the HDMI Display and any Peripherals before connecting to the KVM Switch.
2. Connect 1 (SV231HU34K6) or 2 (SV231DHU34K6) HDMI Display(s) to the Console HDMI Output Port(s), located on the rear of the KVM Switch.
3. Connect a USB Keyboard and a USB Mouse to the Console USB HID Ports, located on the rear of the KVM Switch.
4. (Optional) Connect an additional USB HID Device to the remaining Console USB HID Port, located on the front of the KVM Switch.
5. (Optional) Connect the Audio Device to the Console Audio Port, located on the rear of the KVM Switch.
6. (Optional) Connect up to two SuperSpeed USB 5Gbps (USB 3.2 Gen 1) Peripheral Devices to the Console USB Hub Ports, located on the front and rear of the KVM Switch.

Connect the PCs

1. Power off the Computer and any Peripherals before connecting to the KVM Switch.
2. Connect 1 (SV231HU34K6) or 2 (SV231DHU34K6) HDMI Cable(s) from the HDMI Port(s) on the Computer to the PC 1 HDMI Input Port(s) on the rear of the KVM Switch.
3. Connect a SuperSpeed USB 5Gbps (USB 3.2 Gen 1) Cable (Type-A Male to Type-B Male) from the USB-A Port on the Computer to the PC 1 USB Port on the rear of the KVM Switch.

Note: A SuperSpeed USB 5Gbps (or better) Cable is recommended for optimal performance.

1. (Optional) Connect a 3.5 mm Audio Cable from the Audio Port on the Computer to the corresponding PC 1 Audio Port on the rear of the KVM Switch.
2. Repeat Steps 1 to 4 for PC 2.

Operation

HDCP Switch

Note: If the HDCP version needs to be changed after the initial installation, a power cycle of the KVM and connected devices may be required. The HDCP Switch, located on the rear of the KVM Switch, is used to set the HDCP version the KVM Switch will use with connected devices. The HDCP Switch can select one of three different modes:

Auto – This mode makes the KVM Switch detect the highest compatible HDCP version between Source and Display, and will then use that mode. This mode is recommended for most setups.

This mode forces HDCP 1.4 between the connected Source and Display Devices, which may limit video performance. This mode should be used if you experience issues getting video to pass through the KVM Switch, as it can help with older device compatibility.

None – This mode disables the HDCP handshake between the connected devices and the KVM Switch, which means protected content will not passthrough the KVM Switch.

Power-On Sequence

1. Connect the Universal Power Adapter from a Wall Outlet to the Power Input Port on the rear of the KVM Switch.
2. Power on all Peripherals.
3. Select PC 1 and power on the corresponding Computer.

Note: Ensure that the Computer connected to the PC 1 ports has fully booted to the operating system before proceeding.

• Repeat Step 3 for PC 2.

EDID Button

The EDID Button, located on the rear of the KVM Switch, is used to set how the KVM Switch will handle EDID information. There are three different modes available:

• EDID Copy – This mode holds the EDID information of the current display and will always use that EDID information, even if another Display is connected instead. This can help if experiencing compatibility issues with the Display intended for the setup.
• EDID Auto – This mode causes the KVM Switch to read, store, and forward the EDID to the Source Device ports. This ensures switching between ports does not require re-transmission of the EDID to detect capabilities.
• Default EDID – This mode will set the KVM Switch to default to an EDID of 1080p. This means monitors with a higher resolution may not see those resolutions available.

Select A Port
To select a port, press the Port Selection Button, located on the front of the KVM Switch, until the desired Computer has been selected.

Note: When you switch between ports, it takes some time for the video signal to be communicated. After you select a port, wait three to four seconds before you select a different port.

Hot Keys Commands

To view detailed instructions on the use of Hot Key Commands, please visit:

• www.StarTech.com/SV231HU34K6
• www.StarTech.com/SV231DHU34K6

Technical Support

StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads

Warranty Information

This product is backed by a two year warranty. In addition, StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned for repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from misuse, abuse, alteration, or normal wear and tear.

Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.

Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise.

StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to the products you need in no time. Visit www.StarTech.com for complete information on all StarTech.com products and to access exclusive resources and time-saving tools. StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology parts. StarTech.com was founded in 1985 and has operations in the United States, Canada, the United Kingdom and Taiwan servicing a worldwide market.

Reviews
Share your experiences using StarTech.com products, including product applications and setup, what you love about the products, and areas for improvement.

StarTech.com Ltd. 45 Artisans Crescent London, Ontario N5V 5E9 Canad

• fr.startech.com

References

• StarTech.com | IT Pro's Trusted Source for Connectivity Accessories | Europe
• Drivers & Downloads | StarTech.com Support
• 2 Port Dual Monitor HDMI KVM Switch 4K60 - KVM Switches | Server Management | StarTech.com
• 2 Port HDMI KVM Switch 4K 60Hz w/USB Hub - KVM Switches | Server Management | StarTech.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>