Breville CBL920 Super Q Pro Blender Instruction Manual

: June 9, 2024
: Breville

Breville CBL920 Super Q Pro Blender

BREVILLE |COMMERCIAL RECOMMENDS

SAFETY FIRST

At Breville | Commercial we are very safety conscious. We design and manufacture consumer products with the safety of you, our valued customer, foremost in mind. In addition we ask that you exercise a degree of care when using any electrical appliance and adhere to the following.

IMPORTANT SAFEGUARDS

READ ALL INSTRUCTIONS BEFORE USE AND SAVE FOR FUTURE REFENCE

Remove and discard all packaging materials and stickers before ﬁrst use.
To avoid choking hazard for young children, remove and safely dispose the protective cover ﬁtted on the power plug.
Do not use it in moving vehicles or boats, do not use it outdoors, and do not use it for anything other than its intended use. Misuse can cause injury.
Close supervision is necessary when any appliance is used by or near children.
This appliance can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved.
Do not use the appliance near the edge of a countertop or table. Ensure the surface is level, clean and free of water and other substances. Please be aware that vibration during use may cause the appliance to move.
Do not use the appliance on (or close to) a hot gas or electric burner, or where it could touch a heated oven or surface.
Do not allow the cord to hang over the edge of a countertop, or to become knotted.
To avoid electric shock, do not immerse the cord, plug or motor base in water (or other liquids).
This appliance is equipped with a power cord having a grounding wire with a grounding plug. The appliance must be grounded using a 3-hole properly grounded outlet. In the event of an electrical short circuit, grounding reduces the risk of electrical shock.
If the power outlet is a standard 2-prong wall outlet, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet. Do not, under any circumstances, cut or remove the third (ground) prong from the power cord or use an adapter.
In order to avoid the possible hazard of the blender starting by itself due to inadvertent resetting of the overload protector on the motor, do not attach an external switching device (such as a timer) or connect the blender to a circuit that can regularly switch the blender on and off.
Do not operate appliance with a damaged cord or plug, or after appliance malfunctions, or if dropped or damaged in any way. Immediately cease use of the appliance and visit www.BrevilleCommercial.com or call Breville |Commercial Consumer Support for examination, repair or adjustment.

SAFEGUARDS FOR YOUR BLENDER

Wash the blender jug with warm soapy water before ﬁrst use.
Use only the blender jug and lid that is supplied with this blender. The use of attachments, including canning jars or accessories not manufactured or speciﬁed by Breville |Commercial may cause the risk of ﬁre, electrical shock, or injury.
Always ensure the blender is assembled properly before using. Lid must be ﬁrmly secured to the jug before operation to ensure internal contents do not escape, spray or overﬂow.
Always ensure the appliance is properly assembled as per instruction before use. Using the appliance without being properly assembled may cause product malfunction, product damage or pose safety risk including personal injury.
If the motor is straining under a heavy load, do not operate continuously for more than 10 seconds. Allow the motor to rest for 1 minute between uses on heavy loads. Note that none of the recipes in these instructions are considered a heavy load.
Do not leave the blender unattended when in use.
Flashing light indicates ready to operate. Avoid any contact with blades or moving parts.
Keep hands, ﬁngers, hair and clothing away from the blender during use. Always turn blender off and unplug at the wall before reaching inside.
Be careful when handling the blender jug as the blades are very sharp. Be careful when emptying the jug and during cleaning. Mishandling of the blades may cause injury.
Do not remove the jug from the motor base while blender is in use.
The blender is intended for food or drinks preparation. Do not use for anything other than food or drinks. Do not operate without any ingredients in the blender jug.
Never attempt to operate with damaged blades, or with utensils, or any foreign objects inside the blender jug.
To reduce the risk of severe injury to persons or damage to the blender, keep hands and utensils out of the jug while blending. The scraper and tamper provided can be used, provided the main lid is in place.
Never blend boiling hot liquids. Allow temperature to drop before putting into the jug for blending.
Be careful if hot liquid is poured into the blender, as it can be ejected out of the jug due to sudden steaming.
When blending hot liquids ensure inner measuring cap is in place. Cap will protect from splashing of hot liquids during blending and includes vents designed to relieve pressure and avoid steam build up.
When blending hot liquids, do not exceed the hot liquids maximum of 40oz. (1.2L).
Be careful removing the lid after blending hot liquids, as steam traps can form in the liquid and be ejected out of the jug.
Strictly observe the reduced capacity
limit for blending hot ingredients. Failing to follow this instruction may cause personal injury by hot liquid burn.
Never use attachments or accessories that are not supplied with this product or authorized by Breville |Commercial to be used on this product. Failing to follow this instruction may cause product malfunction, product damage or
even pose safety risk.
For optional accessories authorized by Breville |Commercial to be used on this product, please read all instructions supplied with the accessory in conjunction with the instructions contained in this booklet.
Do not put the blender jug in extremes of heat or cold, for example placing a cold jug into hot water, or vice versa.
Before moving the blender, cleaning or putting it away for storage, always turn blender off and unplug at the wall.

BREVILLE ASSIST™ PLUG

Your Breville | Commercial appliance comes with a unique Assist™ Plug, conveniently designed with a ﬁnger hole to ease removal from the power outlet.

SHORT CORD INSTRUCTIONS

Your Breville | Commercial appliance is ﬁtted with a short power supply cord to reduce personal injury or property damage resulting from pulling, tripping or becoming entangled with a longer cord. If an extension cord is used, (1) the marked electrical rating of the cord set or extension cord should be at least as great as the electrical rating of the appliance, (2) the cord should be arranged so that it will not drape over the countertop or table- top where it can be pulled on by children or tripped over unintentionally and (3) the extension cord must include a 3-prong grounding plug.

SAVE THESE INSTRUCTIONS

Components Rating Information
120 V ~60 Hz 1800 W

A. Inner measuring cup
Removable for quick addition of ingredients.
B. High performance lid
Withstands high velocity tasks, and is designed to vent steam and prevent splatter.
*C. 68 fl oz (2L) BPA-Free jug**
Impact resistant, shatter proof and dishwasher safe.
D. Extra-wide, heavy duty blade and bowl system
Designed with 4 powerful stainless steel blades contoured to the base of the jug for maximum cutting power and processing results including liquid-free processing.
E. Heavy duty metal coupling
For durable and long lasting performance under demanding conditions.
F. Heavy duty 1800W motor
High velocity power combined with high torque for outstanding results.
G. LCD indicator with timer
Counts down for pre-programmed settings, and counts up for speed dial settings.
H. Durable base
I. 5 preset programs
Optimize the blender’s capabilities for crushing ice, smoothies, stir, boost and A Bit More™.
J. Overload protection
Resettable thermal fuse for motor protection.
K. Manual speed control
Wide speed range from super slow stir up to high speed milling for precise control.

ACCESSORIES

L. Scraper
Designed to push food down from the walls, or for easily removing ingredients after blending. Always use scraper with the blender lid on (inner cap removed).
M. Tamper
Helps make frozen desserts, nut butters and dips by pushing thick foods directly into the blades. Always use tamper with the blender lid on (inner cap removed).
*N. 68 fl oz (2L) BPA-Free jug**
Impact resistant, shatter proof and dishwasher safe.

COPOLYESTER MATERIAL
This blender jug is made with copolyester, which is a tough, BPA – Free polymer used to make housewares products that can stand up to extreme use and repeated dishwasher cleaning. Products made from copolyester are impact resistant and shatter resistant and stay clear and durable even after hundreds of cycles in the dishwasher.

Breville | Commercial makes its BPA Free claim for this product based on independent laboratory testing performed for all the food contact plastic materials of the product per EU Commission Regulation No 10/2011. BPA Free Material is used in all parts that come into contact with food.

Functions

GETTING STARTED

Ready mode
Press ON | OFF button to power the unit to READY mode.

Sleep
After 2 minutes of inactivity, LCD powers off, and the ON | OFF button flashes red.
After 5 minutes of inactivity, the blender turns power OFF. Press the ON | OFF button to reactivate the blender.

VESSELS
This unit features two blending vessels. The Blender base automatically detects the vessel and adjusts blending times in pre-set programs to optimize food results.

68-ounce Jug
The jug is recommended for big volumes up to 68 ounces and can be used with all pre-set programs.

PAUSE / CANCEL

For Manual Blending:
First press pauses the selected speed. Second press cancels the selected speed. Turn the Dial to start blending again.

For Program Blending:
First press pauses selected program. Second press cancels the selected program. Press the program button to start the program again.

MANUAL OPERATION

Speed Control Dial
Turn the Speed Control Dial clockwise to select one of 12 speed settings from a slow STIR through to a very fast MILL.
To stop blending, turn the Speed Control Dial counterclockwise back to READY.
The blender is programmed to allow manual speeds to run for a total of 6 minutes (68-ounce Jug).

WARNING

Never blend boiling hot liquids.

Allow temperature of ingredients to cool down to room temperature before placing into blender jug.

PRESET PROGRAMS

PULSE | ICE CRUSH
A program of continuous pulsing designed to chop food into an even consistency or crush ice cubes.

SMOOTHIE
For dairy-based smoothies. A combination of speeds and pulses designed to combine and aerate ingredients into a smooth and creamy texture.

STIR
This program bypasses the intermittent start / stop feature of the low speed manual blending. It is designed for constant low speed blending when making emulsifications or working with low volumes of liquid.

BOOST
A one-touch program to reach maximum speed quickly and blend the contents to a fine consistency.
Use the tamper for best results.

A BIT MORE™
The A BIT MORE™ program is designed to produce a slightly finer texture across chunky mixtures and fine blends or to incorporate seasoning after tasting without over-blending.

TIMER
A precision speed control dial allows the user to set the perfect blending speed in conjunction with a built in 6-minute timer that will auto-stop the blend.

CLEAN
Use to remove most of the ingredients off the blender walls and blades. Add 4 cups of warm soapy water to the blender jug and press the CLEAN button. For harder to clean, sticky or thick ingredients, add ½ teaspoon of liquid dish detergent for extra cleaning power. For best results, clean the blender jug this way immediately after use.

NOTE
If the blender is running and you press a different preset button, it will switch to that program without stopping. If a program is running and you press the same program button again, it will pause that program and timer. To resume press the same program button again.

Tips

The inner measuring cap can be removed to add oils/liquids or other ingredients during blending. Extreme care must be taken as depending on the mixture volume and speeds of operation, splashes can eject from the lid. We do not recommend removing the inner measuring cap when blending hot liquid.
Do not exceed the maximum mark when adding foods and liquids into the blender.
Run the blender only for the appropriate amount of time required – do not over blend ingredients.
Use the PULSE | ICE CRUSH button when food is too thick or coarse to circulate within the blender jug.
The scraper and tamper accessories can be used during blending by removing the inner measuring cap. Always make sure the main lid stays firmly in place.
Ingredients may stick to the sides of the blender jug. To push food back onto the blades with the main lid on (inner cap removed), use the tamper provided to scrape down the sides of the jug, and continue blending.
If any moisture or liquid spills on top of the motor base during blending, turn the blender off and unplug from the outlet. Remove the blender jug, and wipe motor base immediately with a dry cloth or paper towel.
The optimum amount of ice cubes that the blender can process in the jug is 8 ounces (225g). That’s approximately 10 ice cubes.
When the blender has been running for 6 minutes in manual mode with the jug it will automatically turn off. This is a safety feature to protect the motor.
Thicker mixtures puree more efficiently if the jug is ¼ to ½ full.
Do not use metal utensils, as they may damage the blades or blender jug.
Dates and other dried fruits may vary in hardness and moisture content. If adding dried fruits to smoothies, use the tamper for the first 15–20 seconds of the SMOOTHIE setting.
To make nut milks, add 1–2 cups of raw or soaked/drained nuts. Add 3–4 cups of purified water, and process on MILL for 1 minute. Strain through a nut milk bag (or muslin/cheesecloth) over a large bowl or jug. Close bag and squeeze the pulp in the bag to extract as much milk as you can.
To soak or not to soak nuts? This is a personal preference and you can make nut milks with unsoaked or soaked almonds. Almonds are a great source of protein however they contain a naturally occurring compound that may prevent our enzymes from digesting the nuts effectively. Try soaking nuts overnight to help break down the compound. Always rinse and drain soaked nuts before use.
Roasting nuts to make nut butter allows their natural oils to be released during blending, and enriches the flavor. Some nuts, such as almonds and hazelnuts, have a lower oil content. Add rice bran, macadamia or coconut oil when blending, if needed.
Freshly milled whole grain flour does not keep as long as commercial flours.
This is because the inner layers of the grain contain rich oils, which can become rancid over time with exposure to heat and moisture. Always store your flour in an airtight container in a cool, dry place. Flour can be stored in the refrigerator or freezer in warm/humid climates.
Corn, soy beans and some other dried legumes and grains vary in their moisture content, and may not circulate properly during milling. Use the scraper or tamper during milling to assist with circulation.
To remove any food that cannot easily be scraped out from under the blades, replace lid and turn blender back on high speed for 4–5 seconds to spin foods out from under blades.

Blending Chart (Jug)

DRY MILLING
Please note that milling hard ingredients like spices, nuts, sugar, coffee, grains, etc. will cause scratching and clouding to the inside surfaces of the jug. This is a cosmetic result from milling these kinds of ingredients, and does not affect the performance of the jug.
Avoid over-processing spices though. Essential oils found in spices when combined with heat can damage the jug surface.

Breville-CBL920 Super-Q Pro-Blender-05

This blending chart should be used as a guide only.

Care & Cleaning

Vessels and lids
In order to keep your jug clean and avoid food drying on the blades, vessels and lids, follow the below steps as soon as possible after use:

Rinse most of the ingredients off the vessels and lids.

68-ounce jug

Add 4 cups (around 1L) of warm water and press the CLEAN button. If thick or sticky ingredients require extra cleaning power add a few drops of dish liquid detergent.
Rinse the jug and lid again and/or wash separately in warm soapy water with a soft cloth or bottle brush.

WARNING
Oils in citrus rind can damage the material of the jug if left to sit on the jug for too long. Always clean your blender jug immediately after processing citrus rind.

Sanitizing
The recommended sanitizing solution is 1½ tsp (7.5mL) of household bleach in 2 quarts (2L) of clean, cool water, mixed according to the recommended instructions on the bleach container.

To sanitize, follow the below steps:

After performing the auto clean cycle as per the instructions above, add half of the recommended sanitizing solution (1 quart/1L) to the jug. Secure the lid and inner lid and press CLEAN to run a sanitizing clean cycle.
Allow to stand for 1 minute, then empty solution.
To sanitize all the lids, scraper and tamper soak them in 1 quart (1L) of the sanitizing solution mixture for 2 minutes.
Place the empty jug and lid back on blender base and run on manual speed MIX for 10-20secs to remove any excess moisture from the blade area.
Do not rinse after sanitizing. Allow to air dry before storage. Rinse with clean water prior to next use.

Motor base
To clean the motor base, wipe with a soft, damp cloth then dry thoroughly. Wipe any excess food particles from the power cord.

Cleaning agents
Do not use abrasive scouring pads or cleaners on either the motor base or the jug, as they may scratch the surface. Use only warm soapy water with a soft cloth.

Dishwasher
The blender jug, tamper, scraper and all lids can be washed in the dishwasher on a standard wash cycle. Jug can be placed on the bottom shelf, and all lids should be washed on the top shelf only.

Stubborn food stains and odors
Strong smelling foods such as garlic, fish and some vegetables such as carrots may leave an odor or stain on the blender jug, and lids. To remove, soak blender jug and lids for 5 minutes in warm soapy water. Then wash with a mild detergent and warm water, rinse well and dry thoroughly. Store jug with the lid off.

Storage
Store your blender upright with the blender jug assembled on the motor base, or beside it. Do not place anything on top.

To allow air to circulate, keep the lid off.

Dry milling
Please note that milling hard ingredients like spices, nuts, sugar, coffee, grains, etc. will cause scratching and clouding to the inside surfaces of the jug.

This is a cosmetic result from milling these kinds of ingredients, and does not affect the performance of the jug.