espiro 2in1 Universal Pram User Manual

2in1 Universal Pram
User Manual

2in1 Universal Pram

|
---|---
|
|
|

ATTENTION! Correctly mounted shoulder straps

1. should be located slightly above the child’s shoulders, and the hip straps
2.  should tightly hold the child’s pelvis. Straps cannot be twisted

DEAR PARENTS
Congratulations on your purchase of YOGA stroller manufactured by the company BDG PROD UKCJA. Journey in this stroller will be safe, comfort and enjoyable. Impor t ant — Read carefully and keep for future reference Your child’s safety may be threatened if you do not follow these instructions!

1. ELEMENTS OF THE STROLLER
2. Seat
3. Canopy
4. Bumper bar
5. Footmuff
6. Frame
7. Rear wheel — 2 pcs
8. Front wheel – 2 pcs,
9. Basket
10. Carrycot
11. Cover na carrycot
12. Bag

UNFOLDING THE STROLLER

2. Unlock the snap fastener of the locking mechanism located on the outside of the frame (1) and pull the handle up (2).

3. unfold the stroller until the locking mechanism is secured in place.

4. Before use, check if both locks are properly secured in place.
   WHEELS

5. ASSEMBLY OF FRONT WHEELS Insert front set of the wheel onto the hub until it is locked in place. Make sure the wheel is properly secured. Repeat on the other side.

6. ASSEMBLY OF THE REAR WHEELS Insert the rear wheel onto the rear hub until it is locked in place. Make sure the wheel is properly secured. Repeat on the other side.

7. DISASSEMBLY OF THE FRONT WHEELS Press the button of the locking mechanism (1) and simultaneously take the wheel off the hub (2).

8. DISASSEMBLY OF THE REAR WHEELS Press the button of the locking mechanism (1) and simultaneously take the wheel off the hub (2).

9. FRONT SWIVELING WHEELS Move the locking mechanism down to lock front swiveling wheels. Move the locking mechanism up to unlock the front wheel.
   NOTE: Swiveling wheels must be unlocked prior to moving the stroller backwards!!! Failure to observe instructions for the swiveling wheels may result in mechanical damage to the steering elements, which are not subject to complaint.

10. PARKING DEVICE (brake) Press the brake pedal with the foot to lock the rear wheels. Lift the brake pedal with the foot to unlock the rear wheels.

11. ADJUSTING THE PARKING DEVICE
    NOTE: Carry out the adjustment using keys 8 and 10 (not provided in the set) To make the adjustments, proceed as follows:
    a) Unscrew the control nut (B) turning it to the right
    b) Turn the adjusting screw (A) to the left (1) to tighten the parking device
    c) Turn the adjusting screw (A) to the right (1) to loosen the parking device
    d) After adjusting the brake (adjusting screw (A) in appropriate location), tighten the control nut (B) to the adjusting screw to secure the screw against change of its location.

SEAT UNIT

ASSEMBLY AND DISASSEMBLY OF THE SEAT UNIT
NOTE: Never assemble or disassemble the seat unit with the child inside it.

12. Seat unit in the YOGA stroller can be assembled facing forward and backward. To do so, position the seat unit facing forward or backward and insert it into the mounting mechanism of the stroller locks.
    NOTE: Make sure the seat unit is properly assembled in the frame of the stroller.

13. To detach the seat unit from the stroller, press buttons on both sides of the seat unit and take it off the frame.

14. Remove the seat unit from the frame.

15. BACKREST ADJUSTMENT To change the position of the backrest, lift the adjusting handle (1) and adjust the backrest to desired position (2).

16. FOLDING THE SEAT UNIT Fold the canopy. Move the locking mechanism of the handle to the right (1) and lift the handle of the adjusting mechanism (2). Push the backrest to fold the seat unit (3).

17. UNFOLDING THE SEAT UNIT Move the locking mechanism of the handle to the right (1) and lift the handle of the adjusting mechanism (2). Lift the backrest to fold the seat unit.

BUMPER BAR

18. To assemble the bumper bar, insert it on plastic openings on both sides of the frame. Make sure the bumper bar is properly secured against sliding out.
19. To detach the bumper bar, press the buttons located below the bumper bar at the same time (1) and take it off the openings in the seat unit (2).

FOOTREST ADJUSTMENT

20. To lift the footrest, lift its end part.

21. To lower the footrest, pull the handle below the footrest (1) and lower it (2).
    CANOPY: ASSEMBLY AND OPERATION

22. Insert the ends of the canopy into the opening on the sides of the seat unit (1) and fix the canopy to the backrest with snap fasteners (2).

23. To detach the canopy, detach the snap fasteners, press locking mechanism on both sides of the seat unit (1) and take the canopy off the frame (2).

24. To change the position of the canopy, hold its top part and adjust it to the required position.

25. To additionally enlarge the canopy, unzip the zipper in the back part (1) and unfold the canopy (2).

26. To have access to the ventilation system of the canopy, enlarge it, unzip the zipper in the back part (1) and move the fabric (2).

27. SAFETY BELTS Lock belts with the buckle (1). Adjust the length of the straps with buckles (2).

28. ASSEMBLY / ADJUSTMENT OF THE SAFETY BELTS HEIGHT To assemble / To adjust the height of the seat belts, take them out of the openings in the backrest/seat unit and the upholstery and insert through openings in the upholstery and the seat unit/backrest at the desired height. NOTE! Before locking the child with the seat belts, make sure that the seat belts are properly assembled.

29. To use an additional harness, fix it on plastic rings located on the strollers belts.

30. FOOTMUFF Insert the footmuff on the footrest, place it below the bumper bar and fix with snap fasteners to the belts in the upholstery.

31. ASSEMBLY OF THE INSERT Thread the ends of the straps through the holes in the insert. Thread the straps through the buckles in the seat unit. Fix the straps using snap fasteners. After assembly, the insert should tightly adhere to the seat unit.

32. ASSEMBLY AND DISASSEMBLY OF THE RAIN COVER Mount the rain cover onto the seat unit so it protects the canopy and the footrest

33. GUIDE BAR LENGTH ADJUSTMENT Press the button on the guide bar (1) and at the same time adjust it to the required position (2).

34. FOLDING THE STROLLER Unlock the front wheels. Press the button of the locking mechanism (1) and turn the folding handle (2).

35. Fold the stroller until the locking mechanism of the stroller is secured in place.

36. CARRYING STRAP The stroller can be carried using the strap delivered with the set.
    NOTE: The strap is equipped with buckles used to disassemble the strap from the stroller.

37. FOLDING THE STROLLER WITH THE SEAT UNIT The stroller can be folded with the seat unit assembled facing both sides. Unlock the front wheels. Seat unit facing forward Fold the seat unit forward (1)

38. move the seat unit so that its backrest is located close to the rear wheels (2). Seat unit facing backward

39. Move the seat unit so that its backrest is located close to the rear wheels (1).

40. Fold the frame until the locking mechanism is secured in place.

41. After folding, the stroller can be left on the wheels or the guide bar.

CARRYCOT

UNFOLDING THE CARRYCOT

42. Unfold bars of the carrycot (1) until it is locked in plastic holders (2).
43. Fix the insert of the carrycot with a zipper (1) and next, plac
44. Insert the canopy onto the carrycot toy bar.
45. Zip the zipper below the carrycot toy bar.
46. Zip the zipper fixing the canopy to the carrycot.
47. Assemble the edges of the canopy to the toy bar using studs.
48. Slide the end of the bassinet bracket on the chassis bracket, until you hear a distinct click sound
49. To disassemble the carrycot, press the button below the carrycot
    (1) and at the same time take the carrycot of the frame
    (2). Disassemble the carrycot adapters from the stroller.

FOOTMUFF

50. Fix the footmuff with a zipper. RAIN COVER

51. Mount the rain cover onto the carrycot

52. ASSEMBLY AND DISASSEMBLY OF THE CARRYCOT
    NOTE: Adapters of the carrycot can only be used to assemble the carrycot on the stroller. To fix the adapters of the carrycot on the pram’s frame, insert them in the locking mechanism of the stroller (1). To disassemble the carrycot adapters, press the button (2) and take the adapter of the frame (3).
    NOTE: Never assemble or disassemble the carrycot unit with the child inside it. To assemble the carrycot, position it so that the canopy is in the front part of the frame and insert it in the previously assembled adapters of the carrycot.
    NOTE: Make sure the carrycot is properly assembled in the frame of the stroller.

53. To assemble the carrycot on the stroller, position it so that the canopy is in the front part of the frame and insert it in the previously assembled adapters of the carrycot.
    NOTE: Make sure the carrycot is properly assembled in the frame of the stroller.

54. Insert the end of the carrycot support onto the stroller support until you hear a clear click. To disassemble the carrycot, detach the support from the stroller frame.

55. To disassemble the carrycot, press the button below the carrycot
    (1) and at the same time take the carrycot of the frame
    (2). Disassemble the carrycot adapters from the stroller.
    Note: the carrycot may also be assembled directly on the frame of the stroller.

56. ASSEMBLY OF THE BAG ON THE STROLLER HANDLE Place the bad in the holder on the guide bar.

57. ASSEMBLY AND DISASSEMBLY OF THE CAR SEAT BABY SAFE YORK ON THE FRAME OF THE STROLLER
    NOTE: Never assemble or disassemble the car seat with the child inside it.
    ASSEMBLY OF THE CAR SEAT

58. Fix the adapters on the frame of the stroller inserting them in the openings of the stroller locks. Make sure they are properly locked in place.

59. Place the car seat facing backwards and insert it into previously assembled adapters
    (1). Press the buttons on both sides of the stroller handle
    (2) and fold them
    (3) to lock it in the adapters.
    NOTE: Make sure the car seat is properly assembled. DISASSEMBLY OF THE CAR SEAT

60. Press the buttons on both sides of the stroller handle
    (1) and lift the handle
    (2). Take the car seat off the adapters (3).

61. Disassemble each adapter by pressing the button
    (1) and taking the adapter off the frame
    (2). Repeat on the other side.

 CLEANING AND OPERATING

Plastic parts of the stroller and stripes may be cleaned with soft, damp cloth. Do not use aggressive cleaning agents.
Clean metal parts with dry cloth removing dust and water. If the stroller gets muddy or after its use during winter, maintain it with use of lubricating products.
Upholstery cleaning manual: – Clean using a cloth with mild cleaning agent, do not wet it, do not whirl, dry unfolded.
Check periodically if screws did not get loose and replace damage parts. Lubricate riding elements, i.e. wheels hubs and axes using common products, eg. silicone grease. It should be done especially after using the stroller on sandy ground or during winter. Aggressive agents may cause corrosion. Remember to maintain all metal elements.
WARNING
IMPORTANT— READ CAREFULLY AND KEEP FOR FUTURE REFERENCE

• WARNING Never leave the child unattended
• WARNING Ensure that all the locking devices are engaged before use
• WARNING To avoid injury ensure that your child is kept away when unfolding and folding this product
• WARNING Do not let the child play with this product
• WARNING This seat unit is not suitable for children under 6 months
• WARNING Always use the restraint system
• WARNING Check that the pram body or seat unit or car seat attachment devices are correctly engaged before use
• WARNING This product is not suitable for running or skating
• Maximum weight and age of the child for which the vehicle is suitable: 22 kg or 4 years whichever comes first.
• Parking device (brake) should be activated when putting the child in or taking the child out of the stroller
• When parking the stroller, always activate the brake (parking device)
• Maximum load of the bag on the stroller’s handle is 1.5 kg.
• Maxim load of the basket is 3 kg.
• Maximum load of pocket of the canopy/carrycot is 0.3 kg.
• Any load on the handle and/or posterior part of the backrest and/or sides of the stroller will influence stability of the stroller
• Do not hang bags which are not appropriate for hanging or bags different than recommended by the manufacturer on the stroller’s guides
• it is dangerous and may lead to damage to the stroller. – This stroller is intended for use by one child.
• Do not use accessories which are not approved by the manufacturer. Use only spare parts which are approved or recommended by the manufacturer.
• Do not use additional platforms attached to the stroller.
• In the event any defects are detected, do not use the product and contact the service of BDG PRODUKCJA of the seller.
• Never go down or up the stairs with the stroller (also on slides), especially with a child inside
• it may lead to serious injury to the child and damage to the stroller. – Rocking the stroller may deteriorate its structure and lead to damage.
• Never lift or move the product with the child inside it.
• Make sure folding elements are locked prior to using the stroller (that is is properly unfolded and locked in place).
• Always assemble all protective and securing elements of the stroller in compliance with instructions.
• Always attach the crotch belt on the bumper bar.
• Check periodically if all elements of the stroller are operational and safe, in particular check if the seat unit, carrycot and the car seat are properly assembled to the chassis.
• When folding and unfolding the stroller, as well as when adjusting the backrest, handle or other elements of the stroller, keep your and your child’s body parts safe.
• The stroller is intended for moving forward.
• Baby Design Group sp. Z o.o. sp. K. is not liable for any damage to property or injuries arising from the assembly and use of the product which is not compliant with instructions and recommendations of the manufacturer covered by this user manual.
• Use only elements supplied or recommended by the manufacturer/distributor.
• You may assemble the carrycot, seat unit, or the car seat on the stroller’s frame. Carrycot:
• Do not use any additional mattress than the one recommended by the manufacturer.
• The product shall not be used, as soon as the child is able to sit by himself, roll over and can push itself up on its hands and knees. Maximum weight of the child: 9kg.
• Handles for carrying should be placed outside the carrycot when using it. Car seat:
• Car seat does not substitute cradle or baby cot. If your child wants to sleep, put it inside and appropriate carrycot, cradle or baby cot. Upholstery cleaning manual:
• Clean using a cloth with mild cleaning agent, do not wet it, do not whirl, dry unfolded. Be aware of the risk of open fire and other sourced of strong heat in the vicinity of the product.
• Wheels: inflate to 28P.Sl. (2.0BAR).

Silica gel packets inside. Do not swallow. Discard after unwrapping the product.

BDG PRODUKCJA SR Z.O.O.
UI. Warszawska 8
42 — 262 Poczesna
POLAND
Tel. +48 (34) 360 46 64, +48 (34) 360 46 53
Tel. serwis +48 (34) 364 36 41
E- mail:biurogbabydesign.eu,
E- mail serwis:serwis@babydesign.eu

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>