SW-MOTECH BC.SYS.07.945.31000/B SLC Side Carrier Instruction Manual

ANBAUANLEITUNG
mounting instructions
BC.SYS.07.945.31000/B contains
HTA.07.945.10000
HTA.07.945.11000
SYS.00.005.10000L/B
SYS.00.005.10000R/B
BC.SYS.00.005.10000

MOUNTING INSTRUCTIONS
Art. / Item No.: HTA.07.945.1*000
Revision: 00 – Datum / Date: 04 – 2020

SLC side carrier

Thank you for choosing this premium product from SW-MOTECH.
Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and/or stability of your vehicle.

GENERAL INFORMATION

Observe the country-specific regulations concerning vehicle registration/operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturers’ specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.

PARTS LIST

Note:
a All measurements in millimeters.
b The second number indicates the total quantity of the part in the delivery.
c No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.

MOUNTING

NOTE: The following mounting steps show the mounting of the left side carrier.
Mount the right side carrier in the same way.
Attach the parts (2] to [5) to the side carrier (1), as shown in the schematic drawing.
ATTENTION: Use liquid thread locker!
Tighten the screws as specified.

Remove the original luggage rack from the vehicle.

Mounting w/o SW-MOTECH luggage rack
Attach the side carrier (1) to the vehicle, as shown in the drawing.
ATTENTION: Use liquid thread locker!
Tighten the screws with the manufacturers specified torque.

Mounting with SW-MOTECH luggage rack

NOTE: When mounting the side carrier with the SW-MOTECH luggage rack, the spacers (10) are not required. Mount instead the marked (*] parts of the luggage rack.
Attach the side carrier (1} to the vehicle, as shown in the drawing.
ATTENTION: Use liquid thread locker!
Once all parts are aligned without excess tension, tighten the screws as specified.

MOUNTING INSTRUCTIONS
READ AND SAVE THESE MOUNTING INSTRUCTIONS
Art.-Nr. / Item No.: SYS.00.005.10000+/B
Revision: 02 – Datum / Date: 06 – 2022

Adapter plate for SysBag WP M

Thank you for choosing this premium product from SW-MOTECH.
Please carefully read and understand all instructions, safety messages and warnings in this mounting instructions prior to installation and use of this
product to avoid injury.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop. Keep these mounting instructions as reference.
SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!

SAFETY ALERT SYMBOL

This safety alert symbol is used throughout these mounting instructions to warn of the possibility of death, bodily injury or other warnings. The words DANGER, WARNING and CAUTION are used with this safety alert symbol to convey important safety messages and information related to the installation and use of this product. These words along with the safety alert symbol mean:
DANGER: Indicates a hazardous situation that, if not avoided, will result in death or serious injury!
WARNING: Indicates a hazardous situation that, if not avoided, could result in death or serious injury!
CAUTION: Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury!
NOTICE: |mportant information, but not death or injury related (property damage only)!
WARNING: The installation and/or maintenance of this product requires advanced mechanical skills, the proper tools, and a thorough understanding of tool use and torque specifications. For your own safety, SW-MOTECH recommends having installation and/or maintenance carried out by a qualified and certified motorcycle mechanic.
WARNING: Should you choose to self-install this product, carefully and completely read all intallation and safety instructions before installation and use, and follow all the directions and safety precautions given in the mounting instructions to avoid serious injury or death. Also pay attention to all relevant information in the vehicle manual during intallation and use.
IF YOU DO NOT UNDERSTAND ANY PART OF THESE INSTRUCTIONS, OR NEED CLARIFICATION OF ANY INSTRUCTION, DO NOT ATTEMT TO MOUNT THIS PRODUCT WITHOUT CONTACTING SW- MOTECH FOR ASSISTANCE.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included.
CAUTION: Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the engine/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools and wear always safety glasses and hand protection. Have another person help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturer specifications or replaced by parts and hardware delivered by SW-MOTECH.
WARNING: Secure all threads, unless otherwise specified, with medium- strong strength liquid thread locker. Torque specifications undefined by SW- MOTECH must be obtained from the vehicle manufacturer or by a certified motorcycle workshop!
FUNCTION CHECK: After installation also make sure that no moving parts are obstructed, and function of the vehicle is not hindered in any way. Cables and hoses must not rub and/or be pinched.
WARNING: Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all connections and the proper fit of the product. Installed accessories can change driving behavior/stability of the vehicle.

PARTS LIST
READ AND SAVE THESE MOUNTING INSTRUCTIONS

Note:
a All measurements in millimeters.
b The second number indicates the total quantity of the part in the delivery.
c No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.

MOUNTING
READ AND SAVE THESE MOUNTING INSTRUCTIONS

WARNING: Always wear eye and hand protection!
WARNING: Always use appropriate tools!
NOTICE: The mounting steps [1] to [3] show the mounting of the left adapter plate. Mount the right adapter in the same way.
NOTICE: Select the installation positions A or B ,shown in the detail drawing, according to your installation situation.
Attach the quick release fastening system (2) to the adapter plate (1).
Tiahten the screws as specified.

First loosely loop the adapter plate with the vertical straps on the SysBag.
In doing so, push the middle lug of the adapter plate under the tab shown on the back of the bag.
Before looping through the D-rings, slide the rubber loops over the straps.

Guide the side straps through the slits in the adapter plate and then pull all straps tight. Make sure that the adapter plate is firmly seated.
Now loop all six straps onto the D-rings, as shown in the upper detail drawing.
Secure the excess lengths of the straps with the rubber loops, respectively the velcro straps, as shown in the lower detail drawing.

Place the locking openings of the quick release fastening system onto the guide bolts of the adapter kit for SysBag [sold separately).
Then press the SysBag onto the guide bolts, until it properly rests on your SW-MOTECH carrier system.

WARNING: Make sure that all guide bolts of the adapter kit for SysBag engage at the same time!
Pay attention to the clearly audible snap sound of the locking mechanism!
To release press the slider downward.

PRODUCT SPECIFIC INFORMATION

NOTICE: Observe the country-specific regulations concerning vehicle registration/operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.

Art.-Nr. / Item No.: see parts list
Revision: 00 – Datum / Date: 04 – 2022

SysBag WP S/M/L

Thank you for choosing this premium product from SW-MOTECH.
Please carefully read and understand all instructions, safety messages and warnings in this mounting instructions prior to installation and use of this
product to avoid injury.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop. Keep these mounting instructions as reference.
SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!

SAFETY ALERT SYMBOL

This safety alert symbol is used throughout these mounting instructions to warn of the possibility of death, bodily injury or other warnings. The words DANGER, WARNING and CAUTION are used with this safety alert symbol to convey important safety messages and information related to the installation and use of this product. These words along with the safety alert symbol mean:
DANGER: Indicates a hazardous situation that, if not avoided, will result in death or serious injury!
WARNING: Indicates a hazardous situation that, if not avoided, could result in death or serious injury!
CAUTION: Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury!
NOTICE: |mportant information, but not death or injury related (property damage only)!
WARNING: The installation and/or maintenance of this product requires advanced mechanical skills, the proper tools, and a thorough understanding of tool use and torque specifications. For your own safety, SW-MOTECH recommends having installation and/or maintenance carried out by a qualified and certified motorcycle mechanic.
WARNING: Should you choose to self-install this product, carefully and completely read all intallation and safety instructions before installation and use, and follow all the directions and safety precautions given in the mounting instructions to avoid serious injury or death. Also pay attention to all relevant information in the vehicle manual during intallation and use.
IF YOU DO NOT UNDERSTAND ANY PART OF THESE INSTRUCTIONS, OR NEED CLARIFICATION OF ANY INSTRUCTION, DO NOT ATTEMT TO MOUNT THIS PRODUCT WITHOUT CONTACTING SW- MOTECH FOR ASSISTANCE.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included.
CAUTION: Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the engine/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools and wear always safety glasses and hand protection. Have another person help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturer specifications or replaced by parts and hardware delivered by SW-MOTECH.
WARNING: Secure all threads, unless otherwise specified, with medium- strong strength liquid thread locker. Torque specifications undefined by SW- MOTECH must be obtained from the vehicle manufacturer or by a certified motorcycle workshop!
FUNCTION CHECK: After installation also make sure that no moving parts are obstructed, and function of the vehicle is not hindered in any way. Cables and hoses must not rub and/or be pinched.
WARNING: Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all connections and the proper fit of the product. Installed accessories can change driving behavior/stability of the vehicle.

PARTS LIST
READ AND SAVE THESE MOUNTING INSTRUCTIONS

Note:
a All measurements in millimeters.
b The second number indicates the total quantity of the part in the delivery.
c No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.

MOUNTING
READ AND SAVE THESE MOUNTING INSTRUCTIONS

FASTENING TO THE VEHICLE
WARNING: Always wear eye and hand protection!
WARNING: Always use appropriate tools!
WARNING: Protect sensitive surfaces in the area of the SysBag (1) and the fastening straps with the adhesive protection foil (2) from scratches!
Place your SysBag [1] in the rear area of your vehicle (e.g. passenger seat, luggage rack etc.].
Entangle the loop straps (3) to appropriate and reliable attachment points of the vehicle [e.g. vehicles frame, footrest mounts, luggage hooks etc.).
Attach the loop straps (3) on both sides to the D-rings of the SysBag (1).
Tighten all loop straps until the SysBag (1) is centered and securely fastened to the vehicle.
Secure the overlength of the loop straps (3) with the rubber loops.

FASTENING TO THE SW-MOTECH LUGGAGE RACK
NOTICE: Optionally, use the antislip hoses [4] on the straps of the SysBag [1] to attach the SysBag more firm to the luggage carrier!
Run the straps of the SysBag (1) through the shown openings of the lugagge rack. Attach them to the D-rings of the SysBag as shown in the detail drawing.
Tighten all straps until the SysBag is centered and securely fastened to the luggage rack.
Secure the overlength of the straps with the velcro fasteners of the SysBag.
NOTICE: Optionally, the side straps of the bag can be shortened. To do this, cut the strap behind one of the seam marks as shown in the detail drawing above.
Then fuse the cut edge with a lighter to avoid fraying.

FASTENING TO VARIOUS SIDE CARRIERS
WARNING: Use the antislip hoses (4) on the straps of the SysBag to attach the SysBag (1) more firm to the side carrier!
Loop the straps of the SysBag [1)on the side carrier. Then loop the straps onto the D-rings of the SysBag, as shown in the detail drawing.
Tighten all straps until the SysBag is centered and firmly attached to the side rail.
Secure the excess lengths of the straps to the SysBag with its Velcro straps.
NOTICE: Optionally, the side straps of the bag can be shortened. To do this, cut the strap behind one of the seam marks as shown in the detail drawing above. Then fuse the cut edge with a lighter to avoid fraying.

Roll the reinforced opening three times and close the buckle.
Then close the SysBag [1] with the buckle of the lid.

LOADING
WARNING: Never store pointy or sharp-edged objects, which could cause injury to persons or damage to the vehicle/side case!
WARNING: Make sure weight is evenly distributed between the left and right SysBag. Make sure that the loanding is secured against shifting during the ride!

WARNING: Surface materials can experience color changes or fading when exposed to direct sunlight for extended periods of time and by environmental factors (e.g., SMOG, acid rain, etc.)! SW-MOTECH assumes no liability for this.

CARE
For cleaning use ONLY a soft textile brush, cloth or sponge and warm soapy water! Rinse with clean water.
Do NOT use strong cleaning agents, rough cleaning tools or high pressure washer!
Clean the SysBag after riding in salty conditions, to avoid  Damage from salt.

COMBINATIONS

The SysBag line has only three bags but offers a vast variety of mounting options and combination possibilities. The bags can be lashed to the tail end or at the side, as described in the mounting instructions, or mounted to the carrier / rack with a quick-release fastener. On this page you will find some mounting examples.
Vehicle-specific solutions, SysBag sets and adapter plates for SW-MOTECH carriers / racks can be found in our webshop.

PRODUCT SPECIFIC INFORMATION

WARNING: Riding with this product may affect the motorcycles driving and braking performance!
WARNING: Depending on the location of fixation, cornering and ground clearance can be reduced by using this product!
WARNING: Before riding and at each stop (every 200 km) check proper fixation of the product!
NOTICE: Observe the country-specific regulations concerning vehicle registration/operation as wellas TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.

WARNING: The maximum vehicle load specified by the manufacturer and the maximum load of the SW-MOTECH carrier/rack must not be exceeded!

WARNING: SYSBAGS S/M ARE NOT SUITED FOR OFFROAD-USE!

SW-MOTECH GmbH & Co. KG
Ernteweg 7-10
35282 Rauschenberg Germany
Tel. /phone + 49 (0)6425 / 8168 – 050
Fax / fax + 49 (0)6425 / 8168 – 10
info@sw-motech.com
www.sw-motech.com
Copyright by
SW-MOTECH GmbH & Co. KG
Errors and omissions are expected. Technical and design modifications are subject to change.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>