Hamilton Beach 40715 Espresso Machine with Steamer User Manual
- June 9, 2024
- Hamilton Beach
Table of Contents
Hamilton Beach 40715 Espresso Machine with Steamer
For questions and other information:
USA – 1.800.851.8900
hamiltonbeach.com
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and/or injury to persons,including the following:
-
Read all instructions.
-
This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they are closely supervised and instructed concerning use of the appliance by a person responsible for their safety.
-
Close supervision is necessary when any appliance is used by or near children. Children should be supervised to ensure that they do not play with the appliance.
-
Do not touch hot surfaces. Use handles or knobs. Care must be taken, as burns can occur from touching hot parts or from spilled, hot liquid.
-
To protect against electric shock, do not place cord, plug or espresso maker in water or other liquid.
-
Unplug from outlet when the espresso maker is not in use and before cleaning. Unplug and allow to cool before putting on or taking off parts and before cleaning the appliance.
-
Appliance must be operated on a flat surface away from the edge of counter to prevent accidental tipping.
-
Do not operate any appliance with a damaged supply cord or plug, or after the appliance malfunctions or has been dropped or damaged in any manner. Supply cord replacement and repairs must be conducted by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard. Call the provided customer service number for information on examination, repair, or adjustment.
-
The use of accessory attachments not recommended by the appliance manufacturer may result in fire, electrical shock, or personal injury.
-
Do not use outdoors.
-
Do not let cord hang over edge of table or counter or touch hot surfaces, including stove.
-
Be certain filter holder is securely in place when brewing espresso.
Scalding may occur if the filter holder is removed during the brewing cycle. -
Do not place appliance on or near a hot gas or electric burner or in a heated oven.
-
Always plug cord into the wall outlet before turning on any controls.
To disconnect espresso maker, turn controls to OFF ( ) and then remove plug from wall outlet. To unplug, grasp the plug and pull from the outlet. Never pull from the power cord. -
WARNING! To reduce the risk of fire or electric shock, do not remove the bottom cover of the espresso maker. No userserviceable parts are inside. Repair should be done by authorized service personnel only.
-
Do not use appliance for other than intended use.
Other Consumer Safety Information
This product is intended for household use only.
WARNING Electrical Shock Hazard: This appliance has a polarized plug (one wide blade) that reduces the risk of electric shock. The plug fits only one way into a polarized outlet. Do not defeat the safety purpose of the plug by modifying the plug in any way or by using an adapter. If the plug does not fit, reverse the plug. If it still does not fit, have an electrician replace the outlet.
The length of the cord used on this appliance was selected to reduce the hazards of becoming tangled in or tripping over a longer cord. If a longer cord is necessary, an approved extension cord may be used. The electrical rating of the extension cord must be equal to or greater than the rating of the appliance. Care must be taken to arrange the extension cord so that it will not drape over the countertop or tabletop where it can be pulled on by children or accidentally tripped over.
Parts and Features
Before First Use
(Priming the Pump)
Wash all removable parts in warm,soapy water. No parts may be washed in a
dishwasher.
The water pump must be “primed” before first use to work properly.
Operating without water in the Water Reservoir can permanently damage the
appliance.
-
Make sure all three buttons are in the OFF position (not pushed in) and that the Steam Control Dial is turned fully clockwise to NO STEAM ( ).
-
Fill the Removable Water Reservoir to the MAX fill line with cold water and replace securely on the back of unit.
-
Plug into outlet. Press ON/OFF button to turn unit on.
-
When unit is ready, the light next to the Temperature Selection button will come on. Place an empty container under Frothing Nozzle so that nozzle is completely inside container.
-
Turn the Steam Control Dial counterclockwise to STEAM ( ).
Press Pump Button to pump hot water out of Frothing Nozzle for cleaning purposes. -
Fill the container about halfway full.
NOTE: The green light next to Temperature Selection button will go off once Pump Button is pushed. -
Press Pump Button again to turn Frothing Nozzle off; then turn Steam Control Dial clockwise to NO STEAM ( ).
-
Place a container under Brew Head; it should be wide enough to catch water from both spouts. Press Pump Button and dispense any remaining water from Removable Water Reservoir.
-
Press Pump Button again to turn off.
-
Press ON/OFF Button to turn the unit OFF. The light next to the button will go off. Unplug the unit.
-
Wash all parts again with warm,soapy water and dry thoroughly. See “Care and Cleaning” for full instructions.
How to Use
-
Make sure all three buttons are in the OFF position (not pushed in) and that the Steam Control Dial is turned fully clockwise to NO STEAM ( ).
-
Fill the Removable Water Reservoir with desired amount of cold water and replace securely on the back of unit.
-
Place Ground Espresso Holder into Filter Holder. Add one tablespoon (5 g) of ground espresso for each cup being made. Use shallow Holder for 1 cup (237 ml) and deep Holder for 2 cups (474 ml). Press grounds firmly into Holder with Tamping Tool.
-
Place pod into filter holder. When using single-serve pod, always use the shallower Espresso/Pod Filter Holder.
Never put two pods in either Filter Holder at one time.
-
Holding handle securely, align raised dimple on the exterior of Espresso/Pod Filter Holder with cutout notch on inside of Filter Holder. Rotate Espresso/Pod Filter Holder 180º to secure in base. Ensure no grounds are on rim of Filter Holder.
-
Rotate the Filter Holder to the right until it is firmly locked into place.
-
Plug into outlet. Press ON/OFF Button to turn unit ON. When ready, the light next to the Temperature Selection button will come on.
-
Place one or two cups under Brew Head spouts. If using one cup, use one wide enough to catch espresso from both spouts.
-
Press Pump Button to begin flow of espresso; press Pump Button again to stop flow. As espresso dispenses,it will gradually look lighter in color.
Allow espresso to drip from Filter Holder for 15-20 seconds before removing cup(s). -
Wait about 1 minute before removing Filter Holder from machine to allow espresso grounds and excess water still flowing through the pump to finish.
NOTE: Some water may continue to drip intermittently from Brew Head. This is normal and a result of product operation. -
To empty espresso grounds and/or an espresso pod from the Filter Holder, flip the plastic lever located on the handle of the Filter Holder and hold the lever open.
-
Keeping thumb on handle lever,dispose of espresso grounds and/or pod filter.
-
Ensure Filter Holder is cool. Align raised dimple on Espresso/Pod fFilter Holder with cutout notch in filter holder base; then remove.
-
Clean Filter Holder and Brew Head after each use. See “Care and Cleaning.” DO NOT allow grounds to remain in Filter Holder; this can clog Filter Holder and cause unit to malfunction.
How to Steam Milk
WARNING Burn Hazard. Vapor and water emitted from frothing nozzle are hot.
-
Ensure there is water in the Removable Water Reservoir and move the Frothing Nozzle to the right of the unit.
-
Plug into outlet. Press ON/OFF Button to begin heating water. When heated, the light next to Temperature Selection button will come on.
-
Press the Temperature Selection button.
-
Turn the Steam Control Dial to NO STEAM ( ).
-
Fill a metal or ceramic cup 1/3 full with cold milk. A stainless steel cup and skim milk are recommended.
-
Hold cup underneath Frothing Nozzle,leaving about 1/4 to 1/2 inch between the Nozzle and the bottom of the cup.
-
Turn Steam Control Dial counterclockwise to open steam valve. Milk is steamed when cup becomes warm.
NOTE: After each time steaming and to prevent clogging Nozzle, hold a cup with water under Nozzle and “steam” into the cup to clean. -
Turn Steam Control Dial to NO STEAM ( ). Press ON/OFF Button (light will go off); then press Temperature Selection button again to turn off steam temperature.
Unplug from outlet. Clean the Frothing Nozzle after each use.
How to Froth Milk
- Ensure there is water in the Removable Water Reservoir and move the Frothing Nozzle to the right of the unit.
- Plug into outlet. Press ON/OFF Button to begin heating water. When heated, the light next to Temperature Selection button will come on.
- Press the Temperature Selection button.
- Turn the Steam Control Dial clockwise to NO STEAM ( ).
- Fill a metal or ceramic cup 1/3 full with cold milk. A stainless steel cup and skim milk are recommended.
- Hold cup underneath Frothing Nozzle,leaving about 1/4 to 1/2 inch between the Nozzle and the bottom of the cup.
- Rotate Steam Control Dial about 3/4 turn toward steam. Hold cup under Frothing Nozzle until desired consistency is reached. Froth should be stiff and scoopable with a spoon.
- Turn Steam Control Dial to NO STEAM ( ). Press ON/OFF Button (light will go off); then press Temperature Selection Button again to turn off steam temperature.
Unplug from outlet. Clean the Frothing Nozzle after each use.
Care and Cleaning
WARNING Electrical Shock Hazard. Disconnect power before wiping exterior of unit or brew head. Do not immerse cord, plug, or machine in any liquid.
-
Turn Steam Control Dial to STEAM ( ) and empty any remaining liquid from Frothing Nozzle into container/cup of water.
-
Turn Steam Control Dial clockwise to NO STEAM ( ).
-
Wipe Nozzle. Every other use:
Remove nozzle tip with Wrench on Tamping Tool and wash in warm, soapy water. -
Place a container under Brew Head–it should be wide enough to catch water from both spouts. Press Pump Button and dispense at least 1 cup (237 ml) of water for best results.
-
Press ON/OFF Button to turn the unit OFF. The light next to the button will go off. Unplug from outlet.
-
Wipe exterior and Brew Head with warm water and damp cloth carefully — Nozzle may still be hot.
-
Wash all parts with warm, soapy water and dry thoroughly. DO NOT wash any parts in a dishwasher.
Recipes
Espresso
Brew one or two cups at a time following directions in “How to Use.”
Optional: Add sugar to taste.
Cappuccino
Mix 1/3 espresso, 1/3 steamed milk, and 1/3 frothed milk. Top with ground
nutmeg, ground cinnamon, powdered chocolate, or vanilla to taste.
Latte
Mix 1/2 espresso with 1/2 steamed milk. Top with ground nutmeg,ground
cinnamon, powdered chocolate, or vanilla to taste.
Iced espresso, cappuccino, or latte
Follow “Latte” instructions, then pour over ice.
Mocha
Mix 1 ounce (30 ml) thick chocolate syrup with 1/3 espresso. Fill with frothed
or steamed milk.
Tips for Making Espresso
-
For best results, use fresh-ground, dark, espresso roast coffee.
-
If preground espresso coffee is used, store the unused portion in an airtight container and keep in a cool, dark area for up to one week.
-
The grind of the coffee will affect the taste of the coffee and how the appliance works. If the grind is too coarse, water will flow too fast through the coffee and result in a weaker flavor. If the grind is too fine, the flavor may be too strong or bitter, and the grounds may clog the filter.
-
For hotter espresso, preheat the Filter Holder, the Ground Espresso Filter Holder, and the Pod Filter Holder by first brewing water into the cups for a few seconds and then emptying the brewed water.
CAUTION: The Filter Holder, the Ground Espresso Filter Holder, and the Pod Filter Holder are hot. -
Espresso beans may be ground in a coffee grinder. For best results, use the Hamilton Beach Custom Grind™ Coffee Grinder on the espresso setting. If grinding espresso in a store or using a burr mill, then use a setting that is one to two notches coarser than the espresso setting.
-
Grind your espresso so that it looks gritty, like salt or sand. It is too fine if it looks like powder and feels like flour. If the coffee is ground too fine, then the water will not flow through the coffee.
-
Espresso pods make it even easier to brew a great cup of espresso and cleanup is as easy as throwing out the used pod. Pods can be purchased at many local coffee houses and specialty housewares stores. A web search for “coffee pods” will also connect you with many coffee pod suppliers.
-
Always use cold water to make coffee. Warm water or other liquids could cause damage to the appliance.
Troubleshooting
Espresso will not flow out.
- Is the Removable Water Reservoir empty?
- Is the Removable Water Reservoir properly fitted into position?
- Make sure that the coffee grounds are not overpacked in the Filter.
- Is filter holder properly fitted into the Espresso Maker?
- Clean the Filter, Filter Holder, and Brew Head.
Machine is noisy when operating.
- Is the Removable Water Reservoir empty?
- Is the Removable Water Reservoir properly fitted into position?
- Is the Filter Holder properly fitted into position?
Espresso is too weak.
- Always use fresh espresso ground coffee and tamp the ground coffee down firmly.
- The longer the brew time, the weaker the espresso (1 serving = 1 to 1-1/2 ounces [28 to 42 g]).
- Be sure there is sufficient ground coffee in the Filter.
- Coffee grounds are too coarse.
- Try a different brand or roast of coffee.
Espresso is too strong or bitter
- Ensure Steam Control Dial is OFF. If the Steam Control Dial was left on, the water may have been too hot. Rotate Steam Control Dial counterclockwise to release steam into a frothing cup or pitcher and allow appliance to cool. Then repeat steps in “How to Use.”
- Too much espresso ground was used.
- Grounds were too fine.
- Brew longer before pressing ON/OFF Button to OFF.
- Try different a different brand or roast of coffee.
- Use the Hamilton Beach Custom Grind™ Coffee Grinder.
Difficult to froth milk.
- Always use fresh, cold milk (skim milk is recommended).
- Use a cold, stainless steel cup and move the cup slightly up and down while frothing.
- Clean the Frothing Nozzle.
- Make sure that the Temperature Selection Button is depressed and that the temperature/ready light is on.
- Trying to froth too much milk; reduce amount of milk in cup.
Steam runs out too quickly.
- Reprime the pump. See “Before First Use.”
Limited Warranty
This warranty applies to products purchased and used in the U.S. and Canada.
This is the only express warranty for this product and is in lieu of any other
warranty or condition.
This product is warranted to be free from defects in material and workmanship
for a period of five (5) years from the date of original purchase in Canada
and one (1) year from the date of original purchase in the U.S. During this
period, your exclusive remedy is repair or replacement of this product or any
component found to be defective, at our option; however, you are responsible
for all costs associated with returning the product to us and our returning a
product or component under this warranty to you. If the product or component
is no longer available, we will replace with a similar one of equal or greater
value.
This warranty does not cover glass, filters, wear from normal use, use not in
conformity with the printed directions, or damage to the product resulting
from accident, alteration, abuse, or misuse. This warranty extends only to the
original consumer purchaser or gift recipient. Keep the original sales
receipt, as proof of purchase is required to make a warranty claim. This
warranty is void if the product is used for other than single-family household
use or subjected to any voltage and waveform other than as specified on the
rating label (e.g., 120 V ~ 60 Hz).
We exclude all claims for special, incidental, and consequential damages caused by breach of express or implied warranty. All liability is limited to the amount of the purchase price. Every implied warranty, including any statutory warranty or condition of merchantability or fitness for a particular purpose, is disclaimed except to the extent prohibited by law, in which case such warranty or condition is limited to the duration of this written warranty. This warranty gives you specific legal rights. You may have other legal rights that vary depending on where you live. Some states or provinces do not allow limitations on implied warranties orspecial, incidental, or consequential damages, so the foregoing limitations may not apply to you.
To make a warranty claim, do not return this appliance to the store. Please call 1.800.851.8900 in the U.S. or 1.800.267.2826 in Canada or visit hamiltonbeach.com in the U.S. or hamiltonbeach.ca in Canada. For faster service, locate the model, type, and series numbers on your appliance.
To order parts:
US: 1.800.851.8900
www.hamiltonbeach.com
Canada: 1.800.267.2826
Mexico: 01 800 71 16 100
References
- Home | HamiltonBeach.ca
- Home | HamiltonBeach.com
- Home
- Home | HamiltonBeach.ca
- Home | HamiltonBeach.com