Comfort Zone CZ121 Series 12 Inch Table Fan User Manual
- June 8, 2024
- Comfort Zone
Table of Contents
Zone CZ121 Series 12 Inch Table Fan
User Manual
CZ121 Series 12 Inch Table Fan
Features:
- Wide Area Oscillation
- Push Button ON/OFF Switches with 3 Speed Settings
- High Performance Fan Blade
- Adjustable Tilt
- Safety Grilles
- 120V A.C. / 60Hz.
INTENDED USE:
This product is intended for indoor residential and office use only, not for
industrial or other commercial applications. Use only with electrical wiring
that is in good working order and that meets applicable codes and ordinances.
If you have any questions whether your wiring is adequate, consult a qualified
electrician.
While using your fan, you should follow the IMPORTANT INSTRUCTIONS listed
below. As part of those instructions, we have used the word “WARNING” to
indicate the level of hazard:
WARNING indicates a hazard which, if not avoided, could result in injury
or death.
IMPORTANT INSTRUCTIONS
As with all electrical appliances, basic safety precautions should always be followed to reduce the risk of electric shock, fire, or injury to persons, including the following precautions:
- Read all the instructions before using this fan.
- Use this fan only as described in this manual. Any other use not recommended by the manufacturer may cause electrical shock, fire or injury to persons.
- Do not operate the fan with a damaged power cord or after the fan malfunctions or has been dropped in any manner.
- Use of extreme caution is necessary when any fan is used by or near children, disabled persons or pets and whenever the fan is left operating unattended.
- Do not place the fan on a small, unlevel, uneven or any surface which might allow fan to tip or fall.
- For proper operation, fan should be placed on a smooth, non‑combustible, level surface.
- Always unplug fan when not in use, when moving from place to place, when assembling or disassembling parts, and before cleaning.
- The use of attachments, not recommended or sold by the manufacturer, may cause hazards.
- Do not use outdoors.
- Do not use fan in window. Rain may cause electrical hazard (for non‑window models).
- Do not operate the fan with blade guards or any safety device removed.
- Avoid the use of extension cords due to risk of fire. If an extension cord must be used, the cord must be minimum 14 AWG and rated not less then 1875 watts.
- Do not run power cord under carpeting. Do not cover cord with throw rugs, runners or the like. Arrange cord away from traffic area where it will not be tripped over.
- Do not insert or allow any object to enter any openings on the fan. Doing so may cause electric shock and/or fire hazard. Avoid contact with moving parts.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure they do not play with the appliance.
READ & SAVE THESE INSTRUCTIONS
WARNING: SHOCK HAZARD
Use your fan only in dry environments. This fan is not intended for use in a
bathroom, laundry area, or similar locations, or near sinks, washing machines,
swimming pools or other sources of water. Never locate fan where it may fall
into a bathtub or other water receptacle. Do not use in damp environments such
as flooded basements.
WARNING: HOT SURFACES
Do not touch fan motor when in use. This motor is hot when in use, to avoid
burns, do not let bare skin touch hot surfaces.
WARNING: FIRE HAZARD
Fans have arcing or sparking parts inside. Do not use near combustible
materials or flammable gases or sources of heat.
DO NOT USE in areas where gasoline, paint or flammable materials are used or
stored. To prevent a possible fire, do not block air intakes or exhaust in any
manner. Do not insert or allow foreign objects to enter any ventilation or
exhaust opening as this may cause an electric shock, fire, or damage the fan.
WARNING: ELECTRICAL SHOCK HAZARD
Do not use with damaged cord or plug. Use with adequate electrical system that
is up to code.
CAUTION: TO PREVENT ELECTRIC SHOCK, this product has a polarized two
prong plug (one blade is wider than the other) that must be fully inserted in
to a matching properly grounded outlet. This plug is designed to fit a
polarized outlet only one way. If the plug does not fit fully into the outlet,
reverse the plug. If the plug still does not fit, contact a qualified
electrician. Do not attempt to defeat this safety feature
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not use this
product with any solid‑state speed control device.
DO NOT operate any fan with a damaged cord or plug or after fan malfunctions,
has been dropped or damaged in any manner. Do not operate fan with a broken
blade, safety cage or any visual imperfections. Disconnect power before
servicing. For repairs covered under warranty, see warranty statement. For all
other repairs contact Comfort Zone® Customer Service by telephone or mail for
information and assistance.
DO NOT run power cord under carpeting. DO NOT cover cord with throw rugs,
runners or the like. Arrange cord away from traffic area where it will not be
tripped over. Avoid the use of extension cords due to risk of fire. If an
extension cord must be used, the cord must be minimum 14 AWG and rated not
less then 1875 watts. Do not use an extension cord unless the plug can be
completely inserted into its receptacle. Unplug the fan when not in use. Do
not operate fan with its ventilation obstructed.
USAGE:
Fan Operation: Always operate the fan in the upright position following
all instructions and recommendations listed in this manual.
Fan Location: Place the fan in the area of the room that will provide
proper fan cooling.
Fan Connection: Plug fan directly into 120 volt A.C., 60 Hz wall outlet.
Be sure plug fits tightly in outlet. A loose connection may cause overheating
and damage to the plug or fan.
Note: To prevent overloading a circuit, do not plug the fan into a
circuit that is servicing other electrical needs.
CONTROL PANEL
Turning Fan On/Off: Place fan on
stable level surface. Plug fan into properly grounded outlet. To start the
fan, press desired speed button: 1‑LOW, 2‑MED, 3‑HIGH. Press 0‑OFF to
discontinue use. Unplug fan when not in use.
Oscillation: To start fan oscillation, press Oscillation Control Knob
(located above motor housing) down.To stop oscillation function pull
Oscillation Control Knob up while the fan is in any oscillation position.
Fan Assembly:
Assembly is required to use this fan. Remove two (2) screws from base of
fan and save them for Step #2. Place power cord wire through opening of
plastic fan base. With cord opening properly positioned, snap plastic fan base
onto fan body. Re‑assemble screws removed in Step #1.
Remove the Blade Cap by twisting it CLOCKWISE while holding the
metal shaft tightly.
Note: Threads are reversed. Unscrew = Clockwise.
Assemble Rear Grille onto Motor Housing. Rear Grille should fit into
alignment pins on fan motor housing as shown.
Note: Wire Handle should be on top.
Thread Locknut onto Motor
Housing to lock Rear Grille in place. Tighten=Clockwise. Remove any protective
covering over shaft before fan blade installation. Place fan blade onto motor
shaft. Notice the pin on motor shaft should fit into slots of fan
blade.
Thread blade cap onto threaded end of
the motor shaft.
Note: Threads are reversed at this connection.
Tighten=Counter‑clockwise
With logo upright, attach Front
Grille to Rear Grille by snapping them together. Be sure all 8 clips are
secure. Do not operate fan without grille in place.
Care and Maintenance:
Cleaning: CAUTION‑Before cleaning the fan be sure to disconnect power
cord from the plug. Clean the grille surface with a clean damp cloth. Do not
use harsh chemical or abrasive cleaners. DO NOT IMMERSE THE FAN OR ANY WIRES
IN WATER. Replace front grille before fan use. Allow fan to dry completely
before use. Periodic grille cleaning with a vacuum will prevent dust build up.
The motor is sealed and does not require any interior maintenance, cleaning or
lubrication.
Maintenance: The Internal motor bearings are permanently lubricated at
the factory and do not require any additional lubrication.
Repair: DO NOT OPERATE THE FAN WITHOUT THE GRILLE IN
PLACE. DO NOT USE THE FAN IF IT HAS MALFUNCTIONED OR BECOME DAMAGED IN
ANY WAY.
Storage: Keep original carfton for storage of the fan. Coil and tie the
power cord to avoid damage during storage.
Note: Some models come with a plug where you can replace a fuse. If your
model has this, please read and follow the below instructions to replace the
fuse.
This product employs overload protection (fuse). A blown fuse indicates an
overload or short‑circuit situation. If the fuse blows, unplug the product
from the outlet. Replace the fuse as per the user servicing instructions
(follow product marking for proper fuse rating) and check the product. If the
replacement fuse blows, a short‑circuit may be present and the product should
be discarded or returned to an authorized service facility for examination
and/or repair.
Fuse Replacement:
- Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.
- Open fuse cover by sliding open fuse access cover on top of attachment plug towards blades. See Fig. 2.
- Remove fuse carefully. Use a small tool to pry the end of the fuse from holder cavity. Be careful not to break glass window.
- Replace fuse. WARNING: Risk of fire. Replace fuse only with identical 2.5 or 5.0 Amp, 125 Volt fuse (3.6mm x 10mm). Be sure fuse is properly seated within its cavity.
- Close fuse cover by sliding it back to its original closed position.
LIMITED WARRANTY
This unit is guaranteed to the original retail purchaser against defects in
quality or workmanship for a period of one year from the date of original
purchase. If this unit fails because of a manufacturing defect within 30 days
of purchase, return the unit, with your receipt, to the retailer. After 30
days, but within the warranty period, if the unit was purchased within the
continental United States, return it, freight prepaid, to World and Main for
repair or replacement. If the unit was purchased outside the continental
United States, return the unit to the place of purchase. This warranty does
not cover damage caused by misuse, abuse, overheating or alteration. Repairs
made by anyone other than World and Main are not covered in this warranty.
World and Main will not be held liable for any losses due to neglectful
operation. All implied warranties, including the warranties of merchantability
and of fitness of purpose, if applicable, are hereby limited in duration to
the period of one year from the date of original retail purchase. Some states
do not allow limitations on how long an implied warranty lasts, so the above
limitations may not apply to you. Incidental or consequential damages arising
from a breach of either express or implied warranties are hereby disclaimed
and excluded. Some states do not allow the exclusion of limitation of
incidental or consequential damages, so this limitation or exclusion may not
apply to you. Upon the expiration of this warranty all such liability will
terminate. No other warranties are expressed or implied.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state. No informal dispute settlement
mechanisms are available. This limited warranty is given in lieu of all other
warranties.
Manufactured for:
World and Main (Cranbury), LLC 324A Half Acre Rd.
Cranbury, NJ 08512 USA
800-221-6895
www.comfortzoneproducts.com
Rev. 08/31/2021
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>