FREEDOM 73050181 Mixed Materials Gate Instruction Manual

FREEDOM 73050181 Mixed Materials Gate

Read all instructions prior to installing product.
Refer to manufacturers safety instructions when operating any tools.

To register your product, please visit:
freedomproduct.com

WARNING:

• Improper installation of this product can result in personal injury. Always wear safety goggles when cutting, drilling and assembling the product.
• Incorrect installation may cause harm to the product or individual.
• Check local building codes to determine pool-safe fencing options.

NOTICE:

• DO NOT attempt to assemble the kit if parts are missing or damaged.
• DO NOT return the product to the store. For assistance or replacement parts call: 1-877-265-2220

BEFORE YOU BEGIN:

Check your local zoning laws.

1. Local zoning laws and Home Owners Associations may regulate the location, style and height of your fence or even require a permit signoff beforehand.
2. Check local codes for frost line depth and regulations.
3. Additional products and assembly may be required to meet wind code requirements.
   Notice of acceptance (NOA) can be found at www.miamidade.gov/building/pc- search_app.asp

Contact your local utilities companies.

• You must have the utility companies clearly mark your property for electrical, gas or water lines to avoid puncturing any unseen underground utilities.

TOOLS/MATERIALS NEEDED

| Post / Post Kits
---|---
| Infill Boards (Wood or Vinyl)
| Gate Latch
| Drill
| 2″ Spacer Blocks
| Level
| Tape Measure
| Safety Glasses

To obtain and review a copy of the warranty please visit barretteoutdoorliving.com.
You may also contact us at 1-877-265-2220 or email CS.outdoorliving@barretteoutdoorliving.com.

*NOTE:
Above chart reflects wood at 51⁄2″. Be sure to measure desired wood infill before installation.
If wood measures larger, less boards will fit in gate. It is recommended to let wood dry out prior to installation.

Gate opening is determined by width of gate plus clearance for hinge, latch, and drop rod (latch and drop rod sold separately); refer to latch and drop rod installation instructions for specific space requirements.

1. Gate uprights have a top and bottom route. Top route is 4-3/16″, bottom route is 3-1/8″ (Fig. 1).
2. Install bottom rail into bottom routed hole of the gate upright. Using two of the supplied hex head screws, align the screws with the 1/8″ inner holes as shown. Only install the outer screws at this step (Fig. 2).
3. Align the rails to be 90 degrees to the upright (Fig. 3).
4. Begin inserting infill boards (refer to chart for size & quantity) (Fig. 4).
5. Install top rail into lower upright and push flush to the top of the infill as shown. Add additional gate upright (Fig. 5).
6. Install remaining screws in all 4 corners to secure assembly (Fig. 6).
7. Install screw hole plugs in all four corners (Fig. 7). Install upright caps (may need to use rubber mallet to fully seat cap).
8. Using the hinge instructions, install the hinges 3-1/2″ to 4″ away from the top and bottom of the upright (Fig 8). Use a 2″ spacer block to rest gate on for ease of installation and to allow for space under bottom rail.
9. Follow hinge instructions to complete assembly.
10. Install gate latch (sold separately).

Barrette Outdoor Living
7830 Freeway Circle, Middleburg Heights, OH 44130
barretteoutdoorliving.com • 877-265-2220

References

• Barrette Outdoor Living: HomePage
• Fencing, Railing & Accents - Freedom Outdoor Living for Lowes
• Product Control Search - Miami-Dade County
• Untitled Document
• Product Control Search - Miami-Dade County

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>