FREEDOM 2×4 Decorative Screen Panel Frame Kit Instruction Manual

: June 4, 2024
: FREEDOM

Table of Contents

2×4 Decorative Screen Panel Frame Kit
BEFORE YOU BEGIN:
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

34117160
2×4
Decorative Screen Panel
Frame Kit
INSTALLATION INSTRUCTIONS

2×4 Decorative Screen Panel Frame Kit

**** Read all instructions prior to installing product.
Refer to the manufacturer’s safety instructions when operating any tools.

To register your product, please visit:
freedomproduct.com

WARNING:

Improper installation of this product can result in personal injury. Always wear safety goggles when cutting, drilling, and assembling the product.
Incorrect installation may cause harm to the product or individual.
Check local building codes to determine pool-safe product options.

NOTICE:

DO NOT attempt to assemble the kit if parts are missing or damaged.
DO NOT return the product to the store. For assistance or replacement parts call: 1-888-418-4400.

BEFORE YOU BEGIN:

Check your local zoning laws.

Local zoning laws and Home Owner’s Associations may regulate the location, style, and height of your product or even require a permit signoff beforehand.
Check local codes for frost line depth and regulations.
Additional products and assembly may be required to meet wind code requirements. Notice of acceptance (NOA) can be found at
www.miamidade.gov/building/pc-search_app.asp Contact your local utilities companies.
You must have the utility companies clearly mark your property for electrical, gas, or water lines to avoid puncturing any unseen underground utilities.
NOTE:
Installation is best accomplished with two sets of hands.

TOOLS/MATERIALS NEEDED:

| Drill
---|---
| Pencil
| Tape Measure
| Rubber Mallet
| 3″ Spacer Blocks
| Level

SOLD SEPARATELY:

| (3) 2×4 Decorative Screen Panels
---|---
| 3/8″ Bolts/Screws

(For surface mounting)

2×4 Frame Kit Component list:

QTY.	Description
2	2″ Aluminum Posts
2	Top/Bottom U-Channels (Rails)
2	Mid H-Channels (Rails)
2	Base Plates
2	Post Caps
1	#2 Square Drive Drill Bit
1	1/8″ Pre-Drill Bit
1	#3″ Phillips drill bit
2	Base plate trim ring covers
4	Plastic push plugs (for the trim ring covers)
8	2 1/2″ Phillips screws (for base plate
8	#8 Square drive screws

To obtain and review a copy of the warranty please visit Freedomproduct.com/warranty.
You may also contact us at 1-888-418-4400 or email cs.outdoorliving@barretteoutdoorliving.com.

Determine where you would like to install the frame kit. Make sure the posts will be held in place by a solid structure and if necessary, reinforce the surface it is attaching to.
Install base plates to the bottom of posts. Locate the bottom post with pre-tapped holes and attach the bottom plate to that end. Using the #3 Phillips drill bit (included), screw the base plate to the bottom of the post (Fig. 1). Posts are partially threaded on one end of the post (3/4″). While installing screws, you will feel resistance at the 3/4″ mark for a tighter, more secure fit. Install screws until they’re flush with the plate (Fig. 2).
TIP: Drill should be set to low speed when securing plates to post.
Set the first post in the desired location. Use the base plate to mark the holes for the surface mounting plate. Mark and drill holes for appropriate 3/8″ fasteners (fasteners will vary depending on mounting surface). Attach post/base to surface using appropriate 3/8″ fasteners.
NOTE:
Keep in mind ceiling clearance if installed inside. Attaching post/base to surface may need to wait until the end of installation if full assembly must be tilted for all 3 panels to be installed properly.
Place two 3″ spacer blocks to support the bottom U-channel. A 3″ spacer block is used to allow the proper finished height of the top rail. Take U-channel and insert into the channel of the first post, resting on the 3″ spacer blocks (Fig. 3).
NOTE:
This step is to set the distance in between posts. Be sure to use the U-channel rail and not the H-channel rail as the bottom rail.
Take the second post and insert the opposite side of the bottom U-channel rail into the channel of this post. Be sure the rail is fully inserted into the post. If not fully inserted the predrilling process will not be successful. Lock the second post into position by repeating Step 3.
NOTE:
If connecting more than one frame kit together, line or corner posts are available (sold separately).
Locate where to pre-drill a hole through the post and rail (Fig. 4). Pilot holes for screws should be located directly at the intersection of the small groove of the post and the channels. Using the 1/8″ drill bit provided, pre-drill the pilot hole as indicated above.
Then, using the #2 square drive bit provided in the kit, secure a #8 square drive screw into both posts, securing posts and rails together. (Fig. 5). Remove 3″ spacer blocks.
Install the screen by sliding down the channels on either side of the posts (Fig. 6) and into the channel of the bottom rail.
NOTE:
The screen will be loose in the posts and the bottom rail. This is designed to allow the screen to expand and contract during the heating and cooling of the day.
Slide rail (H-channel) in the groove from the top, resting it on the top of the Decorative Screen Panel. Lift H-Channel about 1/8″ (to allow for expansion and contraction), then pre-drill a hole following the same process in Step 6. The screw should be installed directly on the small groove of the post, connecting with the H-channel. (Fig. 7).
Repeat steps 7 & 8 for the middle and top panel (Fig. 8).
NOTE:
Always use a tape measure to verify rails are equal space from each other and that they are level.
Place post caps on top of posts (lining up the tabs underneath the holes in the post). Using a rubber mallet, fully seat the cap onto the post (Fig. 9).
NOTE:
If installing additional frame kits (line or corner), install these prior to placing post caps on posts.
To connect additional frame kits, line and corner extension kits are available.
Assemble trim ring over plate. Take one side of the trim ring and push the plugs through the holes underneath. Take the second half of the trim ring and push it together (Fig. 10).