freedom WON E-Tower LiFePO4 Battery 5kW 48V Instructions
- June 3, 2024
- freedom WON
Table of Contents
Freedom Lite to Inverter Interfacing
Guide
E-Tower LiFePO4 Battery 5kW 48V
Freedom Won produces various ranges of the popular eTower and Freedom Won LiTE battery to suit all applications. The respective battery ranges available are as follows:
- eTower
- LiTE Home and Business
- LiTE HV Home and Business
- LiTE Marine (13V, 26V and 52V)
- LiTE Mobility (golf carts, forklifts etc)
- LiTE Commercial (including Lite Commercial HV and HV+)
- LiTE Industrial
For the Freedom Won general purpose 12 V LiFEPO4 batteries not covered here
please refer to the 12V battery specification sheet for more information.
The focus of this guide is to summarize the inverter and allied equipment
brands that are certified to be compatible with tower and Freedom LiTE
batteries. The interface option covered relates only to the CAN bus or RS485
communication option. For interfacing with analogue and relay drivers in the
Marine range please refer to the Lite Marine installation manual.
The CAN bus or RS485 interface is not the only consideration when determining
the marriage suitability of an tower of LiTE and an inverter – the operating
voltage and power capabilities must also be matched.
All CAN or RS485 networks must contain two 120 Ohm termination resistors;
every LiTE is supplied with one resistor to fit into the second RJ45 CAN Bus
socket on the battery, some inverter systems require the addition of another
resistor and some have one built in. The eTower master module that the
inverter CAN Bus or RS485 will be connected to has a built in termination
resistor on the CAN Bus and RS485.
Some systems require a specially made RJ45 cable to accommodate varying pin
configurations when connecting to the inverter – these can be purchased from
Freedom
Won or made by yourself by referring to the LiTE manual for the pin
configuration. The eTower batteries are all shipped with a selection of
cables that provides a solution for most inverters on the market and therefore
purchasing separate cables is not necessary.
Some inverter systems require a special profile on the eTower or LiTE. If you
require this, please contact Freedom Won for assistance.
Refer to the respective eTower or LiTE installation manual for further
information on CAN bus communication.
The natural classification for laying out this guide is to split the eTower
and LiTE ranges into the following categories based on their nominal operating
voltage:
I. 52V and below (this means 13V, 26V and 52V)
II. 150 to 300V
III. 300 to 600V
IV. 600V to 800V
Table 1 provides the inverter and interfacing information for all inverters
certified by Freedom Won in each of the above four categories.
Inverter brands not included in Table 1 have not been certified by Freedom Won
for the CAN bus or RS485 interface. Should you have another brand of CAN bus
or RS485
compatible inverter that you would like to connect to an eTower or LiTE please
contact Freedom Won, we would be glad to assist.
There are also a few inverter brands that are not CAN Bus or RS485 enabled and
hence have no way to communicate with the eTower or LiTE. These inverters will
also work in a system with the eTower or LiTE, but some functionality will be
lost because of the lack of information and commands available from the
battery. For example, the true SoC of the battery will not be available on the
inverter, and the battery will also not be able to stop charge or discharge
should it be necessary. The battery will trip to protect itself if this
occurs, so there is no safety concern, only a matter of inconvenience. For new
installations Freedom Won recommends selecting a CAN Bus or RS485 lithium
battery compatible inverter. For retrofits where an inverter without CAN bus
or RS485 already exists, the eTower or LiTE can be used, provided that the
inverter voltage setpoints are set up correctly – contact Freedom Won for
assistance if the eTower or LiTE manual does not provide you with enough
information.
The Freedom Won eTower comes with the following inverter cables included:
- CAN Bus Comms cable for Victron inverters
- CAN Bus Comms cable for Type 1 inverters (eg. Sunsynk, Solis, Goodwe, Growatt, Revo)
- RS485 Comms cable for Voltronic/Axpert inverters
Refer to the respective inverters’ installation manual to confirm connector
type required.
Table 1: Inverter Interfacing Guide Categorized according to Voltage
Range Categories
Category| eTower & Freedom LiTE Models| Equipment/
Battery Inverter Brand| Equipment Models| Installation Notes
---|---|---|---|---
I.(13V,26V,52V)| eTower (52V) Freedom LiTE Home and Business (52V)Freedom LiTE
Commercial (52V) Freedom LiTE Marine (13V, 26V, 52V)| Axpert/Kodak| King, Max,
VMIII48V models to suite 52V LiTE and eTower| For LiTE models a CAN Bus to
RS485 Converter accessory is required, available from Freedom Won or certain
distributors. Refer to Freedom Won CAN to RS485 Converter installation guide
for complete setup information for this inverter. Standard LiTE Profile.
Standard Ethernet Cables. No additional resistor. Select “Lib” (for Lithium
Battery) in inverter menu under battery type. For eTower models simply plug
the inverter RS485 to the correct eTower RS485 plug using the cable supplied
with the eTower.
Goodwe| ES48V models to suite 52V LiTE and eTower| “LiTE to Type 1” RJ45 cable
required for connecting CAN bus from LiTE to Goodwe – available from Freedom
Won. Standard LiTE Profile.
No additional resistor.
Select Default Lithium 100Ah in the Goodwe app (or Freedom Won if available).
For eTower connect CAN Bus using “Type 1” cable supplied with the eTower.
Growatt/Sunforce| 5kW48V model to suite 52V LiTE and eTower| “LiTE To Type 1”
RJ45 cable required for connecting CAN bus from LiTE to inverter – available
from Freedom Won. Standard LiTE Profile.
No additional resistor.
For eTower connect CAN Bus using “Type 1” cable supplied with the eTower.
Imeon| 3.6, 9.1248V models to suite 52V LiTE and eTower| “Type Imeon” RJ45
cable required for connecting CAN bus from LiTE to Imeon inverter – available
from Freedom Won Non-Standard “Imeon Profile” required on LiTE
For eTower connect CAN Bus using “Type 1” cable supplied with the eTower.
| | Ingeteam| Ingecon Sun Storage 1Play 3TL and 6TLSemi Compatible with 52V
LiTE| Note: operating these inverters on 52V is possible but the battery
current is limited by the inverter to 50A and therefore the maximum battery
power available from the inverter is about 2.5kW. Standard Ethernet cable can
be used for the CAN bus – the inverter end has no plug, only wire terminals
(see Lite manual for the cable configuration)
Non-Standard “Ingeteam Profile” required on LiTE No additional resistor
required
Note: The Lite cables will not fit into the terminals directly on the Ingeteam
Inverter as the terminals are too small. Note: These inverters cannot be
connected in parallel or 3-phase owing to limitations to the Ingeteam
firmware. eTower is not compatible.
---|---|---|---|---
Koyoe| 3kVA Hybrid48V models to suite 52V LiTE and eTower| Contact Freedom Won
if you need to connect one of these inverters to a LiTE
MLT| PowerStar10 Oasis Nomad MPPT48V models to suite 52V LiTE and eTower| The
MLT range of products offers complete CAN bus interfacing from the 2019 models
onwards.
PowerStar10 – Use a “LiTE to Type 1” RJ45 Ethernet Cable available from
Freedom Won. The inverter includes a 2 pin jumper header to enable the
termination resistor if it is the last in the CAN bus line.
Oasis – same as PowerStar
Nomad – A CAN terminal plug is provided on the PC board of the Nomad with a
resistor that can be enables with a bridge (see Nomad manual)
Standard Lite Profile
For eTower connect CAN Bus using “Type 1” cable supplied with the eTower.
Revo| 5kVA48V models to suite 52V| Requires “Type 1” CAN Bus cable available
from Freedom Won. Standard Lite Profile No additional resistor required
| | | LiTE and eTower| For eTower connect CAN Bus using “Type 1” cable
supplied with the eTower.
---|---|---|---|---
SMA| Sunny Island48V model to suite 52V LiTE and eTower| “Type SMA” RJ45 cable
required Standard Lite Profile
Additional resistor supplied with inverter For eTower connect CAN Bus using
“eTower to Type SMA” cable available from Freedom Won.
Sofar Solar| 3kW48V models to suite 52V LiTE and eTower| Please contact
Freedom Won if you have a Sofar Solar 48V inverter to connect to a LiTE
Solax| Various48V models to suite 52V LiTE and eTower| Please contact Freedom
Won if you have a Solax to connect to a LiTE
Solis/Kodak| 3 to 6kW models 48V models to suite 52V LiTE and ETower| “LiTE to
Type 1” RJ45 cable required for connecting CAN bus from LiTE to inverter –
available from Freedom Won. Special “Solis” LiTE Profile required from Freedom
Won.
No additional resistor.
For eTower connect CAN Bus using “Type 1” cable supplied with the eTower.
Studer| Variotrack and Xtender models 48V models to suite 52V LiTE and eTower|
System must include an XCom CAN module and RC3 module. Connect Lite CAN to
XCom CAN module and set the XCOM CAN dip switches according to the pin
configuration required (see Lite Manual for Lite CAN pin configuration)
Standard Lite Profile Termination resistor dip switch available on XCOM CAN
device.
For eTower connect CAN Bus using “Type 1” cable supplied with the eTower.
Sensing/Daye| 5kW and 8kW Hybrid48V models to suite 52V LiTE andeTower| “Type
1” CAN RJ45 cable required. No additional resistor required. Select Battery
Type 00 on the Sensing/Daye Standard Lite Profile required For eTower connect
CAN Bus using “Type 1” cable supplied with the eTower.
| | Victron| Quattro, MultiPlus
Models available in 12V, 24V and 48V to suite the LiTE Marine 13V, 26V and
52V models respectively48V Victron models suite the LiTE 52V and eTower
models| All Victron systems must include a Venus device i.e. Venus GX, Color
Control GX, Cerbo, Octo GX, Maxi GX. This is required to interface the LiTE
with the inverter over CAN Bus. Use a standard ethernet cable to connect the
Lite CAN bus to the Venus Ve.CAN. Standard LiTE Profile
Termination resistors supplied with Venus device See Freedom Won Compatibility
Guide on the Victron Energy website for further information.
For eTower connect CAN Bus using “Victron” cable supplied with the eTower.
---|---|---|---|---
II. (150V to 300V)| Freedom Lite Home and Business HV| Ingeteam| Ingecon Sun
Storage 1Play 3TL and 6TL| The original Freedom Lite Home and Business HV
range was specifically designed for the Ingeteam inverters. The Ingeteam
inverters are very efficient and compact covering high performance for a
residential solution – full power is available from the inverter when
operating on battery owing to the higher DC voltage.
Standard Ethernet cable can be used for the CAN bus – the inverter end has no
plug, only wire terminals (see Lite manual for the cable configuration)
Non-Standard “Ingeteam Profile” required on Lite
No additional resistor required
The Lite Home HV cables will fit into the terminals on the Ingeteam Inverter
as the terminals HV cables are much smaller owing to lower current.
Note: These inverters cannot be connected in parallel or 3 phase owing to
limitations to the Ingeteam firmware.
III.(300V to 600V)| Lite Home and Business HV+ (Note only HV+ models not HV
models)| ATESS ATESS inverters Available from Freedom Won| Hybrid
battery inverters 30kW to 150kW:| Note: Only 40/32HV+ upwards is compatible
with these inverters i.e. not the 30/24HV+
Standard ethernet cable for CAN Bus (connects to terminals in the inverter)
“ATESS Lite Profile” required
| Lite Commercial HV| with Lite HV battery purchase| HPS30, 50,
100 and 150| No additional termination resistor required. Inverters available
from Freedom Won along with design, installation, and commissioning
assistance.
---|---|---|---|---
| Sofar Solar Inverters available from Freedom Won| 20kVA 3 Phase|
Note: 30/24HV+ is compatible with slight power derating owing to lower than
ideal voltage. All other Lite Home and Business HV+ models offer full
performance. Standard ethernet cable for CAN Bus (connects to a terminal
multipion plug on the inverter) “Sofar Solar Lite Profile” required No
additional termination resistor required
IV. (600V to 800V)| Lite Commercial HV+ Lite Industrial| ATESS ATESS
inverters Available from Freedom Won with Lite HV+ battery purchase|
Battery Inverters 50kW to 630W PCS50, 100, 250, 500, 630| This is a pure
battery inverter range designed to couple with DC solar charge controllers
(PBD 250 and 350). Freedom Lite must be an HV+ model. Lite requires “ATESS
Lite” profile. Standard ethernet cable required. No additional resistor
required. Inverters available from Freedom Won along with design,
installation, and commissioning assistance.
| Socomec| Various models available – typical range 100 kW to 500kW| Contact
Freedom Won for assistance with interfacing with this brand
| Elpower| Various Models available – typical range 100kW to 500kW| Contact
Freedom Won for assistance with interfacing with this brand
| ABB| MGS100 – various sizes| Contact Freedom Won for assistance with
interfacing with this brand
| Delta| PCS2000 range| Contact Freedom Won for assistance with interfacing
with this brand
| Kehua| Various models – 100kW to 1,5MW| Contact Freedom Won for assistance
with interfacing with this brand
Freedom Won Technical Contact Details
Please use the following contact details to make enquiries on technical
matters or for actual
technical support with design and/or commissioning:
Email –support@freedomwon.co.za
Mobile – +27 60 968 5145
Please contact the Freedom Won office for urgent assistance if the mobile
number is
temporarily engaged or unavailable
(seewww.freedomwon.co.za for contact
details).
References
- LiTE energy storage products and solutions - Home - FREEDOM WON
- LiTE energy storage products and solutions - Home - FREEDOM WON
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>