moa Electric Fireplace Instruction Manual

moa Electric Fireplace

BEFORE USE

Please read and follow all instructions carefully before use. Failure to follow these intstructions could result in bodily injury, and/or property loss. Retain instruction manual for future use.

IMPORTANT

• We suggest you spend a short time reading this instructions and then follow the simple step-by step instructions.
• Carefully check that you have all the parts before beginning assembly.
• Keep small parts and fittings out of children’s reach and keep children well away from construction area, as the unassembled product contains small parts, which could present a choking hazard.
• We suggest you retain these instructions for future reference.
• A minimum of two persons are required to hang the Glass Wall Fire­place.
• Always ensure intended wall area to be drilled is free from any hidden electrical wires, water and gas pipes.
• Please use suitable wall fixings for your wall type.
• Not suitable for use in bathrooms.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and under­stand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• If the supply cord is damaged, it must be replaced by the manufactur­er, its service agent or similarly qualified persons in order to avoid a hazard.
• WARNING: In order to avoid overheating, do not cover the heater.
• The heater must not be located immediately below a socket-outlet.
• Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool.
• Children of less than 3 years should be kept away unless continuously supervised.
• Children aged from 3 years and less than 8 years shall only switch on/ off the appliance provided that it has been placed or installed in its in­tended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and under­stand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.
• CAUTION: Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.

PRODUCT INFORMATION

Made from metal, tempered glass and plastic.

CARE INSTRUCTIONS

• We suggest you make periodic checks to ensure all screws are fully tightened.
• Product must be assembled on o Aot, level surface.
• For general cleaning, dust weekly with a soft lint free cloth.
• Any spills should be removed immediately with a soft clean damp cloth ond dried immediately.
• Do not use obrosive cleaning products or those containing silicone.
• Avoid keeping furniture in direct sunlight or close to ony heot source os this can cause cracking, discolouration or warping.
• Periodically check all fixings and tighten ii necessary
• Clean using a glass cleaner and soft cloth.Do not use cleaning products containing obrosives os these will scratch hot stond.
• Do not ploce very hot or very cold items ogoinst or in close proximity to panel surface unless adequately thick insulation material is used to prevent such items from coming into contact with ponel.
• Do not strike the ponel with hord or pointed items.
• Do not rub or scrub the surface when cleaning.
• For general cleoning,dust regularly with o soft cleon cloth.
• Not suitable for use in bathrooms.
• Periodically check all fixings and tighten if necessary.

Warning

• We strongly recommend that a professional who has experience of fitting such items should install Wall Fireplace.
• Wall Fireplace are heavy objects and your safety is dependant on the construction/strength of the wall to which it is attached.
• We would recommend that the following methods be used to hang the Wall Fireplace.
  • At least two people are recommended to install the Wall Fireplace.
  • Wall fixings must be used for stability on this item and for safety rea­son the Wall Fireplace should not be left freestanding.

SAFETY INSTRUCTIONS

• Incorrect operation and improper use can damage the appliance and cause injury to the user.

• The appliance may be used only for its intended purpose. No responsibil­ity can be taken for any damage caused through incorrect use or improper handling.

• Before connecting the appliance to the electrical source, check that the current and power match those given on the rating plate.

• Do not put the appliance in water or any other liquid. However should the appliance accidentally fall into water or have water or any other liquid spilt over it isolate and unplug the appliance immediately and have it checked by a qualified person before using it again.

• Non-observance could cause a fatal electric shock!

• Never attempt to open the lire chassis by yourself.

• Do not place any kind of object into the inside of the housing.

• Do not use the appliance with wet hands, on a damp floor or when the appliance itself is wet.

• Do not touch the plug with wet or damp hands.

• Check the cord and the plug regularly for any possible damage. If the cord or plug is damaged, it must be replaced by the manufacturer or a qualified person in order to avoid a hazard.

• Do not use the appliance if it is dropped or otherwise damaged or if the cord or plug are damaged. In the case of damage repair must be undertaken by a competent person.

• Never attempt to repair the appliance yourself. This could cause an electric shock.

• Do not allow the cord to hang over sharp edges and keep it well away from hot objects and naked Aames. Remove the plug from the
  socket by pulling the plug, not the lead.

• For extra protection it is possible to fit the electric household installation with a fault current breaker with a rated breaking current of not more than 30mA. Ask your electrician for advice.

• Make sure that there is no danger that the cord or extension cord may inadvertently be pulled or cause anyone to trip when in use.

• If an extension cord is used it must be suited to the power consumption of the appliance, otherwise overheating of the extension cord and /or plug may occur.

• This appliance is not suitable for commercial use nor for use in the open air.

• Never leave the appliance unattended while it is in use.

• Children cannot recognize the dangers involved in the incorrect use of electrical appliances. Therefore never allow children to use household appliances without supervision.

• Always remove the plug from the socket when the appliance is not in use and each time before it is cleaned.

• Danger! Nominal voltage is still present in the appliance as long as the appliance is connected to the electrical source. Always unplug when not in use.

• Switch the appliance off before disconnecting from the electrical source.

• Never use the cord to carry the appliance.

• The unit should not be mounted underneath a shelf.

SPECIAL SECURITY ADVICE

• Maintain a minimum distance of 1 m to furniture, curtains and other flam­mable materials.
• Do not place the appliance underneath a power socket.
• Do not use the appliance in rooms in which highly Aammable materials such as gas, paints, gasoline, solvents, etc. are stored.
• To avoid overheating and fire, never cover the appliance and its vents.
• Do not use the appliance in bathrooms, laundry rooms or other equally moist places.
• Do not place the power cord underneath carpets etc.
• The warm air vent becomes very hot during operation. During operation, only touch the appliance’s switches and handles.
• The appliance must not be moved when hot. Never touch the hot parts with your bare skin.
• Spare components (for installation by competent electrical engineers) may also be available from the supplier.

RATING INFORMATION

Appliance Data: MOA201 F, MOA201 F B, MOA202FB, MOA208F, MOA208FB
Supply Voltage: 220-240¥~ 50
Heating Elements: 2000W
Lighting: 6-10 W LED Bulb (Total)

Fittings

PARTS

Fire suite

ASSEMBLY INSTRUCTIONS

Step One

• Fitting of Wall Hung Fire Caution
• Do not connect the appliance to the electrical supply at this time.
• The screws and plugs supplied with this package are only suitable for SOLID wall installation. For any walls other than solid, such as cavity, the appropriate fixings MUST be used.
• Unpack the appliance, carefully lift the surround from the carton and stand upright.
• Decide on the position where the suite will hang on the wall and determine a height for the fire to be fixed. {110cm to 120cm from the Aoor to the top screw fixings is a recommended height).

Step Two

1. Drill the holes (07mm) in the wall according to Figure 1 and Figure 2. Distance between the holes should be 586mm.

2. Use 2 wall plugs and 2 05 x 35mm screws provided and screw the screws into the 2 holes, leaving the end of the screws with 10mm protrud­ing from the wall.

3. Offer the appliance up into position, the 2 keyhole slots (see
   Figure 2) at the back of the suite will sit over the 2 screws protruding from the wall. Ensure the fire is level.

4. Unpack the pebbles and arrange them over the tray. You can adjust the position of the pebbles as you require (see Diagram B). Note that these pebbles should be kept away from children.

Step Three
Fitting the Front Frame to the Engine
Note: Only fit the glass front to the fire alter fire has been securely fitted to the wall.

1. Carefully hang the glass front to the hooks on the sides of the fire. See Figure 3.

2. Check the product periodically to ensure that no fittings has loosened and needs attention.
   WARNING:
   Always ensure intended wall area to be drilled is free from hidden electrical wires, water and gas pipes.

OPERATION INSTRUCTIONS

Power Switch (O/I)
The main Power Switch must be turned ON in order to operate by Remote Controller or Manual Control Board.
If the power switch was turned off, then all functions off, while settings would be reserved For one week.
When the fireplace is not in use or is to be deaned or maintained, the main power switch must be turned off, and the plug should be removed.

A. On/Off

• Note: When power switch was turned on, the fireplace was on standby status and indicator Power is on.
• Press ON/Off button once, the Acme would be turned on at level 3(high), and indicator Acmes is on.
• Press ON/Off button again, all function turned off and the unit be on standby status.
• Press and hold this button 3 seconds, then all settings would be cancelled, and initialized.

B. Flame/Ambient
Flame brightness could be adjusted at 3 levels circularly, display as -1, -2, -3.
Press button once and the Aame effect will be illuminated at level 1, and indicator flames is on.

1. Press twice and the Aame effect will be illuminated at level 2, and indicator flames on.
2. Press three times and the Aame effect will be illuminated at level 3, and indicator Aames on.

Press and hold this button 2 seconds, and the ambient light would be turned on. Then user can change the ambient light by pressing the button circularly (7 colors optional, Red, Yellow, Green, Purple, Blue, Pink, White).
Press and hold this button 2 seconds again, it would switch back lo control the Aame brightness.

C. Heat
Note: This function might be effected by “Adaptive Start” or “Weekly Setting” function. Please make sure that “Adaptive Start” or “Weekly Setting” function were turned off, or not on, before use the heating function separately. Those two functions could be turned off by pressing on/off button.
Press this button once, 1 000W heater ON, and single indicator starts flashing.

1. Press twice, 2000W heater ON, and double indicator Aashing.
2. Press this button three times, it would turn OFF heater.

This button would also be used as “Confirm”or “OK” on “Adaptive Start”,”Time Calibration” and “Weekly Setting” Mode. (details as below)

D. Temp.(Adaptive Start)
Note: Room temperature could be setted without turning on the heater.
Press this button to set room temperature at 18C/65F, 21 C/70F, 24C/75F, 27C/80F, 30C/85F circularly.

1. Press Up or Down button to select the room temperature, and press Heat button to confirm.
2. Press On/Off button to cancel or turn off Adaptive Start function.
   Press and hold this button 2seconds to switch C/F.

Adaptive Start Function

1. If room temperature is detected lower than set temperature, the heater would auto-start to work.
2. While if room temperature is detected higher than setted temperature, the heater would be turned off automatically.
   Note: Settings under this mode might effect the function of “Weekly Setting”.
   This button would also be used as “UP” selection on “Adaptive Start”,”Time Calibration” and “Weekly Setting” Mode. (details as below).

E. Timing
Press this button to set the working time from 1 ~24 hours circularly. Number would be displayed on control board.

1. Press this button once and number “l” displayed, and indicator timer on. And then
2. Press Up or Down button to select the working hours you want, and press Heat to confirm.
3.  Working time setting would be cancelled if “-:-” was selected.

Note:

1. Timing setting only be applicable when Flame and/or Heat function on
2. When working time reached set time, the unit would be automatically turned off and on standby.
3. When there is conAict on this set time and the Cut-off time under
   “Weekly Setting” mode, the unit would be turned off as per the time whichever occurs earlier.

Press and hold this button 2seconds to enter Time Calibration mode.

1. The control board would display “00:00”, and user could start to correct time by pressing button Up and Down.
2. Then press Heat button to confirm the time correction, and move to date correction. “dl” would be displayed.

E. Timing
3) Correct date by pressing button Up and Down, and press Heat to confirm and complete the Calibration.

Note:

1. Indicator Timer would be on during time calibration.
2. “dl “=Monday, “d2″=Tuesday ……… “d7″=Sunday

F. Set Up(Weekly Setting)

Press this button to enter Weekly Setting mode, and indicator Date on.

1. Firstly select the date by pressing Up and Down button from “d 1” to “ALL”.Press Heat to confirm your selected date, and enter Start-up Setting mode on selected date,indicator Date on.

2. Press Up and Down to set Start-up Time(Hour). Press Heat to confirm and move to Start-up Time(Minutes) setting.
   Press Up and Down to set Start-up Time(Minutes). Press Heat to confirm and move to Cut-off Time(Hour) setting, and indicator Off is on.

3. Press Up and Down to set Cut-off Time(Hour). Press Heat to confirm and move to Cut-off Time(Minutes) setting.
   Press Up and Down to set Cut-off Time(Minutes). Press Heat to confirm and move to Room Temperature setting, and indicator C or F on.

4. Press Up and Down to set Room Temperature. Press Heat to confirm, and complete setting on the selected date.

F. Set Up(Weekly Setting)

Note:

1. User can set Room Temperature and Start-up/Cut-off Time of every day.
2. User can make setting on other days by repeating the procedure above.
3. If “ALL” selected, it means that the fireplace would conduct the same setting everyday.
4. “dl “=Monday, “d2″=Tuesday ……… “d7″=Sunday, “ALL”=Whole week selected.
5. When heater is on, then “Start-up” Time setting is invalid, while “Cut­off” Time setting is valid.
6. When there is conAict on “Timered Time” and the Cut-off time under “Weekly Setting” mode, the unit would be turned off as per the time whichever occurs earlier.
7. When the Adaptive Start temperature is setted lower than that temperature setted under “Weekly Setting” made and/or detected room temperature, the heater would not be turned on.
   When there was any setting made, indicator Date would be on, or the indicator would be off.
   Press and hold this button Setup 3s, all settings would be cleaned and initialized.

MAINTENANCE

Safety Cut -Out System
This appliance has a safety cut out system, which will activate if the air inlets or outlets are obstructed and the fire begins to overheat. The appli­ance will work again automatically when the temperature comes down.

Environmental Protection
Correct disposal of this product.
This symbol on the product,or in its packaging,indicates that this product may not be treated as household waste. lnstead,it should be taken to the appropriate waste collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly,you will help prevent potential negative con­sequences for the environment and human health,which could otherwise be caused by the inappropriate waste handling of this product. For more detailed information about the recycling of this product,please contact your local council, your househould waste disposal service,or the shop where you purchased the product.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>