BALLUFF BNI IOW-560-W01-K022 Instruction Manual

June 8, 2024
BALLUFF

BALLUFF - logo BNI IOW-560-W01-K022
Instruction Manual

BNI IOW-560-W01-K022

Network interface
** The CE Mark verifies that our products meet the requirements of the current EU Directive.
About this guide**
This guide provides all the information required for safe use of the IO-Link Wireless Bridge.
It applies to the following models:

  • BNI IOW-560-W01-K022

Intended use
The IO-Link Wireless Bridge converts IO-Link to IO-Link Wireless and connects a wired IO-Link device via IO-Link Wireless to an IO-Link Wireless Master. The device can be an IO-Link sensor, an IO-Link actuator or an IO-Link hub. The IO-Link Wireless Bridge is intended for use in industrial applications.
Flawless function in accordance with the specifications in the technical data is ensured only when using suitable original Balluff accessories. Use of any other components will void the warranty.
The module may only be operated with an approved power supply. Only approved lines may be connected. Non-approved use is not permitted and will result in the loss of warranty and liability claims against the manufacturer.
Reasonably foreseeable misuse
The product is not intended for the following applications and areas and may not be used there:

  • In safety-oriented applications in which personal safety depends on the device function
  • In explosive atmospheres
  •  in domestic settings (product is class A (EMC limit) for the industrial sector)

Other applicable documents
A comprehensive user’s guide and additional information about this product can be found at www.balluff.com on the product page.

Safety notes

Activities such as installation, connection and startup may only be carried out by qualified personnel.
Qualified personnel are persons whose technical raining, knowledge and experience as well as knowledge of the relevant regulations allow them to assess the work assigned to them, recognize possible hazards and take appropriate safety measures.
The operator is responsible for ensuring that local safety regulations are observed.
In particular, the operator must take steps to ensure that a defect in the product will not result in hazards to persons or equipment.
The product must not be opened, modified or changed. If defects and unresolvable faults occur in the product, take it out of service and secure against unauthorized use.
Design and function
The IO-Link Wireless Bridge is an IO-Link Wireless Class A bridge with an IP67 housing. It has an internal antenna and two M12 connections for data and power.
The IO-Link Wireless Bridge is based on the IO-Link wireless standard for W-Bridge devices and is part of an IO-Link wireless environment. It communicates with an IO-Link Wireless Master.
The required components are an IO-Link Wireless Master, an IO-Link device (an IO-Link sensor, an IO-Link actuator or an IO-Link hub) and a power cable.BALLUFF BNI IOW-560-W01-K022 - fig Operating and display elementsBALLUFF BNI IOW-560-W01-K022 - fig 1 Pairing button
The pairing button is used to replace an existing IO-Link Wireless Bridge with a new one.
The IO-Link Wireless Bridge must be switched off to ensure that the master disconnects before a new module is installed.
Power-LEDs

Signal Meaning
Green, static Power is on.
Off No voltage

Status LED

Signal Meaning
Magenta No wireless connection
Blue Wireless bridge is ready for use
Green Wired device ready for operation
Yellow Wired device not ready for operation
White Wireless error
Flashing green Firmware update mode

Installation

The IO-Link Wireless Bridge can be mounted with or without a mounting bracket (included in scope of delivery).
Installation with mounting bracket

  1. Secure the mounting bracket to the flange, machine or another surface with M3 screws or cable ties.
  2. Press the IO-Link Wireless Bridge into the mounting bracket.

** The IO-Link Wireless Bridge can simply be pulled out of the mounting bracket to remove it.
Electrical connection
The IO-Link device can be connected to the IO-Link Wireless Bridge directly or via an M12 connector with a cable.
NOTICE
Product damage
The product does not have reverse polarity protection. If the device is connected incorrectly, it may be irreparably damaged.
► Ensure that the polarity is correct.
Power supply Top view of M12 plug, A-coded **

Pin Signal Description
1 L+ +24 V, module supply
2 n/a
3 L− 0 V (GND), module supply
4 n/a
5 n/a

IO-Link

Top view of M12 socket, A-coded

Pin Signal Description
1 L+ +24 V, IO-Link device supply
2 n/a
3 L− 0 V (GND), IO-Link device supply
4 C/Q IO-Link communication
5 n/a

Innovating automation
www.balluff.com

Headquarters| DACH Service Center| Southern Europe Service Center
---|---|---
Germany
Balluff GmbH
Schurwaldstrasse 9
73765 Neuhausen a.d.F.
Phone +49 7158 173-0
Fax +49 7158 5010
balluff@balluff.de| Germany
Balluff GmbH
Schurwaldstrasse 9
73765 Neuhausen a.d.F.
Phone +49 7158 173-370
service.de@balluff.de| Italy
Balluff Automation S.R.L.
Corso Cuneo 15
10078 Venaria Reale (Torino)
Phone +39 0113150711
service.it@balluff.it
Eastern Europe Service Center| Americas Service Center| Asia Pacific Service Center
Poland
Balluff Sp. z o.o.
Ul. Graniczna 21A
54-516 Wrocław
Phone +48 71 382 09 02
service.pl@balluff.pl| USA
Balluff Inc. 8125 Holton Drive
Florence, KY 41042
Toll-free +1 800 543 8390
Fax +1 859 727 4823
service.us@balluff.com| Greater China
Balluff Automation (Shanghai) Co., Ltd.
No. 800 Chengshan Rd, 8F, Building A, Yunding International Commercial Plaza 200125, Pudong, Shanghai
Phone +86 400 820 0016
Fax +86 400 920 2622 service.cn@balluff.com.cn

BALLUFF - logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals