moa EF82B Electric Fireplace Instruction Manual
- June 8, 2024
- moa
Table of Contents
Electric Fireplace EF82B
Instruction Manual
EF82B Electric Fireplace
This product is only suitable for well insulated spaces or occasional use.
BEFORE USE
Before use, please read this manual carefully.
Only connect the appliance to an earthed wall socket.
This appliance is for household use only. When using electrical appliances,
basic safety precautions should always be followed to avoid fires, electric
shocks, burns, or other injuries and damage. Read these operating and safety
instructions carefully.
SAFETY INSTRUCTIONS
– This heater must be used on an AC supply only and the voltage marked on the
heater must correspond to the supply voltage.
– Do not switch the appliance on until it properly installed as described in
this manual.
– The heater must not be located immediately below a socket outlet.
– Do not leave the appliance switched on when leaving your home or going to
sleep.
– Do not leave unattended when plug in to the mains supply.
– This heater is not intended for use by children.Never leave unsupervised
children where the heater is left switched ON (I) or unguarded.
– Only use the appliance for domestic purposes and in the way indicated in
these instructions.
– From time to time check the cord for damages. Never use the appliance if the
cord or any part of the appliance shows any signs of damage.
– If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
– Do not use this heater in the immediate surroundings of a bath, a shower or
a swimming pool.
– Do not cover or obstruct any of the heat outlet grilles or the air intake
openings of the heater.
– Keep the heater clean. Do not allow any objects to enter any ventilation or
exhaust opening as this may cause electric shock, or fire or damage to the
heater.
– Make sure the connection cord does not touch any hot surfaces.
– Keep the appliance at least 100cm (1.0m) from walls and any other
combustible materials.
– Do not use the appliance outdoors
– Do not use if you have wet hands.
– Never move the appliance by pulling the cord.
– Before cleaning the appliance, make sure it is unplugged from the mains
power and that it is completely cool
– Do not clean the appliance with abrasive or chemicals.
– Never use accessories that are not recommended or supplied by the
manufacturer.
– Never route the mains cable beneath carpet.
– Never use aerosols or similar close to the heater.
– Never use the heater to dry clothes or any other similar items.
– In order to avoid a hazard due to inadvertent resetting of the thermal cut
cut-out, this appliance must not be supplied through an external switching
device, such as a timer, or connected to a circuit that is regularly switched
on and off by utility.
– This heater must not be used with an extension lead.
– Do not use this heater with a programmer, timer or any other device that
switches the heater on automatically, since a fire risk exists if the heater
is covered or positioned incorrectly.
– Children should be supervised to ensure that they do not play with the
appliance.
– This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience or knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved.
– Cleaning and user maintenance shall not be made by children without
supervision.
– Children of less than 3 years should be kept away unless continuously
supervised.
– Children aged from 3 years and less than 8 years shall only switch on/of the
appliance provided that it has been placed or installed in its intended normal
operating position and they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved. Children aged from 3 years and less than 8 years shall not plug in,
regulate and clean the appliance or perform user maintenance.
WARNING: This heater is not equipped with a device to control the room
temperature. Do not use this heater in small rooms when they are occupied by
persons not capable of leaving the room on their own, unless constant
supervision is provided.
– There may be trace of odor during the first few minutes of initial use. This
is normal and will quickly disappear.
CAUTION- Some parts of this product can become very hot and cause burns.
Particular attention has to be given where children and vulnerable people are
present.
WARNING! In order to avoid overheating, do not cover the heater.
GETTING STARTED
– Remove the appliance from the box.
– Remove any packaging from the appliance.
– Place the packaging inside the box and either store or dispose of safely.
CONTENTS OF CARTON
– Heater.
– Wall fixing brackets
– Fixing screws and wall plugs.
– Remote control.
-1 Instruction Manual.
HELPFUL ADVICE BEFORE FITTING
– Please retain all packaging until you have checked and counted all the parts
and the contents of the fixing pack against the parts list.
– The fixing pack contains small items which should be kept away from young
children.
– Suggest that you open the fixing pack and place all the contents into a
container, therefore reducing the risk of losing any small pieces.
INSTALLATION INSTRUCTIONS
– Do not connect the heater until properly fixed to the wall and the
instructions is read fully.
– The minimum distances must be observed.
– For installation of the heater, care must be taken not to damage concealed
cables.
– Please be careful while drilling the holes.
– The heater is designed to be permanently fixed to a wall at a minimum height
of 300mm.The wall bracket must be fitted horizontally and the cable routed to
the bottom right of the heater.
– A height of 600mm from the bottom of heater to the floor is recommended for
optimum viewing of fuel bed (see Fig.2 for recommend fixing dimensions)
– Keep top of the heater at least l 000mm away from ceiling or other objects
for optimum heat ventilation.
– For optimum viewing, mark the top five screws fixing positions on wall in
accordance with the recommend fixing dimensions- see Fig.2. Drill holes with a
six drill bit.
– Fix the wall fixing bracket using that the wall plugs and screws provided.
– Carefully lift the heater up ensuring that the two top rear slots of heater
engages the wall fixing bracket (see Fig.3 ) and is sitting centrally.
– Gently bring the heater level with the wall.
– Mark the two bottom holes position-see Fig.5, remove the heater ensuring
that the bottom fixing bracket is rotated up.
– Drill and fit wall plug.
– Refit the heater to the wall fixing bracket and rotate the bottom fixing
bracket down again and use the screws provided to permanently fix the heater
in place.
– Place the front glass panel over the front of the heater aligning the hooks
at each side of the glass panel with the slots at each side of the heater
body-See Fig.4. Then slide down the glass panel in place. Again two people
will be required for this operation.
– Insert and tighten the front glass panel screw-See Fig.6 to secure the front
glass panel to the heater.
OPERATION INSTRUCTIONS
The Controls
-
Switching ON/OFF
– Use the ON/OFF switch to power on the heater (set it to standby mode).
– In standby mode, the heater can be operated either manually by the switches located at the top and right hand side of heater or by the supplied remote control. -
Manual Operation
– NOTE: The heater only starts working if the set temperature is higher than the ambient room temperature.
“O” : Heater powered off
“-“: Heater powered on, set to standby mode
“I/O” : -Press to switch the flame effect ON/OFF
-Press and hold to toggle between 5 different flame dim levels
“power” : -Press once to activate low level heating(1000W)
-Press twice to activate high level heating(2000W)
-Press three to switch off heating
“back light” : Press to toggle between 7 different back light effects
REMOTE OPERATION
NOTE: The heater should be powered on using the ON/OFF switch before it can be operated using remote control.
- Go up in menu (change day)
- Set timer key
- increase tempratur/increase hour/minute
- Go down in menu (change day)
- Cancel key
- Timer on/ off key
- Toggle between 5 different flame dim levels
- Switch the appliance on/ set to standby mode
- Set day/time
- Decrease tempratur/decrease hour/minute
- Confirm selection
- Set automatic heating mode
- Press once to activate low level heating/ Press twice to activate high level heating/ Press three times to switch off heating
- Toggle between 7 different back light effects
– The remote control requires 2xAAA size batteries (Not included)
– Open the battery compartment by sliding the cover down and insert the
batteries noting the polarity indicated in the battery compartment.
– Keep batteries out of reach of children.
– Remote control operations are identical to the functions on the control
panel.
– The remote control must be point directly at the sensor on control pad.
DISPLAY
1. Timer icon
2. Day of the week
3. Temprature/timer number
4. Timer off
5. Timer on| 6. Flame dim level
7. Time/temprature display
8. Standby mode icon
9. Automatic heating mode
10. Heating level 1 star= low heating level, 2 star = high heating level.
---|---
SETTINGS
-
Setting weekday and time
– Press the DATE/TIME key. When the day is flashing press the up or down key to select the day.
– Press the DATE/TIME key again, then press the + or — key to set the hour.
– Press the DATE/TIME key again, then press the + or — key to set the minute.
– Press the OK key to confirm the setting. -
Setting temperature
– NOTE: This setting is only applicable for the temperature in standard heating mode, not for the temperature in the timer mode. The default set temperature is 20 °C.
– NOTE: The heater only starts working when the set temperature is higher than the room temperature.
– Press the + or — key to set the temperature, which ranges from 15 to 30 °C.
– After the temperature setting has been completed, the display flashes about 5 seconds, then shows the room temperature. -
Setting timer
– Up to 10 different timer settings can be programmed.
– Each timer setting has its day, power-on time and power-off time.
– The maximum duration of each timer setting is 23 hours 50 minutes.
– If the power-off time of the timer setting falls on the following day, it is unnecessary to set the day-lust set the power-off time.
– Press the TIMER SET key, the timer number starts blinking (01-10).
– Press the + or — key to select a timer number.
– Press the TIMER SET key, the cursor on the left side of the day blinks.
– Press the up or down key to move the cursor to the corresponding day. Press the + key to add a corresponding day, or press the – key to delete a day.
– Press the TIMER SET key to set the on time. The hour digit starts blinking.
– Press the + or — key to set the hour. – Press the TIMER SET key. The minute digit starts blinking.
– Press the + or — key to set the minute. – Press the TIMER SET key to set the off time. The hour digit starts blinking.
– Press the + or — key to set the hour. – Press the TIMER SET key. The minute digit starts blinking.
– Press the + or — key to set the minute.
– Press the TIMER SET key. The temperature digit starts blinking.
– Press the + or — key to set the temperature.
– Press the TIMER SET key to continue with the timer setting or press the OK key to confirm the selling. -
Viewing the timer setting
– Press the TIMER SET key.
– Press the + or — key to check the power-on time of the set timers one by one.
– To check the power-off time, press the up key.
– Press the + or — key to check the power-off time of the set timers one by one.
– To delete selected setting, press the C key. -
Activation timer
– Press the TIMER ON/OFF key to activate the timer function.
– NOTE: When the timer is active, the heating level must be manually selected. If the heater function is not selected; only the flame effect goes on at the set power-on time. -
Automatic heating mode
– Press the IC key to activate automatic heating mode. The AUTO icon appears on the display.
– When the automatic heating is turned on, the heater automatically changes the heating level depending on the set temperature and the ambient room temperature.
MAINTENANCE
– WARNING: Before any maintenance and/or cleaning the exterior of the
heater, disconnect the heater form the power supply and leave heater cooled
off.
– The heater uses an electronically controlled LED system to create the flame
effect therefore no parts need to be replaced. Under no circumstances should
the heater be serviced by anyone other than a qualified electrician.
SAFETY CUT-OUT
– This heater is fitted with a safety cut-out which will operate if the heater
overheats (e.g. Due to blocked air vents). For safety reasons, the heater will
NOT automatically reset.To reset the heater, disconnect the heater from the
mains supply for at least 15 minutes. Reconnect the supply to the mains and
switch on the heater.
CARE AND CLEANING
– Always disconnect the heater from mains supply and allow cooling before any
cleaning operation.
– Trim parts may be cleaned using a clean, damp cloth. Never use abrasive
cleaners and chemical agents as damage may occur to the finish.
DISPOSAL
Do not dispose of the device in normal domestic waste. Dispose of the device
over a registered waste disposal firm or through your communal waste disposal
facility.
Observe the currently valid regulations. In case of doubt, consult your waste
disposal facility.
WARRANTY
Dear Valued Customer, Thank you very much for purchasing a MOA product. We
wish you to inform you that this product is covered by a warranty which
complies with all legal provisions concerning existing warranty and consumer
rights in the country where the product was purchased. Should you find any
defect or malfunction of your MOA product, please contact the appropriate
Customer Care Center.
Sincerely yours,
The MOA Team
APPLIANCE DATA
| Item | Symbol | Value | Unit |
|---|
Heat output
Nominal heat output| Pnom| 2| KW
Minimal heat output| Pmin| 1| KW
Maximum continious heat output| Pmax, c| 2| KW
Auxiliary electricity consumption
At nominal heat output| ELmax| 0.014
(Fan heater)| KW
At minimum heat output| ELmin| 0.014
(Fan heater)| KW
In standby mode| ELsb| 0.48| KW
Type of heat input, for electric storage local space heaters only (select
one)
Manual heat charge control, with integrated thermostat – Not applicable Manual
heat charge control with room and/or outdoor temperature feedback – Not
applicable electronic heat charge control with room and/or outdoor temperature
feedback – Not applicable
Fan assisted heat output – Not applicable
Type of heat output/room temperature control (select one)
Single stage heat output and no room temperature control – No
Two or more manual stages, no room temperature control – No
With mechanic thermostat room temperature control – No
With electronic room temperature control – No
Electronic room temperature control plus day timer – No
Electronic room temperature control plus week timer – Yes
Other control options (multiple selections possible)
Room temperature control, with presence detection – No
Room temperature control, with open window detection – No
With distance control option – No
With adaptive start control – Yes
With working time limitation – No
With black bulb sensor – No
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>