baby trend WK14 F Series Trend 4.0 Activity Walker Instruction Manual

: June 8, 2024
: baby trend

Table of Contents

WARNING
- BATTERY WARNING
PARTS
- ASSEMBLY
OPERATION
FCC Statement
BABY TREND® CUSTOMER SERVICE
WARRANTY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

baby trend WK14 F Series Trend 4.0 Activity Walker

Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE

WARNING

: Please read all instructions before assembly and use of the walker. Keep instructions for future use.
: Never leave child unattended. Always keep child in view while in walker.
: Use only on flat surfaces free of objects that could cause the walker to tip over.
: To reduce chance of child slipping out of the seat, check that both feet of the child touch the floor. Never carry walker with the child in it, as the child may get hurt or slip out.
: To avoid burns, keep the child away from hot liquids, ranges, radiators, space heaters, fireplaces, etc.
-STAIR HAZARD: Avoid serious injury or death, block stairs/steps securely before using walker.

This walker is to be used only by infants, who are old enough to sit upright on their own and are ready to learn to walk (about 6 months old). DO NOT USE UNTIL BABY CAN SIT UP BY ITSELF.
Discontinue using the walker if your child attempts to climb out, reaches 30 pounds in weight or 32 inches in height, or when your child is able to walk unassisted.
DO NOT ADJUST TRAY HEIGHT WITH THE BABY IN THE WALKER.
Periodically inspect seat pad plastic tabs to be sure they are secured in the body.
DO NOT USE THE WALKER IF IT IS DAMAGED OR BROKEN.
Discontinue use should any part become damaged. Please contact our customer service at 1-800-328-7363 to order replacement parts or arrange for repairs.
Clean the stoppers on walker base regularly to maintain stopping performance. To clean the seat pad, use only mild household soap and warm water with a sponge or cloth.
DO NOT MACHINE WASH. For metal and plastic parts, use only lukewarm water and mild soap.

BATTERY WARNING

Requires two “AA”(LR6) alkaline batteries (not included) for toy operation.
Non-rechargeable batteries are not to be recharged.
Different types of batteries or new and used batteries are not to be mixed.
Batteries are to be inserted with the correct polarity.
Exhausted batteries are to be removed from the toy.
The supply terminals are not to be short-circuited.
Rechargeable batteries are to be removed from the toy before being charged.
Rechargeable batteries are only to be charged under adult supervision

PARTS

Base
Seat
Wheels
Toy bar
Toy Tray
Push Handle
Rattle and (1) Connector
Butterfly toy and (1) Connector
Music Unit
Stoppers (6 pcs)

IMPORTANT! To ensure safe operation of your product, please follow these instructions carefully. Please keep these instructions for future reference.
IMPORTANT! Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. NEVER use if any parts are missing or broken.
IMPORTANT! Adult assembly is required.
IMPORTANT! Always check that the baby walker is locked in the open position before using.
ATTENTION: Carefully remove parts from box. Check that you have all the parts for this model before assembling the baby walker

ASSEMBLY

TO ASSEMBLE WALKER PARA ENSAMBLAR EL ANDADOR

1) To open the baby walker raise the tray to the middle position (Fig. 1).
The baby walker can be used for 3 different heights. Turn the safety button and slide vertically to adjust the height. See the 3 heights diagram under the walker for indications of the height being used ( **Fig. 2).

**

Check that the safety button is turned 90 degrees to prevent the accidental release of the mechanism **(Fig. 3).

**

Attach the fabric nearest to the tray, push the pin downward through the fabric into to the hole of the frame until it snaps into place. Repeat for the opposite side (Fig. 4a).
Insert the pins on the back of the seat, into the holes by pushing downwards through the fabric until each one clicks (Fig. 4b).
Lastly, insert the pins into the holes behind the tray, by pushing downwards through the fabric until each one clicks (Fig. 4c).

NOTE: All pins should be aligned to the corresponding holes of the frame and click into place to ensure the fabric is securely attached
Insert the Push Handle into the frame. Push in firmly until it clicks into position. NOTE: Do Not lift the walker from the Push Handle (Fig. 4d).
lace walker on a solid flat surface with bottom of base facing upward. Insert the pins of the wheels into their housing by pressing them until they snap into position **(Fig. 5a).

**

Insert the pins of the 6 stoppers and 2 rear wheels into their housing by pressing them until they snap into position (Fig.5b).

Ensure to apply enough pressure when inserting the stoppers so that they push in lower than the level of all the wheels (Fig.5c).

Please check that wheels are locked into place before proceeding.
TOY TRAY ASSEMBLY MONTAJE DE BANDEJA PARA JUGUETES

6) • Ensure the strap is tucked underneath the music unit. Insert the music unit into the center of the toy tray until it snaps in securely (Fig. 6a).

NOTE: To install or replace batteries, refer to page 12.
• (1) Insert the toy bar on the front of the tray. (2) Then place the two connectors onto the toy tray and twist until it snaps in securely (Fig. 6b).

• Align the rattle and butterfly toys to their corresponding slots on each connector (Fig. 6c).
7) Remove the music unit by pressing the tab, then slide it out to remove (Fig. 7a).
To install or replace batteries, remove the strap and open the battery door by using a screw driver **(Fig. 7b).

**

The toy requires 2 double AA batteries. Install batteries as shown (Fig. 7c).

NOTE: Close the battery door and secure it by using the screw driver. Then place the strap back into place.
8) After aligning the toy tray into the tray knobs of the walker, ensure both knobs are turned completely to securely lock it into the tray (Fig. 8a).

Do not use the toy tray if it has been damaged or broken.
• To remove the toy tray: Underneath the walker tray, twist both knobs in order to remove the toy tray (Fig. 8b).

TO REMOVE TOYS CÓMO QUITAR JUGUETES
1. To detach the toys: Twist the two connectors on the tray to remove the two toys (Fig. 9a).
To disconnect the individual toys, squeeze the tabs underneath the connector to release. Repeat the same process for the rattle (Fig. 9b).
Remove the music unit by pressing the tab, then slide it out to remove (Fig. 9c).
Flip the toy tray over and squeeze the two tabs to remove the toy bar on each side (Fig. 9d).
10) Optional: Hang the music unit onto the push handle when not in use and adjust the strap if needed (Fig. 10).

Reverse the step above to remove the music unit from the push handle.
TO FOLD WALKER PARA PLEGAR EL ANDADOR
1. • To fold the walker, turn the button to unlock and push it to release. Then push the tray downward to the lowest position (Fig. 11).
  
  TO REMOVE SEAT PARA RETIRAR EL ASIENTO
12) Lift the front plastic pins of the seat upwards and pull the pins out of the ho les (Fig. 12a).
• Squeeze and release the straps with plastic buckles on back of seat from their corresponding slots underneath the tray (Fig. 12b).

PLACING CHILD IN THE WALKER
: To reduce chance of child slipping out of the seat, check that both feet of the child touch the floor. Never carry walker with the child in it, as the child may get hurt of slip out.
Always check the walker prior to each use to ensure that the seat is snapped in place and that the walker has no loose or broken parts.
Do Not use the walker if it is damaged or broken or missing parts.

OPERATION

Adjust the seat height of the walker to the lowest setting. Place your child in the walker and check that both feet touch the floor. The child should have only part of their weight on their feet when their legs are straight. Adjust the walker height as needed as your child grows. Do not adjust height with child in the walker. Discontinue using the walker if your child attempts to climb out, reaches 30 pounds in weight or 32 inches in height, or when your child is able to walk unassisted.

FCC Statement

The FCC Statement applies only to electronic units This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1 this device may not cause harmful interference, and 2 this device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

BABY TREND® CUSTOMER SERVICE

The Customer Service Department can be contacted at 1 800-328-7363 Monday through Friday between 8:00 a.m. and 4:30 p.m. (PST). Return Authorizations are required prior to returning product(s) to Baby Trend®.

WARRANTY

DO NOT RETURN YOUR PRODUCT TO THE STORE. PLEASE CONTACT BABY TREND® FOR REPLACEMENT PARTS, SERVICE AND REPAIR.
The Baby Trend® warranty covers workmanship defects within 1 year of purchase. Any product which has been subjected to misuse, abuse, abnormal use, excessive wear and tear, improper assembly, negligence, environmental exposure, alteration or accident, or has had its serial number altered or removed invalidates all claims against the manufacturer. Any damage to property during installation is the sole responsibility of the end user. Customer Service Department can be contacted at 1 800-328-7363 Monday through Friday between 8:00 a.m. and 4:30 p.m. (PST). Return Authorizations are required prior to returning product(s) to Baby Trend®. Please visit http://babytrend.com/pages/limited-warranty for complete warranty details.