WOODBRIDGE WN-990 Smart Bidet User Manual
- June 8, 2024
- WOODBRIDGE
Table of Contents
WOODBRIDGE WN-990 Smart Bidet User Manual
Thank you for acquiring this innovative, useful and reliable smart appliance.
You will soon be reassured that your
decision to use this product was well-made.
CAUTION
Before unpacking this bidet, please check, once again, that the size is the
right size for your toilet. The carton box
has the size marked on it – using the letter “S” or “L”.
NOTE:
T he pictures in this manual are only representative drawings. They may be
similar to the product but not identical.
Design and other changes including continuous product improvements, which do
not materially impact the user
manual, may not be illustrated herein.
The unit was manufactured for household use
- This product should be installed according to this manual.
- Please read this manual carefully and install properly.
- Please keep this manual for future reference.
- Please register Warranty for proper service.
SAFETY INSTRUCTIONS
The following sticker is placed on to the toilet seat cover, visible when the cover is in the open position, to serve as a constant reminder of some important do’s and don’ts:
ATTENTION
FEATURES
SAFETY INSTRUCTIONS
Please also note the following:
- Connect the bidet to a standard 3-pin earthed socket for electricity supply.
- Avoid touching the plug or socket with wet hands.
- Connect the Power Cord only after installation has been fully completed.
- Remove the plug from the socket whenever repairing or dismantling the bidet.
- Avoid connecting many plugs to the same socket outlet.
- If the socket and/or the plug are damaged, contact an electrician for replacement.
- Connect the appliance to a potable water source that is intended for household use.
- If the water supply in your house contains limestone, or other impurities, connect the water filter that is supplied in the accessories. This filter will need to be replaced periodically depending on the water quality in your home. The filter is not covered by our warranty.
- Should the bidet develop any defect, stop using it and contact the service centre immediately.
- Do not apply excessive force when pushing the buttons on the control panel.
- Do not urinate directly on the nozzle.
- Do not block the deodorizer air outlet vents.
- Do not lean back against the lid, during use, as this may damage it.
- Do not expose this product to direct sunlight, as it may cause the plastic parts to discolour.
NB: THE NON-RESPECT OF THESE SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS DAMAGE TO THE APPLIANCE AND/OR INJURY TO THE USER.
PARTS & ACCESSORIES
INSTALLATION
CAUTION
While this bidet is easy to install, you are strongly advised to use a
qualified professional for a hitch-free installation and subsequent
utilization.
DO NOT CONNECT TO A POWER SOURCE UNTIL THE INSTALLATION HAS BEEN COMPLETED.
USING THE BIDET
SITTING ON THE TOILET SEAT
When seated, the Occupied Sensor indicator lights up on the rear Indicator Panel and, at the same time, you can hear a short beep.
The Deodorization function also starts up automatically and will keep working
until 1 minute after you stand up.
For the first use, set the water temperature, and water pressure, to the
lowest positions as explained below. After using any wash function, you will
be able to set the temperature, to your preferred level, for future use. The
water pressure can be adjusted at any time whereas the water temperature
increase, or decrease, takes a very short time to be attained.
WASH CONTROLS:
REAR WASH
This button starts the water spray for the usual cleaning of the anal zone.
The water is mixed with a little air which creates a soft feel. At this time,
it is advisable to set all parameters for your comfort (nozzle position, water
temperature and water pressure). You should then press the Oscillate button so
that the back and forth movement, of the nozzle, will result in a larger area
being cleaned. The Massage function is also useful during this rear wash –
either on its own or along with the Oscillate function.
LADIES’ WASH
This button starts a gentle and lukewarm spray onto the feminine zone. The
temperature and pressure can be adjusted to comfortable levels. The Oscillate
and the Massage functions are also useable and useful for this type of wash.
CATHARSIS WASH (Deep Clean)
This function is to assist in evacuating residual faeces from the rectum.
First set the water pressure on low and then press the Catharsis button. A
focused spray is directed at the anus. Adjust your seated position, and the
water pressure, to ensure that the jet of water can penetrate through the anus
without any water splashing, pain or discomfort. As soon as you feel that the
rectum is getting full, press the stop button. The water softens the faeces
thereby enabling it to be released more easily.
STOP BUTTON
All above wash and dry functions will stop as soon as this button is pressed.
MASSAGE
Pressing this button during the WASH functions creates a massaging effect by alternating the spray strength between high and low.
The water massage pulsation strength can be adjusted by using the High and Low
buttons. The water pressure
will return to the starting mode if you press the Massage button once again.
OSCILLATE
By pressing this button, the nozzle will shuttle back and forth 12mm, thereby
enlarging the cleaning area in the
REAR and LADIES’ WASH functions.
You can adjust the oscillating scope by pressing the arrow buttons (←or ) .
The nozzle will stop moving if you press the Oscillate button once again when
it is moving.
DRY
By pressing this button, gusts of warm air will come out to dry wet part(s). You can adjust the air temperature by pressing the High and Low buttons.
WATER PRESSURE
Generally, you can control the water pressure by pressing the High and Low buttons – of course, when you are seated on the toilet seat. However, if you wish for the level to be memorised, press the Massage button for 3 seconds and it will set the pressure at the lowest level. If you press the Massage button again for another 3 seconds, the water pressure level will be memorised at the medium level. Pressing the Massage button yet again for 3 seconds, the pressure returns to the lowest level.
You will notice the appropriate pressure level indicator, on the control panel, lights up during each of the above steps.
NOZZLE POSITION
The nozzle moves forward & backward along a length of 12mm. The arrow buttons
( ←or→ ) enable you to select from a choice of 5 different nozzle positions to
suit your convenience.
WATER TEMPERATURE
At the starting stage, the temperature is in the off position. Therefore, the
temperature of the water, in the bidet’s
own tank, would be either the room temperature or that of the water supply.
By pressing the WATER Temperature button, the Temperature indicator’s green light comes on and the water temperature rises to 34°C/93 2 . By pressing the button again, the yellow light comes on and the temperature stabilises at 37°C/98.6℉. Pressing the button, once again, makes the red light come on and the temperature climb to 40°C/104℉. The same cycle is repeated with every press of the button.
SEAT TEMPERATURE
By pressing the SEAT Temperature button, the Temperature indicator’s green
light comes on and the seat temperature will rise to 34°C/93.2℉. By pressing
this button again, the yellow light comes on and the temperature will climb to
38°C/100.4℉. Pressing the button, once again, makes the red ligh come on and
the temperature will be at 41°C/105.8℉. The same cycle is repeated with every
press of the button.
POWER SAVER
When you press the Power Saver button, the Power Saving 1 indicator lights up
on the rear Indicator Panel. In this function, the power saving is significant
since the water heating will stop and will restart after 8 hours. Pressing the
button a 2nd time, starts the Power Saving 2 function. This is an “Eco Mode”
with constant low power consumption. Here,the water and seat temperature are
kept at about 32℃/89.6℉. If you press the button a 3rd time, the Power Saver
function gets switched off.
If the Power Saving function is in use, it will temporarily stop when someone
sits on the bidet.
The function will resume as soon as the user stands up.
DEODORISER
This device is useful in eliminating odours from the toilet bowl area. It has
a motor which expels air (and odour), from that area, and deodorises it as it
passes out of the vents on the side of the bidet.
This deodoriser function starts automatically as soon as the user sits on the toilet seat. It will continue to work for 1 minute after the user stands up. (Please see page 8 for further information.)
MAINTENANCE
NOZZLE
Firstly, ensure that there is no object on the seat’s Seat Occupied Sensor and that you are also not seated on the bidet. Press the Rear Wash button for 3 seconds and the Nozzle will stretch out. Use a toothbrush to clean any dirt or stains that may have settled on the nozzle.
Press the Rear Wash button again to return the nozzle to its normal covered position.
DEODORISER
If you notice a drop in the performance of the deodoriser, pull out the deodorising cartridge, as shown, and, using a soft toothbrush, gently brush off any dust or dirt that may have collected on the cartridge. After about 6 months of routine cleaning, if you feel it is no longer working, remove the cartridge and expose it to direct sunlight for 2 to 3 hours. This should reactivate the carbon and allow further use. At some stage, After many years of average bidet use, you may have to replace it due to it having reached its natural expiry.
SPECIFICATIONS
TROUBLESHOOTING
DISMANTLING THE BIDET
If you need to remove the bidet for cleaning purpose, or for sending to the service centre, please:
- Remove the plug from the power socket and
- Cut off the water supply by turning the valve clockwise. Disconnect the hose from the bidet.
- Press the button on the side of the bidet, as shown, to completely empty out the water tank.
- Press again the side button and slide out the bidet by pulling it towards you as shown.
The button on the right side of the seat is to be used for draining out the water and also for unlocking the bidet from the mounting plate.
NOTE: If you are removing the bidet to install it elsewhere, then continue with the following steps:
5. Remove the T-valve, the water filter and the hose that connects the filter
to the bidet. Empty out the water from the filter and hose.
6. Re-fix the original water inlet hose from the valve directly to the water
tank (cistern) of the toilet. Turn on the water supply by turning the valve
anti-clockwise.
CAUTION: Do not use excessive force when tightening the nuts of the hose with your spanner.
WARRANTY CARD
SMART BIDET
Model No:
Serial No:
Date of Purchase:
TERMS AND CONDITIONS
Please send a copy of the completed form, to the nearest service centre, retaining the original with you.This is to avoid any unnecessary difficulties regarding the eligibility of warranty.
For availing service under this limited warranty, the service centre will advise you if the repair/ service will be carried out at your premises or the product needs to be brought to the service centre. You need to produce this form along with original purchase invoice.
This purchase is warranted against defects in material and workmanship for a period of 1 year from the date of first purchase from an authorized dealer, subject to correct installation and use. This warranty is not valid in the event of a resale and the rights hereunder are not assignable. During the warranty period, the Company’s service centre will provide, free of charge, labour service and replacement of only those materials with ex-factory defects. While the Company will make best efforts to repair as early as possible, it is expressly stated here that no time period is set for such a repair.
This warranty will not apply to any failure of the product due to improper maintenance, misuse, abuse, repairs/ maintenance by unauthorised agency, tampering, etc. Damage to, and alteration/ removal of, the serial number will result in the warranty being null and void.
This warranty is not applicable to any damage due to fire, natural disasters, acts of war and public disturbances.
Dealer’s Details
Name
Address:
Signature & Stamp:
Customer’s Details
Name
Address:
Tel. No.:
Signature:
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>