Leader Premiums AE0213 Terrazzo 5W Bluetooth Speaker User Manual
- June 4, 2024
- Leader Premiums
Table of Contents
Leader Premiums AE0213 Terrazzo 5W Bluetooth Speaker
Product Overview
- Power button: Press and hold for 3 seconds, turn on/off the speaker, short press to play/pause music
- Up button: short press to select the previous track
- Volume + button: short press to increase the volume
- Volume – button: short press to decrease volume
- Down button: short press to select the next music track
Package Contents
- 1 x Terrazzo speaker
- 1 x Charging cable
- 1 x User manual
Specifications
- Bluetooth version: BT 5.0
- Rated output power: 5W
- Impedance: 4 Ω
- Signal noise ratio: 80dB
- Input: 5V/500mA
- Charging time: 2 hours
- Speaker driver size: φ52mm
- Range: 10 m
- Frequency response: 50Hz-15KHz
- Battery: 3.7V/500mAh
- Playback time: up to 2 hours at max. volume
Instructions
- Press and hold the power button (1) for 3 seconds to turn on the speaker.A voice prompt “Powered
- ON, Pairing ” and LED flashing blue will indicate Bluetooth pairing mode has been entered.
- Open your Bluetooth options on mobile, activate Bluetooth and select the pairing name ‘Terrazzo BT speaker’.
- After successful connection, a tone will prompt “Connected” and the LED turning solid Blue indicates
- Bluetooth is connected. LED will flash blue when playing music.
- Disconnecting Bluetooth will prompt a voice “Disconnected”. When Bluetooth is disconnected, the speaker will automatically shut off after 5 minutes.
- Press and hold the power button (1) for 3 seconds to turn off the speaker and hear a voice prompt “Powered OFF”.
- Short press the power button (1) to play/pause music.
- Short press the power button (1) to answer an incoming call. Press and hold the power button (1) for 2 seconds to reject the incoming call.
- Short press the Up button (2) to resume the previous track.
- Short press the Down button (5) to switch to the next track.
- Short press the Volume +/- button (3&4) to adjust the volume.
Charging
-
Use the charging cable provided to connect to an adaptor or computer to charge the speaker.
-
LED will turn solid RED when charging and LED will turn off when fully charged. It will take approximately 2 hours to charge the speaker from 0% to 100%.
Troubleshooting
Safety Precautions
WARNING – When using this product, basic precautions should always be followed, including the following: Read the instructions fully before using the product.
- The unit will only achieve full performance after 2 or 3 completed charge and discharge cycles.
- Do not overcharge your case. The unit may become hot under excessive use. Remove your case once it is fully charged.
- To reduce the risk of injury, close supervision is required when the product is used near children.
- Do not expose the device to moisture.
- Do not use the device in excess of its output rating.
- Overloaded outputs above the rating may result in a risk of fire or injury.
- Do not use the device if damaged or modified.
- Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
- Do not disassemble the device. Take the device to a qualified technician if service or repair is required. Incorrect reassembly may result in a risk of fire or injury.
- Do not expose the device to fire or temperatures above 212°F/100°C, which may cause an explosion.
- Have servicing performed by a qualified repair technician using only identical replacement parts.
- This will ensure that the safety of the product is maintained.
IMPORTED BY:
PF Concept International Coöperatief U.A.
Kabelweg 1
2371 DX Roelofarendsveen
The Netherlands
www.pfconcept.com
Made in China
IMPORTED INTO THE UK BY:
PF Concept UK
Neptune House, Sycamore Trading Est
Squires Gate La, Blackpool, FY4 3RL
United Kingdom
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the device and receiver.
- Connect the device into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>