SIGNATURE HARDWARE EDISTO 479850 Pendant Instruction Manual
- June 8, 2024
- Signature Hardware
Table of Contents
SIGNATURE HARDWARE EDISTO 479850 Pendant
BEFORE YOU BEGIN
- We recommend consulting a professional if you are unfamiliar with installing electric fixtures. Signature
- Hardware accepts no liability for any damage to the faucet, plumbing, sink, counter top, or for personal injury during installation.
- Observe all local plumbing and building codes.
- Unpack and inspect the product for shipping damage.
- If any damage is found, contact our Customer
- Relations team via live chat at www.signaturehardware.com or by emailing support@siganturehardware.com.
GETTING STARTED
Ensure that you have gathered all the required materials that are needed for the installation.
ADDITIONAL QUESTIONS?
Still need help? Check out our Help Center at www.signaturehardware.com for product and warranty information, or contact us through live chat or by emailing support@signaturehardware.com.
FOR YOUR SAFETY
WARNING: Be sure the electricity to the wires you are working on is shut off, either the fuse is removed or the circuit breaker is shut off. You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system. Read instructions carefully. If you are unclear as to how to proceed, consult a qualified electrician.
CARE INSTRUCTIONS
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
TOOLS AND MATERIALS
INSTALLATION
Carefully push fixture wires up through bottom of loop (M). Pull fixture wires out of top of loop (M). Pull fixture wires taut. Screw loop (M) onto top of fixture body (O).
-
- Attach one locking link (G) onto loop (M).
-
Determine desired hanging height of fixture. Cut chain (H) to length to achieve desired height.
-
Attach chain link at end of chain (H) onto locking link (G) on loop on top of center stem (M).
-
Weave fixture wires through chain (H), skipping every other chain link.
-
Slip threaded ring (F) down over end of chain (H) and fixture wires.
-
Slip hole in canopy (D) over end of chain (H) and fixture wires.
-
Carefully pull house wires down out of junction box so house wires are easily accessible to connect fixture wires.
-
Position mounting bracket (A) so longest end of threaded pipe (W) attached to mounting bracket (A) is pointing down towards floor.
-
Align holes in mounting bracket (A) with holes in junction box.
-
Thread each junction box screw (B) into appropriate holes in mounting bracket (A) and into holes in junction box. Tighten junction box screws (B) to secure mounting bracket (A) to junction box.
-
Thread screw collar loop (E) onto threaded pipe (W). Tighten screw collar loop (E) up against first hexnut on threaded pipe (W).
-
Strip 3/4” of insulation from ends of fixture wires.
-
Push fixture wires up through hole in screw collar loop (E) attached to mounting bracket (A) and out end of threaded pipe inside junction box. Carefully pull fixture wires so they are easily accessible to connect to house wires.
-
To aid in connecting fixture wires to house wires, temporarily connect second locking link (G) to link at end of chain (H) and to screw collar loop (E).
-
Twist the end of fixture white wire to the end of house white wire together. Twist a wire nut onto ends of wires. Wrap electrical tape around wire nut and wires to secure connection. Twist the end of fixture black wire and the end of house black wire together. Twist a wire nut onto the ends of wires. Wrap electrical tape around wire nut and wires to secure connection. Loosen ground screw on mounting bracket (A). Wrap house ground wire around ground screw leaving enough ground wire to attach to fixture ground wire. Twist the end of fixture ground wire to the end of house ground wire together. Twist a wire nut onto ends of wires. Wrap electrical tape around wire nut and wires to secure connection.
Note: If you have electrical questions consult your local electrical code for approved grounding methods. -
After wires are connected, carefully tuck wires inside junction box.
-
Remove second locking link (G) from last link on chain (H) and screw collar loop (E).
-
Raise canopy (D) up to ceiling. Pass hole in canopy (D) over screw collar loop (E). Position canopy (D) up against ceiling.
-
Raise threaded ring (F) up to canopy (D). Screw threaded ring (F) onto screw collar loop (E). Tighten threaded ring (F) to secure fixture to ceiling.
-
Attach second locking link (G) to link at end of chain (H). Attach locking link (G) at end of chain (H) to loop on screw collar loop (E).
-
Screw recommended bulbs (E12 Candelabra bulb type, not included) into sockets. Verify correct bulb wattage marked on socket of fixture.
WARNING: DO NOT exceed maximum bulb wattage.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>