Signature Hardware 479843 Korbel Matte White Modern/Contemporary Dome Pendant Light Instruction Manual
- June 8, 2024
- Signature Hardware
Table of Contents
Signature Hardware 479843 Korbel Matte White Modern/Contemporary Dome
Pendant Light
BEFORE YOU BEGIN
We recommend consulting a professional if you are unfamiliar with installing
electric fixtures. Signature Hardware accepts no liability for any damage to
the faucet, plumbing, sink, counter top, or for personal injury during
installation.
Observe all local plumbing and building codes. Unpack and inspect the product
for shipping damage. If any damage is found, contact our Customer Relations
team via live chat at www.signaturehard-ware.com or by emailing support@siganturehard-ware.com.
GETTING STARTED
Ensure that you have gathered all the required materials that are needed for the installation.
FOR YOUR SAFETY
WARNING: Be sure the electricity to the wires you are working on is shut off, either the fuse is removed or the circuit breaker is shut off. You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system. Read instructions carefully, if you are unclear as to how to proceed, consult a qualified electrician.
CARE INSTRUCTIONS
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
FOR YOUR SAFETY
WARNING: Be sure the electricity to the wires you are working on is shut off, either the fuse is removed or the circuit breaker is shut off. You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system. Read instructions carefully. If you are unclear as to how to proceed, consult a qualified electrician.
TOOLS AND MATERIALS:
SAVE THIS MANUAL: RETAIN FOR CONSUMER’S USE.
READ THESE INSTRUCTIONS COMPLETELY BEFORE INSTALLING THE PRODUCT: FOR PRODUCT
OR INSTALLATION QUESTIONS PLEASE CALL CUSTOMER SERVICE AT
1-800-221-3379.
INSTALLATION
-
Carefully push fixture wires up through bottom of center stem (P). Pull fixture wires out of top of center stem (P). Pull fixture wires taut. Screw bottom of center stem (P) onto top of fixture body (O).
-
Determine desired hanging height of fixture. Select the quantity of stems (M) to achieve that height.
-
Carefully push fixture wires from top of fixture body (O) up through bottom of stem (M). Pull fixture wires out of top of stem (M). Pull wires taut.
-
Carefully push fixture wires through remaining stems (M). Thread stems (M) together carefully keeping fixture wires taut.
-
From last stem (M), push fixture wires up through swivel (S) attached to canopy (D). Carefully pull fixture wires up through canopy (D). Keep fixture wires pulled taut.
-
Screw last stem (M) onto swivel (S) on canopy (D). INSTALLATION (FIG 2)
-
Carefully pull house wires down out of junction box so house wires are easily accessible to connect fixture wires.
-
Position mounting bracket (A) so threaded ends of attached fixture mounting screws (E) are facing down towards floor.
-
Carefully pull house wires through center hole in mounting bracket (A).
-
Thread each junction box screw (B) into each slot in mounting bracket (A) and into holes in junction box.
-
Tighten junction box screws (B) to secure mounting bracket (A) to junction box.
-
Strip 3/4” of insulation from ends of fixture wires.
-
Twist the end of fixture white wire to the end of house white wire together. Twist a wire nut onto ends of wires. Wrap electrical tape around wire nut and wires to secure connection. Twist the end of fixture black wire and the end of house black wire together. Twist a wire nut onto the ends of wires. Wrap electrical tape around wire nut and wires to secure connection. Loosen ground screw on mounting bracket (A). Wrap house ground wire around ground screw leaving enough ground wire to attach to fixture ground wire. Twist the end of fixture ground wire to the end of house ground wire together. Twist a wire nut onto ends of wires. Wrap electrical tape around wire nut and wires to secure connection.
Note: If you have electrical questions consult your local electrical code for approved grounding methods. -
After wires are connected, carefully tuck wires inside junction box.
INSTALLATION (FIG 4)
-
Screw one threaded cap (F) onto each fixture mounting screw (E). Tighten threaded caps (F) to secure fixture to ceiling. DO NOT over tighten.
-
Screw recommended bulbs (E26 Edison bulb type, not included) into sockets. Verify correct bulb wattage marked on socket of fixture.
WARNING: DO NOT exceed maximum bulb wattage.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>