Signature Hardware 479806 Grinnell Vanity Light Instruction Manual

: June 8, 2024
: Signature Hardware

Table of Contents

BEFORE YOU BEGIN
GETTING STARTED
FOR YOUR SAFETY
CARE INSTRUCTIONS
TOOLS AND MATERIALS:
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

479806 Grinnell Vanity Light
Instruction Manual

BEFORE YOU BEGIN

We recommend consulting a professional if you are unfamiliar with installing electric ﬁxtures. Signature Hardware accepts no liability for any damage to the faucet, plumbing, sink, counter top, or for personal injury during installation. Observe all local plumbing and building codes. Unpack and inspect the product for shipping damage.
If any damage is found, contact our Customer Relations team via live chat at www.signaturehardware.com. or by emailing support@siganturehardware.com

GETTING STARTED

Ensure that you have gathered all the required materials that are needed for the installation.

ADDITIONAL QUESTIONS?
Still need help? Check out our Help Center at www.signaturehardware.com for product and warranty information, or contact us through live chat or by emailing support@signaturehardware.com.

Signature Hardware 479806 Grinnell Vanity Light

FOR YOUR SAFETY

WARNING: Be sure the electricity to the wires you are working on is shut oﬀ, either the fuse is removed or the circuit breaker is shut oﬀ. You don’t need special tools to install this ﬁxture. Be sure to follow the steps in the order given. Under no circumstances should a ﬁxture be hung on house electrical wires, nor should a swag type ﬁxture be installed on a ceiling which contains a radiant type heating system. Read instructions carefully. If you are unclear as to how to proceed, consult a qualiﬁed electrician.

CARE INSTRUCTIONS

To clean, wipe ﬁxture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

TOOLS AND MATERIALS:

Signature Hardware 479806 Grinnell Vanity Light - Fig
1

Signature Hardware 479806 Grinnell Vanity Light - Fig
2

SAVE THIS MANUAL: RETAIN FOR CONSUMER ’ S USE.
READ THESE INSTRUCTIONS COMPLETELY BEFORE
INSTALLING THE PRODUCT: FOR PRODUCT OR INSTALLATION QUESTIONS PLEASE CALL CUSTOMER SERVICE AT 1-800-221-3379.

Connect Black or Red
Supply Wire (Lead Wire) to:| Connect White Supply Wire (Neutral Wire) to:
---|---
Black wire| White wire
Parallel wire (round or smooth)| Parallel wire (square or ridged)
Clear brown, gold or black
wire without tracer| Clear brown, gold or black
wire with tracer
Insulated wire (other than green)
with copper conductor| Insulated wire (other than green)
with silver conductor

When parallel wires are used, the neutral wire is ridged down its length and the other wire is round and smooth (see illus.).

Signature Hardware 479806 Grinnell Vanity Light - Fig
4 INSTALLATION (FIG 1)

Position mounting bracket (A) so tabs are on the top and bottom. Attach mounting bracket (A) to junction box with junction box screws (B).
Strip 3/4” of insulation from ends of ﬁxture wires.
Twist the end of ﬁxture white wire to the end of house white wire together. Twist a wire nut onto ends of wires. Wrap electrical tape around wire nut and wires to secure
connection. Twist the end of ﬁxture black wire and the end of house black wire together. Twist a wire nut onto the ends of wires. Wrap electrical tape around wire nut and wires to secure connection. Loosen ground screw on mounting bracket (A). Wrap house ground wire around ground screw leaving enough ground wire to attach to ﬁxture ground wire. Twist the end of ﬁxture ground wire to the end of house ground wire together. Twist a wire nut onto ends of wires. Wrap electrical tape around wire nut and wires to secure connection.
Note: If you have electrical questions consult your local electrical code for approved grounding methods.
After wires are connected, carefully tuck wires inside junction box.
Raise ﬁxture to wall. Place backplate over mounting bracket (A). Align holes in tabs on top and bottom of mounting bracket (A) with holes in top and bottom of backplate. Thread one ﬁxture mounting screw (C) into each hole in backplate. Tighten ﬁxture mounting screws (C) to secure ﬁxture to wall. INSTALLATION (FIG 2)
Pass the hole in top of glass shade (E) over socket. Thread socket ring (F) onto socket. Tighten socket ring (F) to secure glass shade (E) to ﬁxture. DO NOT over tighten the socket ring (F).
Screw recommended bulbs (E26 Edison bulb type, not included) into sockets. Verify correct bulb wattage marked on socket of ﬁxture.
WARNING: DO NOT exceed maximum bulb wattage.