SIGNATURE HARDWARE 951706 Casanel Clear Glass Bell Pendant Light Instruction Manual

: June 8, 2024
: Signature Hardware

Table of Contents

BEFORE YOU BEGIN
GETTING STARTED
ADDITIONAL QUESTIONS?
FOR YOUR SAFETY
CARE INSTRUCTIONS
TOOLS AND MATERIALS
INSTALLATION (FIG 1)
INSTALLATION (FIG 2)
CUSTOMER SUPPORT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SIGNATURE HARDWARE 951706 Casanel Clear Glass Bell Pendant Light

SIGNATURE HARDWARE 951706 Casanel Clear Glass Bell Pendant
Light

BEFORE YOU BEGIN

We recommend consulting a professional if you are unfamiliar with installing electric fixtures. Signature Hardware accepts no liability for any damage to the faucet, plumbing, sink, counter top, or for personal injury during installation. Observe all local plumbing and building codes. Unpack and inspect the product for shipping damage. If any damage is found, contact our Customer Relations team via live chat at www.signaturehardware.com or by emailing support@siganturehardware.com.

GETTING STARTED

Ensure that you have gathered all the required materials that are needed for the installation.

ADDITIONAL QUESTIONS?

Still need help? Check out our Help Center at www.signaturehardware.com for product and warranty information, or contact us through live chat or by emailing support@signaturehardware.com.

FOR YOUR SAFETY

For Your Safety

WARNING: Be sure the electricity to the wires you are working on is shut off, either the fuse is removed or the circuit breaker is shut off. You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system. Read instructions carefully. If you are unclear as to how to proceed, consult a qualified electrician.

CARE INSTRUCTIONS

To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

TOOLS AND MATERIALS

Safety goggle
Step ladder
Wire strippers
Phillips screwdriver
Electrical tape
Wire cutters
Flathead screwdriver
Light Bulb (ST58 60 watt maximum

SAVE THIS MANUAL: RETAIN FOR CONSUMER’S USE.

INSTALLATION (FIG 1)

$Installation $Fig 1$$

Slip center column (L) along wire and thread onto nipple (M).
Place the glass (O) over the socket (N) and secure with the socket ring (P).
Install light bulb (Not provided ). Please do not exceed the maximum wattage capacity recommended on the socket.

Connect Black or Red Supply Wire (Lead Wire) to| Connect White Supply Wire (Neutral Wire) to:
---|---
Black wire| White wire
Parallel wire (round or smooth)| Parallel wire (square or ridged)
Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor

When parallel wires are used, the neutral wire is ridged down its length and the other wire is round and smooth (see illus.)

INSTALLATION (FIG 2)

Secure the mounting bar (A) to outlet box with the outlet box screws (B). Thread the nut (D) onto the nipple (E) . Insert the lock washer (C) and thread the nipple (E) into the mounting bar (A), then secure with the nut (D).
Thread the screw collar (G) onto the nipple (E). Slide the screw collar ring (H) and the canopy (F) over the chain (J). Open one link of chain (J), connect it to fixture loop (K) and close the link, then use quick link (I) to connect collar loop (G) and the top of chain (J).
BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.
Lace wires up through chain (I) and pass wires through holes in collar loop (H). We recommend lacing wire up through every other link of chain (I).
Please note: The ribbed wire will be a neutral wire, and the smooth wire will be a lead wire. The smooth wire will also have a printed temperature warning. Read instructions carefully. If you are unclear as to how to proceed, consult a qualified electrician.
Connect the white wire from the outlet box to the neutral wire (ribbed) from the fixture and the black wire from the outlet box to the lead wire (smooth) from the fixture. Cover the two wire connections using the two provided wire connectors. Wrap the two wire connections with electrical tape for a more secure connection. Connect the copper ground wires from the fixture and from the outlet box to the ground screw on the mounting bar.
Note: If you have electrical questions, consult your local electrical code for approved grounding methods
After wires are connected, tuck them carefully inside outlet box. place the canopy (F) on the ceiling and secure collar ring (H).