vtech VM350-2 Full Color Video Monitor User Guide

: June 8, 2024
: vtech

Quick start guide
VM350 VM350-2
Full Color Video Monitor Go to www.vtechphones.com to register your product for enhanced warranty support and the latest VTech product news.
For more support information

| |
---|---|---
https://vttqr.tv/?q=1VP86| https://vttqr.tv/?q=1VP87

TECHNICAL SPECIFICATIONS

Frequency control	Crystal controlled PLL synthesizer
Transmit frequency	Baby unit: 2405 – 2475 MHz Parent unit: 2405 – 2475 MHz
Channels	32
LCD	5″ Color LCD

(WQVOA 480×272 pixel)
Nominal effective range| Maximum power allowed by FCC and IC. Actual operating range may vary according to environmental conditions at the time of use.
Power requirements| Baby unit power adapter: Output: 6V DC @ 400mA Parent unit power adapter: Output: 5V DC @ 1A Parent unit battery: 3.8V 2100mAh Li-ion battery

Credits:
The Background Noise sound ﬁle was created by Caroline Ford, and is used under the Creative Commons license
The Stream Noise sound ﬁle was created by Caroline Ford, and is used under the Creative Commons license.
The Crickets At Night sound ﬁle was created by Mike Koenig, and is used under the Creative Commons license.
The Heart Beat sound ﬁle was created by Zarabadeu, and is used under the Creative Commons license.

Speciﬁcations are subject to change without notice.
© 2022 VTech Communications, Inc. All rights reserved.
06/22. VM350-X_QSG_V8.

Important safety instructions

The applied nameplate is located at the bottom of the baby unit’s base. When using your equipment, basic safety precautions should always be followed to reduce the risk of ﬁre, electric shock and injury, including the following:

Follow all warnings and instructions marked on the product.
Adult setup is required.
CAUTION: Do not install the baby unit at a height above 2 meters.
This product is not a substitute for adult supervision of the infant. Supervising the infant is the parent’s or caregiver’s responsibility. This product could cease operating, and therefore you should not assume it will continue working properly for any given period of time. Further, this is not a medical device and should not be used as such. This product is intended to assist you in supervising your baby.
Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower.
CAUTION: Use only the batteries provided. There may be a risk of explosion if a wrong type of battery is used for the parent unit. The batteries cannot be subjected to high or low extreme temperature and low air pressure at high altitude during use, storage or transportation. Disposal of batteries into ﬁre or a hot oven, or mechanically crushing or cutting or the batteries can result in an explosion. Leaving the batteries in an extremely high temperature surrounding environment can result in an explosion or the leakage of ﬂammable liquid of gas. Batteries subjected to extremely low air pressure may result in an explosion or the leakage of ﬂammable liquid or gas. Dispose of used battery according to the information in The RBRC seal.
Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product.
Use only adaptors and batteries listed below.
Power adapter information: VTech Telecommunications Ltd.
Model : VT05EUS06040 (Baby unit); VT05EUS05100 (Parent unit).
Rechargeable batteries information:
ZHONGSHAN TIANMAO BATTERY CO., LTD 3.8V 2100mAh Li-ion Battery (Model: I9300)
The power adapters are intended to be correctly oriented in a vertical or ﬂoor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, underthe-table or cabinet outlet.
For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible.
Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
Unplug the power cords before replacing batteries.
Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation.
Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped.
This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company.
Do not overload wall outlets or use an extension cord.
Do not place this product on an unstable table, shelf, stand or other unstable surfaces.
This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa
or rug. This product should never be placed near or over a radiator or heat register.
Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product.
To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the product other than speciﬁed access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.
You should test the sound reception every time you turn on the units or move one of the components.
Periodically examine all components for damage.
There is a very low risk of privacy loss when using certain electronic devices, such as baby monitors, cordless telephones, etc. To protect your privacy, make sure the product has never been used before purchase, reset the baby monitor periodically by powering off and then powering on the units, and power off the baby monitor if you will not use it for some time.
Children should be supervised to ensure that they do not play with the product.
The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

SAVE THESE INSTRUCTIONS

Cautions

Use and store the product at a temperature between 32o F and 104 o F.
Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source.
Batteries should not be exposed to excessive heat such as bright sunshine or ﬁre.
Warning—Strangulation Hazard—Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3 ft (0.9 m) away). Do not remove this tag.
Never place the baby unit inside the baby’s crib or playpen. Never cover the baby unit or parent unit with anything such as a towel or a blanket.
Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones.

Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless devices): Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:

Pacemaker patients

Should keep wireless devices at least six inches from the pacemaker.
Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON.

WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices.

Electromagnetic ﬁelds (EMF)
This VTech product complies with all standards regarding electromagnetic ﬁelds (EMF). If handled properly and according to the instructions in this user’s manual, the product is safe to be used based on scientiﬁc evidence available today.

What’s in the box

Connect the baby monitor

Install the battery
The parent unit runs on rechargeable battery or AC power. To continuously monitor your baby, make sure you use both battery and AC power at the same time.

Notes

Use only the battery supplied with this product.
If the parent unit will not be used for a long time, disconnect and remove the battery to prevent possible leakage.

Replace the battery
To replace the battery, press down on the battery compartment cover and pull it out, then follow the steps above to install the battery.

Connect the baby monitor
Notes

Use only the power adapters supplied with this product.
Make sure the baby monitor is not connected to the switch controlled electric outlet.
Connect the power adapters in a vertical or ﬂoor mount position only. The adapters’ prongs are not designed to hold the weight of baby monitor, so do not connect them to any ceiling, underthe-table, or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets.
Make sure the parent unit, the baby unit and the power adapter cords are out of reach of children.

Charge the parent unit battery
When you have connected and turned on the parent unit, the battery will be charged automatically.

Notes

Before using the baby monitor for the ﬁrst time, charge the parent unit battery for 12 hours. When the parent unit battery is fully charged, the battery icon becomes solid .
It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time, turn the parent unit off while charging.
The standby time varies depending on the sensitivity level you set, your actual use and the age of the battery.

Power on or off the baby monitor

Slide the ON/OFF switch to power on or off your baby unit.
Press and hold POWER to power on or off your parent unit.

Positioning the baby monitor

Caution
• Keep the baby unit out of the reach of your baby. Never place or mount the baby unit inside the baby’s crib or playpen.

Caution
• The default volume of your parent unit is level 4, and the maximum volume is level 7. If you experience high-pitched screeching noise from your baby monitor while positioning:
– Make sure your baby unit and parent unit are more than 3 feet (1 meter) apart, OR
– Lower the volume of your parent unit.

Note
• To avoid interference from other electronic devices, place your baby monitor at least 3 feet (1 meter) away from devices such as wireless routers, microwaves, cell phones and computers.

Status check

Once you power on both your baby unit and parent unit, your parent unit displays image from the baby unit, and the LINK LED light turns on.
The POWER LED light of baby unit turns on.

Basic operation – Parent unit

Adjust speaker volume
Press VOL+ / VOL- to adjust your parent unit speaker volume.

Zoom
Press to zoom in or out.

Talk to your baby unit
Press and hold TALK and speak to your parent unit. Your voice is transmitted to the baby unit. Release TALK when ﬁnish talking and hear your baby again.

Turn off the screen
Press and hold LCD ON/OFF to switch off the screen. You can still hear sound from the baby unit.

Tip
• Press any keys on the parent unit to turn on the screen again.

Use the menu
Press to enter the menu, choose a menu item, or save a setting. You can use the parent unit for advanced settings or operations, such as to play or stop the baby unit lullaby, or to adjust the baby unit sound sensitivity.

While in the menu:

Press to scroll among the menu options.
Press to select an item, or to save a setting.
Press to scroll among the sub-menus, or to adjust a setting.
Press to return to the previous menu options without changing the current setting.
Press /EXIT to return to live video.

Overview – Parent unit

1. LCD display
2. Antenna
3. LED lights
4. Microphone
5. POWER
6. TALK
7. Arrow keys
8. MENU/SELECT| 9. Power jack
10. VOL – / VOL +
11. VIEW /LCD ON/OFF
12 /EXIT
13. Speaker
14. Battery compartment cover
15. Stand
---|---

Overview – Baby unit

Pair hole
• Your baby units and parent unit provided are already paired.
POWER LED light
• On when the baby unit is turned on and is paired to the parent unit.
• Flashes when the baby unit is not being viewed; or when the link to the parent unit is lost.
Microphone
Camera
Infrared LEDs
Light sensor
ON/OFF switch
• Slide to turn on or off the baby unit.
Speaker
Power jack
Wall mount holes

Need help?

For operations and guides to help you using your video monitor, and for latest information and supports, go and check the online help topics and online FAQs.
Use your smartphone or mobile device to access our online help.

Go to https://help.vtechphones.com/vm350 or https://help.vtechphones.com/vm350-2; OR
Scan the QR code on the right. Launch the camera app or QR code scanner app on your smartphone or tablet. Hold the device’s camera up to the QR code and frame it. Tap the notiﬁcation to trigger the redirection of the online help.
-If the QR code is not clearly displayed, adjust your camera’s focus by moving your device closer or further away until it is clear.

You can also call our Customer Support at 1 800-595-9511 [in US] or 1 800-267-7377 [in Canada] for help.

| |
---|---|---
https://vttqr.tv/?q=1VP86| https://vttqr.tv/?q=1VP87

Parent unit icons

Main menu icons

Main menu	Sub-menu

Brightness
| • Adjust the parent unit’s LCD brightness.
Camera settings
| Baby unit speaker volume
• Adjust the baby unit’s speaker volume.
Monitoring mode (For VM350-2 only)
• Single mode
• Split mode
• Patrol mode
Lullaby
| **Play/Stop lullaby

**
• Select one of the soothing sounds, or white noise.

• Select one of the ﬁve melodies.
• Play all melodies.

• Set timer to stop playing the selected melody or soothing sound.
Alert tones
| • Set the parent unit to beep when the battery is low.
• Set the parent unit to beep when the link between the parent unit and the baby unit is lost.
• Set the conﬁrmation tone on or off when selecting an option in the menus.
• Set the parent unit to beep when the baby unit detects sounds while in Split
mode (For VM350-2 only).
Temperature
| ON/OFF
• Turn on/off temperature alert tone.
• Set the parent unit to beeps whenever the room temperature detected by the baby unit falls outside of the set temperature range.
• Set the minimum temperature.
• Set the maximum temperature.
• Set temperature display in Fahrenheit ( o F) or Celsius ( o C)
Sound activation – screen and audio
| ON/OFF Turn on/off sound activation
• Set sound activation on or off.
• When it is on, and the baby unit detects no sound, the parent unit screen stays off to save power. Once a sound is detected, the parent unit screen and speaker turns on automatically, and you can see and hear your baby. The parent unit will then turn off again after 50 seconds of no sound detection.
Note
• When the parent unit screen is off and it receives alerts, for example, link lost
between parent unit and baby unit, or battery is low, the parent unit screen and
speaker will turn on for 10 seconds.
VOX (Voice Activated Alert) Sensitivity
| • You can set VOX sensitivity level to activate parent unit screen and sound
when baby unit detects sounds that exceed certain levels. See Sound sensitivity and sound activation section.
Status icons|
| Connection status
• – Strong signal strength.
• – Moderate signal strength.
• – Low signal strength.
• – Weak signal strength.
| Split mode
(For VM350-2 only)
| Patrol mode
(For VM350-2 only)
| Current view status
• The baby unit number that is being viewed when in:
-Single CAM mode.
-Patrol mode (For VM350-2 only).
-Split mode (For VM350-2 only).
| Night vision – On
| Zoom – On
| Lullaby – On
| Two-way talk
• Displays when the parent unit is talking to the baby unit.
oF or oC| Real-time temperature
• Real-time temperature detected by the baby unit in Fahrenheit ( o F) or Celsius ( o C) (e.g. 57 o F or 14 o C).
| Temperature alert tone – On
| 9-level sound indicator
• indicates low sound level detected by the baby unit. indicates moderate
• sound level detected by the baby unit.
• indicates high sound level detected by the baby unit.
| Mute alert
• Displays when the parent unit speaker volume is set to off.
• Displays when the parent unit is talking to the baby unit.
| Battery status
• animates when the battery is charging.
• – battery is fully charged.
• – battery is low and needs charging.
Alert icons| • Displays when parent unit’s battery is low and needs charging.
• Displays when connection between parent unit and baby unit is lost.
• Displays when sound is detected at a baby unit when in Split view. (For VM350-2 only)
• Baby unit detects temperature reaches or exceeds the set maximum.
• Baby unit detects temperature is at or is lower than the set minimum.

Sound sensitivity and sound activation

Adjust sound detection sensitivity
You can turn on Sound activation and adjust the VOX sensitivity to detect sounds and turn on the parent unit while its screen is switched off or dimmed.
When the baby unit detects sounds that exceed certain levels, the parent unit screen will turn on and the baby unit starts transmitting the sounds to the parent unit, and you can see and hear your baby.
If you turn off Sound activation, you will hear sounds from the baby unit all the time, even when the parent unit screen is switched off.
If you have turned on sound alert, the parent unit beeps when the baby unit detect sounds while in Split mode (*For VM350-2 only).

---|---|---|---|---|---
Description| (Default setting) The parent unit screen and speaker turn on for very small sounds, including background noises from your baby’s room.| The parent unit screen and speaker turn on for soft babbling and louder sounds from your baby. The parent unit remains quiet when your baby sleeps soundly.| The parent unit screen and speaker turns on for loud babbling and louder sounds from your baby.
The parent unit remains quiet when your baby makes soft sounds.| The parent unit
screen and speaker turn on for crying and louder sounds
from your baby.
The parent unit remains quiet when your baby makes soft sounds.| The parent unit screen and speaker turn on for loud crying or screeching sounds from your baby. The parent unit remains quiet when your baby makes soft sounds.

Sound activated screen and audio

When Sound activation is on, the parent unit screen stays off to save power when the baby unit detects no sound.
Once the baby unit detects sounds that are louder than the chosen sound sensitivity level, the parent unit screen and speaker turn on automatically. The parent unit will then turn off again after 50 seconds of no sound detection.

Note
• If you have muted the parent unit speaker, only the parent unit screen will turn on when a sound is detected.

Night vision

The baby unit has infrared LEDs that allow you to see your baby clearly at night or in a dark room. When the baby unit being viewed detects low light levels, the infrared LEDs are switched on automatically. The images from the baby unit are in black and white, and appears on the screen.

Notes
• It is normal if you see a short white glare on your parent unit screen as the baby unit is adapting to the dark environment.
• When the infrared LEDs are on, the images are in black and white. This is normal.

Tip
• Depending on the surroundings and other interfering factors, like lightings, objects, colors and backgrounds, the video quality may vary. Adjust the baby unit’s angle or place the baby unit at a higher level to prevent glare and blurry display.

Dim mode

The parent unit display will dim to conserve energy after 10 minutes of inactivity, in which there is neither key pressed nor alert received from the baby unit.

For VM350-2 only

Status check – Two baby units
If you are viewing baby unit , the POWER LED light of baby unit turns on. As baby unit is not being viewed, its POWER LED light ﬂashes.

Note
• If you power on only one baby unit, you may see the parent unit displaying and then , and the LINK LED light ﬂashing.
• Press VIEW in Single CAM or Patrol mode to switch to the baby unit you have powered on.

Change different views – Single CAM

In Single CAM or Patrol mode, press VIEW to switch between the image of baby units and

Change different views – Patrol

Select Patrol as your monitoring mode to alternately view the image from baby units and every 10 seconds.

Change different views – Split
Select Split as your monitoring mode to view the images from both baby units at once.

The RBRC seal

The RBRC seal on the lithium-ion battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States and Canada.
The program provides a convenient alternative to placing used lithium-ion batteries into the trash or municipal waste, which may be illegal in your area.
VTech’s participation makes it easy for you to drop off the spent battery at local retailers participating in the program or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY ® for information on Li-ion battery recycling and disposal bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our environment and conserving natural resources.
The RBRC seal and 1-800-8-BATTERY® are registered trademarks of Call2recycle, Inc.

FCC and IC regulations

FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modiﬁcations to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The baby unit shall be installed and used such that parts of all persons’ body are maintained at a distance of approximately 8 in (20 cm) or more. The transmitter and antenna of the parent unit shall be held at least 1 in (2.5 cm) from your face.
This Class B digital apparatus complies with Canadian requirement: CAN ICES-3 (B)/NMB-3(B)

Industry Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
The term ‘’IC:‘’ before the certiﬁcation/registration number only signiﬁes that the Industry Canada technical speciﬁcations were met.
This product meets the applicable Innovation, Science and Economic Development Canada technical speciﬁcations.

RF radiation exposure statement
The baby unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should be installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons’ body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies also with Industry Canada RSS-102 with respect to Canada’s Health Code 6 for Exposure of Humans to RF Fields.

California Energy Commission battery charging testing mode
This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor is set up to comply with the energy- conserving standards right out of the box. Follow the instructions to install and charge the battery. The CEC battery charging testing mode is activated while charging. Even if the parent unit is paired to baby units, the CEC battery charging testing mode is activated while it is powered off and charging.

Mount the baby unit on dry wall (optional)

Items to purchase
You will need to purchase the following items separately to mount your baby unit:

Note
• The types of screws and anchors you need depend on the composition of the wall.

Note
• Check for reception strength and camera angle before drilling the holes.

Use a pencil to mark two holes in parallel.
Make sure they are the same distance apart as the wall mount holes on the baby unit.

Drill two holes in the wall.
If you drill the holes into a stud, go to step 3. –
OR
If you drill the holes into an object other than a stud, insert the wall anchors into the holes. Tap gently on the ends with a hammer until the wall anchors are ﬂush with the wall.

Insert the screws into the holes and tighten the screws until only 1/4 inch of the screws are exposed.

Align the wall mount holes at the bottom of the baby unit with the screws on the wall. Slide the baby unit down until it locks into place.

Adjust the camera angle.

Limited warranty

What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or “you”) that the Product and all accessories provided in the sales package (“Product”) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product operating instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United States of America and Canada.

What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service representative will repair or replace at VTech’s option, without charge, a Materially Defective Product. If we repair the Product, we may use new or refurbished replacement parts. If we choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment. Repair or replacement of the Product, at VTech’s option, is your exclusive remedy. VTech will return the repaired or replacement Products to you in working condition. You should expect the repair or replacement to take approximately 30 days.

How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs or replaces a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies to the repaired or replacement Product for a period of either (a) 90 days from the date the repaired or replacement Product is shipped to you or (b) the time remaining on the original one-year warranty; whichever is longer.

What is not covered by this limited warranty?
This limited warranty does not cover:

Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, ﬁre, water or other liquid intrusion; or
Product that has been damaged due to repair, alteration or modiﬁcation by anyone other than an authorized service representative of VTech; or
Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or antenna systems; or
Product to the extent that the problem is caused by use with non-VTech accessories; or
Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been removed, altered or rendered illegible; or
Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for commercial or institutional purposes (including but not limited to Products used for rental purposes); or
Product returned without a valid proof of purchase (see item 2 below); or
Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit.

How do you get warranty service?
To obtain warranty service in the USA, please visit our website at www.vtechphones.com or call 1 800-595-9511. In Canada, go to www.vtechcanada.com
or call 1 800-267-7377.
NOTE: Before calling for service, please review the user’s manual – a check of the Product’s controls and features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location. VTech will return repaired or replaced Product under this limited warranty. Transportation, delivery or handling charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you authorize the cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by this limited warranty.

What must you return with the Product to get warranty service?

Return the entire original package and contents including the Product to the VTech service location along with a description of the malfunction or difﬁculty; and
Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and the date of purchase or receipt; and
Provide your name, complete and correct mailing address, and telephone number.

Other limitations
This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral communications related to this Product. VTech provides no other warranties for this Product. The warranty exclusively describes all of VTech’s responsibilities regarding the Product. There are no other express warranties. No one is authorized to make modiﬁcations to this limited warranty and you should not rely on any such modiﬁcation. State/Provincial Law Rights: This warranty gives you speciﬁc legal rights, and you may also have other rights, which vary from state to state or province to province.
Limitations: Implied warranties, including those of ﬁtness for a particular purpose and merchantability (an unwritten warranty that the Product is ﬁt for ordinary use) are limited to one year from the date of purchase. Some states/ provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost proﬁts or revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase.

Disclaimer and Limitation of Liability

VTech Communications, Inc. and its suppliers assume no responsibility for any damage or loss resulting from the use of this user’s manual. VTech Communications, Inc. and its suppliers assume no responsibility for any loss or claims by third parties that may arise through the use of this product.

Company: VTech Communications, Inc.
Address: 9020 SW Washington Square Road – Ste 555 Tigard, OR 97223, United States
Phone: 1 800-595-9511 in the U.S. or 1 800-267-7377 in Canada

CONFORMS TO UL STD. 62368-1
CERTIFIED TO CSA STD.
C22.2 NO.62368-1

Documents / Resources

| vtech VM350-2 Full Color Video Monitor [pdf] User Guide
80-1383-01, 80138301, EW780-1383-01, EW780138301, VM350, VM350-2, Full Color Video Monitor, VM350-2 Full Color Video Monitor, Color Video Monitor, Video Monitor, Monitor
---|---