tp-link 5-8-Port 2.5G Multi-Gigabit Desktop Switch Installation Guide

: June 9, 2024
: tp-link

Table of Contents

Panel Explanation
Specifications
Frequently Asked Questions (FAQ)
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

tp-link 5-8-Port 2.5G Multi-Gigabit Desktop Switch Installation Guide

Panel Explanation

Power

On: Power on
Off: Power of

Kensington Security Slot

Secure the lock (not provided) into the slot to prevent the device from being stolen.

Port LED

When one of the LED is on/flashing
On: Connecting to a device but no activity
Flashing: Transmitting or receiving data

Left LED (2.5G)
Green: Running at 2.5 Gbps
Flashing: Transmitting or receiving data

Right LED (1G/100M)
Green: Running at 1 Gpbs
Yellow: Running at 100 Mbps
Flashing: Transmitting or receiving data

Note:
For simplicity, we will take TL-SG105-M2 for example in this Guide.

CONNECTION

Specifications

General Specifications

Standard IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3bz, IEEE802.3x, IEEE802.1p

Protocol CSMA/CD

Network Media (Cable)

100Base-TX: UTP category 5 cable or above (max. 100 m)
1000Base-T: UTP category 5e cable or above (max. 100 m)
2.5GBase-T: UTP category 5e cable or above (max. 100 m)

Interface
5/8 100 Mbps/1 Gbps/2.5 Gbps Auto-Negotiation RJ45 Ports

Switching Capacity
TL-SG105-M2: 25 Gbps
TL-SG108-M2: 40 Gbps

Transfer Method
Store-and-Forward

MAC Address Learning
Automatically learning, automatically aging

Frame Forward Rate
100Base-TX: 148810pps/Port
1000Base-T: 1488095pps/Port
2.5GBase-T: 3720238pps/Port

Environmental and Physical Specifications

Operating Temperature 0˚C to 40˚C (32˚F to 104˚F)
Storage Temperature -40˚C to 70˚C (-40˚F to 158˚F)
Operating Humidity 10% to 90% RH non-condensing
Storage Humidity 5% to 90% RH non-condensing

Frequently Asked Questions (FAQ)

Q1. The Power LED is not lit.

The Power LED should be lit when the power system is working normally. If the Power LED is not lit, check as follows:
A1: Make sure the power adapter is connected to the switch with power source properly.
A2: Make sure the voltage of the power supply meets the requirements of the input voltage of the switch.
A3: Make sure the power source is ON.

Q2. The right and left LED are not lit when a device is connected to the corresponding port.

It is recommended that you check the following items:
A1: Make sure that the cable connectors are firmly plugged into the switch and the device.
A2: Make sure the connected device is turned on and works normally.
A3: The cable must be less than 100 meters long (328 feet).

EU declaration of conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives (EU)2015/863, 2014/30/EU, 2014/35/EU, 2009/125/EC and 2011/65/EU.
The original EU declaration of conformity may be found at https://www.tplink.com/en/ce.

UK declaration of conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016.
The original UK declaration of conformity may be found at https://www.tplink.com/support/ukca/

Safety Information

Keep the device away from water, fire, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
Do not use damaged charger or USB cable to charge the device.
Do not use any other chargers than those recommended.
Adapter shall be installed near the equipment and shall be easily accessible.

Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.