Inovelli Light Strip LZW45 Manual
- June 8, 2024
- inovelli
Table of Contents
- Inovelli
- Light Strip
- SKU: LZW45
- Quickstart
- Important safety information
- What is Z-Wave?
- Product Description
- Prepare for Installation / Reset
- Inclusion/Exclusion
- Quick trouble shooting
- Association – one device controls an other device
- Configuration Parameters
- Parameter 1: Number of Pixels
- Parameter 10: State Power Restored
- Parameter 17: Active power reports
- Parameter 18: Periodic reports
- Parameter 19: Active energy reports
- Parameter 2: Dimming Speed
- Parameter 21: Quick Strip Effect
- Parameter 22: Custom Effect Parameter 1
- Parameter 23: Custom Effect Parameter 2
- Parameter 24: Custom Effect Parameter 3
- Parameter 3: Ramp Rate
- Parameter 30: Custom Effect Parameter 4
- Parameter 31: Pixel Effect
- Parameter 4: Minimum Level
- Parameter 5: Maximum Level
- Parameter 51: Button Delay
- Parameter 6: Auto Off Timer
- Parameter 7: Default Level(Local)
- Parameter 8: Default Level (Z-Wave)
- Parameter 9: Default Color&Temp
- Technical Data
- Supported Command Classes
- Controlled Command Classes
- Explanation of Z-Wave specific terms
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Inovelli
Light Strip
SKU: LZW45
Quickstart
This is a
secure
Color Switch DT
for
.
To run this device please connect it to your mains power supply.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in
this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any
loss or damage resulting from failure to comply with the instructions in this
manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal
instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart
Home. This
device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message ( two-
way
communication) and every mains powered node can act as a repeater for other
nodes
( meshed network ) in case the receiver is not in direct wireless range of
the
transmitter.
This device and every other certified Z-Wave device can be used together
with any other
certified Z-Wave device regardless of brand and origin as long as both are
suited for the
same frequency range.
If a device supports secure communication it will communicate with other
devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to
maintain
backward compatibility.
For more information about Z-Wave technology, devices, white papers etc.
please refer
to www.z-wave.info.
Product Description
The first addressable RGBTW (Multi-Color + Tunable White) Z-Wave LED Strip & Controller kit from Inovelli which has 45+ built in animations, the ability to build your own animations and heads up notifications (ie: garage door is left open, LED strip can flash red).
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory
default
state. Please make sure to reset the device into factory default. You can do
this by
performing an Exclusion operation as described below in the manual. Every
Z-Wave
controller is able to perform this operation however it is recommended to use
the primary
controller of the previous network to make sure the very device is excluded
properly
from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-
specific
installation guidelines/norms may do works with mains power. Prior to the
assembly of
the product, the voltage network has to be switched off and ensured against
re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The
device needs
to be added to an existing wireless network to communicate with the
devices of this network.
This process is called Inclusion.
Devices can also be removed from a network. This process is called
Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network.
This
controller is turned into exclusion respective inclusion mode. Inclusion and
Exclusion is
then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Association – one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one
device
controlling another device is called association. In order to control a
different
device, the controlling device needs to maintain a list of devices that will
receive
controlling commands. These lists are called association groups and they are
always
related to certain events (e.g. button pressed, sensor triggers, …). In case
the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a ‘Basic Set’
Command.
Association Groups:
Group NumberMaximum NodesDescription
1| 5| Members of this group will receive unsolicited messages related to the
status of the controller.
---|---|---
2| 5| Sends On & Off commands to associated devices. (1. Single press UP
button sends BasicSet (0xFF) and 2. Single press Down sends BasicSet (0x00)
3| 5| Sends set level commands to associated devices when the up/down button
is pressed.(1. Hold & Release Up or Down button sends SwitchMultiLevelSet
which keeps associated devices in sync with this device. 2. Single press Up
button sends SwitchMultiLevelSet(0xFF) and 4. Single press Down button sends
SwitchMultiLevelSet(0x00)
4| 5| Sends start / stop level change to associated devices.(1. Hold Up button
sends SW_MULTILEVEL_START_LEVEL_CHANGE (Up)2: Hold Down button sends
SW_MULTILEVEL_START_LEVEL_CHANGE (Down) 3. Release Either button sends
SW_MULTILEVEL_STOP_LEVEL_CHANGE
Configuration Parameters
Z-Wave products are supposed to work out of the box after inclusion, however
certain configuration can adapt the function better to user needs or unlock
further
enhanced features.
IMPORTANT: Controllers may only allow configuring
signed values. In order to set values in the range 128 … 255 the value sent in
the application shall be the desired value minus 256. For example: To set a
parameter to 200 it may be needed to set a value of 200 minus 256 = minus
56.
In case of a two byte value the same logic applies: Values greater than 32768
may
needed to be given as negative values too.
Parameter 1: Number of Pixels
When individually addressable LEDs are used, this parameter tells the
controller the number of pixels that are attached. 0 – Automatic recognition
of pixels. 1..130 – Manually set the number of pixels.
Size: 1 Byte, Default Value: 0
SettingDescription
0 | Automatic Recognition of Pixels |
---|---|
1 – 130 | Manual input of Pixels (1 = 1 Pixel, 2 = 2 Pixels, etc) |
Parameter 10: State Power Restored
The state the switch should return to once power is restored after power
failure. 0 – Off. 1 – Default Color / Level (Parameter 9). 2 – Previous
Size: 1 Byte, Default Value: 2
SettingDescription
0 | Off |
---|---|
1 | Returns to the default color / level as set in Parameter 9 |
2 | Returns to the previous setting before loss of power |
Parameter 17: Active power reports
The power level change that will result in a new power report being sent.
The value is a percentage of the previous report. 0 = disabled.
Size: 1 Byte, Default Value: 10
SettingDescription
0 | Disabled |
---|---|
1 – 100 | Set the percentage level change of the previous report (1 = 1%, 2 = |
2%, etc)
Parameter 18: Periodic reports
Time period between consecutive power & energy reports being sent (in
seconds). The timer is reset after each report is sent.
Size: 2 Byte, Default Value: 3600
SettingDescription
0 | Disabled |
---|---|
1 – 32767 | Set the time period in seconds (1 = 1 second, 2 = 2 seconds, etc) |
Parameter 19: Active energy reports
Energy reports Energy level change which will result in sending a new energy
report. Available settings: 0 – energy reports disabled, 1-127 (0.01-1.27 kWh)
– report triggering threshold, Default setting: 10 (0.1 kWh)
Size: 1 Byte, Default Value: 10
SettingDescription
0 | Disabled |
---|---|
1 – 127 | Report triggering threshold (10 = 0.1 kWh) |
Parameter 2: Dimming Speed
This changes the speed in which the lightstrip dims up or down. A setting of
0 should turn the light immediately on or off (almost like an on/off switch).
Increasing the value should slow down the transition speed. 0 – Instant, 1 –
Fast .. 98 – Slow
Size: 1 Byte, Default Value: 3
SettingDescription
0 | Instant on |
---|---|
1 – 98 | Speed of dimming up or down (1 = fast, 98 = slow) |
Parameter 21: Quick Strip Effect
Turn on a quick effect that is similar to the LED notifications on our
dimmers and switches. See website for details.
https://inovelli.com/lzw45/parameters
Size: 4 Byte, Default Value: 0
SettingDescription
0 – 2147483647| See website for further instructions:
https://inovelli.com/lzw45/parameters
---|---
Parameter 22: Custom Effect Parameter 1
A custom effect with up to 4 actions can be turned on with correct input for
parameters 22-24, 30. This parameter controls the color and transition of
those actions. See website for details. https://inovelli.com/lzw45/parameters
Size: 4 Byte, Default Value: 0
SettingDescription
0 – 2139062143| See website for further instructions:
https://inovelli.com/lzw45/parameters
---|---
Parameter 23: Custom Effect Parameter 2
A custom effect with up to 4 actions can be turned on with correct input for
parameters 22-24, 30. This parameter controls the level of those actions. See
website for details.https://inovelli.com/lzw45/parameters
Size: 4 Byte, Default Value: 0
SettingDescription
0 – 1667457891| See website for further instructions:
https://inovelli.com/lzw45/parameters
---|---
Parameter 24: Custom Effect Parameter 3
A custom effect with up to 4 actions can be turned on with correct input for
parameters 22-24, 30. This parameter controls the duration of those actions.
See website for details. https://inovelli.com/lzw45/parameters
Size: 4 Byte, Default Value: 0
SettingDescription
0 – 1010580540| See website for further instructions:
https://inovelli.com/lzw45/parameters
---|---
Parameter 3: Ramp Rate
This changes the speed in which the lightstrip turns on or off. For example,
when a user sends the switch a basicSet(value: 0xFF) or basicSet(value: 0x00),
this is the speed in which those actions take place. A setting of 0 should
turn the light immediately on or off (almost like an on/off switch).
Increasing the value should slow down the transition speed. A setting of 99
should keep this in sync with parameter 2. 0 – Instant. 1 – Fast .. 98 – Slow.
99 – Keep in sync with parameter 2
Size: 1 Byte, Default Value: 99
SettingDescription
0 | Instant on |
---|---|
1 – 99 | Speed of turning on/off (1 = fast, 99 = slow) |
Parameter 30: Custom Effect Parameter 4
A custom effect with up to 4 actions can be turned on with correct input for
parameters 22-24, 30. This parameter controls the number of iterations, the
end effect, and the scale of the duration in parameter 24. See website for
details. https://inovelli.com/lzw45/parameters
Size: 4 Byte, Default Value: 0
SettingDescription
0 – 197375| See website for further instructions:
https://inovelli.com/lzw45/parameters
---|---
Parameter 31: Pixel Effect
Turn on an effect that utilizes the individually addressable LEDs. Byte 0 =
Effect, Byte 1 = Level
Size: 2 Byte, Default Value: 0
SettingDescription
0 – 32767| See website for further instructions:
https://inovelli.com/lzw45/parameters
---|---
Parameter 4: Minimum Level
The minimum level that the strip can be dimmed to. Useful when the user has
an LED strip that does not turn on or flickers at a lower level.
Size: 1 Byte, Default Value: 1
SettingDescription
1 – 45 | Percent value of the minimum dim level (1 = 1%, 2 = 2%, etc) |
---|
Parameter 5: Maximum Level
The maximum level that the strip can be dimmed to. Useful when the user has
an LED strip that reaches its maximum level before the dimmer value of 99.
Size: 1 Byte, Default Value: 99
SettingDescription
55 – 99 | Percent value of the maximum dim level (55 = 55%, 56 = 56%, etc) |
---|
Parameter 51: Button Delay
The 700ms delay that occurs after pressing the physical button to turn the
switch on/off is removed. Consequently this also removes the following scenes:
2x, 3x, 4x, 5x tap. Still working are the 1x tap, held, released, and the
level up/down scenes.
Size: 1 Byte, Default Value: 1
SettingDescription
0 | Yes – Disable 700ms delay |
---|---|
1 | No – Do not disable 700ms delay |
Parameter 6: Auto Off Timer
Automatically turns the strip off after this many seconds. When the strip is
turned on a timer is started that is the duration of this setting. When the
timer expires, the strip is turned off. 0 – Auto off is disabled
Size: 2 Byte, Default Value: 0
SettingDescription
0 | Auto-off is disabled |
---|---|
1 – 32767 | Amount of seconds until the lightstrip turns off automatically (1 = |
1 second, 2 = 2 seconds, etc)
Parameter 7: Default Level(Local)
Default level for the strip when it is powered on from the local switch. A
setting of 0 means that the switch will return to the level that it was on
before it was turned off. 0 – Previous
Size: 1 Byte, Default Value: 0
SettingDescription
0 | Returns lightstrip to the previous level prior to being turned off |
---|---|
1 – 99 | Percent level to turn the lightstrip to when turned on (1 = 1%, 2 = |
2%, etc)
Parameter 8: Default Level (Z-Wave)
Default level for the dimmer when it is powered on from a Z-Wave command
(i.e. BasicSet(0xFF). A setting of 0 means that the switch will return to the
level that it was on before it was turned off. 0 – Previous
Size: 1 Byte, Default Value: 0
SettingDescription
0 | Returns lightstrip to the previous level prior to being turned off |
---|---|
1 – 99 | Percent level to turn the lightstrip to when turned on (1 = 1%, 2 = |
2%, etc)
Parameter 9: Default Color&Temp
Byte(3-2): Values between 2700-6500 represent a color temperature.
Byte(1-0): Values between 1-360 represent the color on the Hue color wheel.
The value of 361 represents a random color and a value of 0 represents the
previous color.
Size: 4 Byte, Default Value: 0
SettingDescription
0 | Returns the lightstrip to the previous color when turned on |
---|---|
1 – 360 | Represents the values of the hue color wheel |
2700 – 6500 | Represents the values of color temperature (Kelvins) where 2700 |
is warm white and 6500 is cool white
Technical Data
Hardware Platform | ZGM130 |
---|---|
Device Type | Color Switch DT |
Network Operation | Always On Slave |
Firmware Version | HW: 1 FW: 1.20 |
Z-Wave Version | 7.13.4 |
Certification ID | ZC12-20110133 |
Z-Wave Product Id | 0x031E.0x000A.0x0001 |
Color | White |
IP (Ingress Protection) Rated | ok |
Firmware Updatable | Updatable by Consumer by RF |
Outdoor Use | ok |
Z-Wave Scene Type | Central Scene |
Communications Protocol | Z-Wave Z/IP |
Security V2 | S2_UNAUTHENTICATED ,S2_AUTHENTICATED |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |
Supported Command Classes
- Application Status
- Association Grp Info V3
- Association V2
- Basic V2
- Central Scene V3
- Configuration V4
- Device Reset Locally
- Firmware Update Md V5
- Indicator V3
- Manufacturer Specific V2
- Meter V3
- Multi Channel Association V3
- Powerlevel
- Protection V2
- Security
- Security 2
- Supervision
- Switch Color V3
- Switch Multilevel V4
- Transport Service V2
- Version V3
- Zwaveplus Info V2
Controlled Command Classes
- Basic V2
- Protection V2
- Switch Multilevel V4
Explanation of Z-Wave specific terms
-
Controller — is a Z-Wave device with capabilities to manage the network.
Controllers are typically Gateways,Remote Controls or battery operated wall controllers. -
Slave — is a Z-Wave device without capabilities to manage the network.
Slaves can be sensors, actuators and even remote controls. -
Primary Controller — is the central organizer of the network. It must be
a controller. There can be only one primary controller in a Z-Wave network. -
Inclusion — is the process of adding new Z-Wave devices into a network.
-
Exclusion — is the process of removing Z-Wave devices from the network.
-
Association — is a control relationship between a controlling device and
a controlled device. -
Wakeup Notification — is a special wireless message issued by a Z-Wave
device to announces that is able to communicate. -
Node Information Frame — is a special wireless message issued by a
Z-Wave device to announce its capabilities and functions.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>