inovelli LZW45 Lightstrip Instruction Manual
- June 5, 2024
- inovelli
Table of Contents
LZW45 | Lightstrip
Red Series
Thank You.
Thank you for taking the chance on us. We are truly humbled to be a part of
your smart home journey and know that out of the many companies out there, you
trusted us to make your life simpler and we don’t take that for granted. Our
mission is to provide the best products, with the best customer support, at
the best prices. Sure, every company says that… but we’d like to think we’re
different. Why? Well, because we have our own smart homes, with our own
desires to make our life simpler through home automation. We wake up every day
to lights turning on to different colors based on the weather, coffee
automatically brewing before we leave for work, and the thermostat changing
based on our schedules. We take our nerdiness seriously by engaging in online
groups and designing our products around community suggestions and needs. We
don’t pretend to be a multi-billion dollar corporation worried about
shareholders and the bottom line. We’re ok with being the little guy. The
underdog, looking out for the best interests of people like us… the everyday
smart home enthusiast who is passionate about moving the industry forward and
we wouldn’t have it any other way. So again, from the bottom of our hearts,
thank you for trusting us.
Z-Wave SmartStart
This device supports Z-Wave’s new SmartStart feature. Please do not throw out
the card within the box that has your unique QR Code with your DSK (Device
Specific Key). This QR Code can also be found on the back of the switch (metal
plate) and box. HUB Installation Instructions.
All HUB’s are different, so why should your installation instructions be the
same? Below you’ll find a QR Code to specific instructions for your HUB (NOTE:
If you don’t see your HUB, please scan the, “Other” QR Code). As you can
imagine, it’s hard to keep written instructions up to date with all the
HUB/App changes, so the most recent instructions will be on the site. However,
if you’re a manual guy/gal, we get it, please see Page 7 for more details! If
ever you run into any issues, please reach out to us at:
contact@inovelli.com.
| | |
---|---|---|---
http://inovelli.com/lzw45/setup/smartthings|
http://inovelli.com/lzw45/setup/hassio|
http://inovelli.com/lzw45/setup/hubitat|
http://inovelli.com/lzw45/setup/other
Technology Behind the Lightstrip
The Inovelli Lightstrip is an advanced smart home lighting product that brings new functionality to this product category. It runs off of the Z-Wave 700 series chip and supports all of its bells and whistles (S2 security, Smart Start, increased range, etc.). It also has some of the most advanced features seen on a commercial product of its kind. Individually addressable LEDs, dozens of pre-defined color effects, customizable effects, energy monitoring, scene control, digital display, and more. It definitely lives up to the Inovelli brand name.
**** TO AVOID PERSONAL INJURY AND/OR POSSIBLE PRODUCT DAMAGE, THE FOLLOWING CAUTIONS SHOULD BE FOLLOWED:
- Disconnect power at fuse or circuit breaker before installing or servicing.
- To prevent early device failure, the device should only be installed in operating environments ranging between(0°C and +40°C) 4°F and +04°F
- The device has passed the ETL for damp locations, but it is recommended to be used in dry locations only.
- Lightstrip dims via wireless control and will not operate with a dimmer switch.
- Not for use in totally enclosed luminaires.
- Not for use in emergency light fixtures or exit signs.
- Ensure the fixture can support the added weight of the light strip.
- Do not clean the light strip when it is on and connected to the power supply.
- Do not place the light strip on hot surfaces.
- Dispose of this device in accordance with disposal laws in your area.
- Do not use if the light strip is broken or missing. If broken or damaged make sure you dispose of it safely. There are risks of electric shock.
- Do not interconnect parts of this light strip with parts of another manufacturer’s light strip.
- Interconnection shall be made only by the use of the supplied connectors. Any open ends must be sealed-off before use.
- maximum system length that may be interconnected is 5 meters; a maximum number of strips or max system wattage that may be interconnected is 20W.
SPECIAL NOTES FOR CONNECTED LIGHT STRIP:
- The fixture is based on the Z-Wave protocol, which is used to turn it on/off and change its brightness.
- Not suitable for operation on a dimmable circuit (such as a traditional wall dimmer for incandescent lamps or LED lamps). Dimming is only possible via Z-Wave.
- For non-replaceable light sources: The light source of this fixture is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.
- Linkable The product is composed of 5 strips of 5 feet and 2 strips of 0.5 feet and supports a total length of 16 feet. Connect the male pin at the strip light input to the female pin at the other one.
Z-Wave Distance Notes
It’s important to understand the limitations of the distances of Z-Wave so
that your hub and device can communicate effectively.
This device is using the new Z-Wave 700 series chip which greatly improves the
wireless range. You may notice when working with this device that there is an
improvement in communication compared to older Z-Wave devices. If you are
still unsure of the distance between your device and your hub, please consult
pages 3 & 4 to help you calculate and understand possible range scenarios with
your Z-Wave devices.
Z-Wave Range Worksheet.
Feel free to use the below worksheet to give an estimate on where you can put
your Z-Wave device relative to your HUB (or another Z-Wave repeater). Below is
an example of how to use the sheet, using, “Example 1” from Page 3.
Example #1–Original Z-Wave Range
Starting Distance | Obstacle | Signal Depreciation | Ending Distance |
---|---|---|---|
100m // 328ft | Inner Wall | 40% | 60m // 197ft |
60m // 197ft | Inner Wall | 40% | 36m // 118ft |
36m // 118ft | Wood Stairs | 60% | 14m // 47ft |
14m // 47ft | Inner Wall | 40% | 9m // 28ft |
9m 1/ 28ft | Wood Cabinet | 50% | 5m // 15ft |
5m // 15ft | Wood Table & Chairs | 60% | 2m // 7ft |
For the starting Distance, use 100m. Then look directly from your HUB to
wherever you’d like to put the outlet and see what obstacles are in the way.
Then list those
obstacles on the worksheet below (using the charts from Page 2).
Starting distance| Obstacle| signal Depreciation| Ending
Distance
---|---|---|---
Best Practices for Pairing the device to Your Hub/Gateway:
Now that you’ve read how to calculate the Z-Wave range and have determined the
best location to put your device, it’s important to understand some best
practices of how to pair it. Below are a few things to keep in mind when you
start your individualized pairing instructions (Pages 7-8).
NOTE: As mentioned on Page 2, please make sure your device is within
Z-Wave range first.
Calculate the Maximum Distance From the Worksheet Above and Place Well
Within That Distance
Please use the worksheet above to calculate your maximum distance. This will
save us both the headache of offline devices. Remember to add all objects that
could potentially be in the way and it’s our recommendation to be conservative
with the
distance numbers.
If the device is Not Including, Try an Exclusion
Z-Wave devices can only be included (paired) to one HUB at a time. Sometimes,
what happens is that the factory tests the devices by including it to their
network and forgets to remove the device from their network, causing the
device to believe that it’s paired to the factory HUB. While this is extremely
rare, it may happen. This can also happen if you purchased this switch used.
Follow the exclusion instructions located on Page 8 if you run into issues or
check the range to make sure you are within range of the HUB. Or, if you’ve
installed it already, simply hold down the config button for (5) seconds to
see whether or not the device is within range. If it lights up GREEN and stays
GREEN after you’ve let go, then it’s within range, however, if it lights up
RED, then you are not within range.
About Z-Wave.
Z-Wave is an incredible technology. With it powering your home, you can choose
from over 600 companies and 2100 products, all of which will work with each
other. The more devices, the more stable the network. The purpose of this
portion of the manual is to help you understand how Z-Wave works (in layman’s
terms) as well as help you organize an efficient Z-Wave network, setting you
up for success in the long run. After all, we’re assuming you’ll want more
than one smart home device!
Z-Wave Network | Using Devices That Repeat Signals.
As referenced in the intro, Z-Wave can be used with a few devices or it can be
used to build a large network. Below you’ll see two examples. In the first
example, a user has a HUB which is looking for Z-Wave devices within its
radius. Z-Wave devices outside this radius will not be found and need to
either be moved within the radius or use a repeating device to reach it. The
second example shows how a repeater can be used to reach a device outside of
the initial radius. Keep this in mind when building your own network and make
sure to use the range estimator below.
NOTE: Z-Wave range will never be a perfect circle due to walls, furniture,
etc. The above is for reference only, please use the, “Range Estimator” below
and the Worksheet on Page 3 for a better idea of where to place your device or
whether or not your chosen location will be in range.
Z-Wave Range Estimator.
Please use the below information to determine the depreciation of the Z-Wave
signal. Z-Wave devices should have a distance of approximately 100m (328ft)
without any obstacles in the way. Using the below information, if a signal has
to travel through an inner wall, it will lose approximately 40% of its signal.
Therefore, 100m multiplied by (100% – 40%) = 60m (197ft). Do this for every
wall, window, etc and you will have your approximation. There’s a worksheet on
Page 3 that will help. As always, this is just an estimate. Depending on the
manufacturer’s quality for your other Z-Wave products, your signal may vary.
Material | Thickness | Signal Depreciation |
---|---|---|
Aerated Concrete Stone | < 30cm // 11.8″ | 20% |
Aluminum Coating | < lmm // 0.04″ | 100% |
Ceiling | < 30cm // 11.8″ | 70% |
Furniture (non-wood) | < 30cm // 11.8″ | 40-60% |
Glass (w/out metal coating) | < 5cm 1/ 2.0″ | 10% |
Inner Wall | < 30cm H 11.8″ | 40% |
Iron Reinforced Concrete | < 30cm H 11.8″ | 30-90 % |
Material | Thickness | Signal Depreciation |
--- | --- | --- |
Metal Grid | < 1 mm 1/ 0.04″ | 90 0/0 |
Outer Wall | < 30cm H 11.8″ | 60% |
Plaster | < 10cm H 3.9″ | 10% |
Pumice | < 30cm // 11.8″ | 10% |
Red Brick | < 30cm H 11.8″ | 35% |
Stone | < 30cm H 11.8″ | 30% |
Wood | < 30cm // 11.8″ | 40-60 % |
Getting to Know Your LZW45 Lightstrip
Now that you’re familiar with Z-Wave and how it works, it’s time to understand
the basics of your new smart device. For more advanced configurations, please
see Pages 8-10. A. Config Button (and Scene Control): This button can be used
for various functions as shown in the table to the right. It can also be used
to trigger a Z-Wave scene. The scene is triggered when this button is pressed
one time.
B. Level Up Button (and Scene Control): This button can be used to increase
the level on your lightstrip. Press (hold) up to increase brightness. It can
also be used to trigger a Z-Wave scene. It supports up to 7 scenes (Tap 1x,
2x, 3x, 4x, 5x, Hold, Release).
C. Level Down Button (and Scene Control): This button can be used to decrease
the level on your light strip. Press (hold) down to decrease brightness. It
can also be used to trigger a Z-Wave scene. It supports up to
7 scenes (Tap 1x, 2x, 3x, 4x, 5x, Hold, Release).
D. Digital Display: The display is used for several different functions during
the operation of your light strips. In local config mode, it will display the
configuration parameter you are editing and the value. In normal operation, it
will show the level that the light strips are at. When your controller is
running an effect (flashing, pulsing etc.), the display will flash alternating
symbols.
Note: there is a 5-second time-out for the display. Five seconds after it
has displayed the current status, it will turn off as to not bother the user.
E. DC Power Connector: This is where you plug in the included 12V power
supply. The rating of the power supply is 12V DC 2.0A.
NOT SHOWN
F. Power Supply: 12V Power Supply to be used with the LZW45 controller.
G. Lights trips: These are theft or 6in light strips to be used with the
controller. The a number of strips may vary based on the configuration you
have purchased.
H. Connectors and End Cap: These are the various connectors that can be used
to make right angle or T connections with your strips. There is also an end
cap that needs
to be placed at the end of your connected strips. The number and type of
connectors included may vary based on the configuration you have purchased.
I. Accessories: This includes extension wires, mounting hardware, etc. Based
on the package you have purchased, the included accessories may differ.
NOTE: There are many “Pixel” effects included in the controller. In order
for the controller to run these effects correctly, there needs to be an end
cap at the end of your connected strips. This is so that the controller can
determine how many as well as the configuration of the strips it has connected
to it.
Energy Monitoring and Scene Control* are built-in features of this switch as
well.
* Please make sure your HUB supports these features. See the website for
more details.
Installing and Including (Pairing) Your Lightstrip Controller: General
Instructions Below are step-by-step instructions on how to install and pair
your lightstrip controller / light strips. For hub-specific instructions,
please use the QR codes or urls on Page 1.
Step 1: Gather Your Materials, Find an Appropriate Location, and Install
the Strips
- Locate an area to install your lightstrip within the recommended distance (Pages 3-4) from your HUB/Gateway.
- Walls, furniture, and other obstructions may degrade the communication between the device and your HUB/Gateway, so please keep this in mind when selecting a location.
NOTE: If you’d like to verify if the device is within range of your Z-Wave hub before installing it, feel free to use the Z-Wave range test which is a feature of the controller. Once the controller has started up, hold down the config button (A) for 5 seconds and the LED strip will turn green. Release the button and if the strip remains Green, then the device is within Z-Wave range. If the strips turn Red, then the device is not within range.
Step 2: Installing the Lightstrip Controller
Materials Needed: Screwdriver (if screw mounting the controller). Power outlet
to plug in the controller.
- Find the location where you would like the light strips to be installed and try to find a conspicuous place to install the controller. The length of the wire from the controller is only a few inches. If more length is required, use the optional extension wire that is available on our website.
- Decide whether you would like to secure the controller and whether you want to use the mounting screws or double-sided sticky tape to hold it in place.
- If you are using double-sided sticky tape, make sure the surface and the controller are clean and dry. Place the double-sided tape on the controller and adhere it to the desired location.
- If you are using the mounting screw, determine if you will need to use the included drywall anchor or not. If yes, drill a hole slightly smaller than the diameter of the wall anchor and press the drywall anchor into the hole.
- Screw the included screw either into the drywall anchor or into the wall (with a wood stud behind it).
- Place the back of the controller onto the screw head and slide downwards to secure the controller to its desired location.
Step 3: Installing the Lights trips
Materials Needed: Cleaning cloth and water.
- Before installing the strips to their desired location, make sure that the surface is clean and dry so that a good adhesion can be made.
- Plan out the length of the strip as well as any right angle, T-angle, or other adapters that are to be used.
- Determine the location that each strip piece needs to go and prepare to place them in that location.
- After the above steps are complete, remove the protective covering from the back of the light strips to reveal the double-sided sticky tape.
- Carefully align the first part of the lightstrip to the desired location and firmly press it against the surface that it is to be attached to.
- Continue to press each part of the lightstrip until you reach the end.
Step 4: Including the Controller Into Your Z-Wave Network
-
These are generic instructions. For hub specific instructions please use the QR codes or links on Page
1.Also, our knowledge base is a great location to find additional information on this device. It can be located at https://kb.inovelli.com. -
First, place your controller into pairing mode.
-
Next, triple press the config button (A) on the controller. If successful the lightstrip will start to blink blue.
-
If your controller supports S2 security, you may need to scan the QR code located on the controller or an insert that was included in the box. If scanning the QR code is not supported, you may also manually enter the 5 digit code that is included with the QR code.
-
If the inclusion is successful the lightstrip will turn green. If it turns red, the lightstrip was not included and you will need to try again.
Having Problems Including? Try an Exclusion
Place your hub or gateway into exclusion mode. Then: Press Button A 3x. If it
is successful the lightstrip will blink green. Then, try including again.
Device Parameters
Below you’ll find the various parameters associated with your device. There
are a ton of options for customization and as you can imagine, it’s hard to
write out all the possibilities in a manual. Please use this as a guide, but
also feel free to check out our site where we’ll give some specific examples
using each parameter.
Param
| Change at
the
controller?| Name| Description| Size| Range| Default
---|---|---|---|---|---|---
1| Yes| 1 :Of Pixels| When individually addressableLEDsat usedthisparameter
tells the controller the number of pixelsthat are attached. 0 -Autanatic
recognition of pixels. 1.130- Manually set the number of pixels.| 1| 0-30| 0
2| Yes| 2 Darning Speed| This changes the speed elwhich the bghtstrip drns up
a down. A setti-ig of 0 should turn the light immediately war off (almost like
anon/off switch). Increasing the value should slow down the transition speed.
0 – Instant Fast.. 98 – Slow| I| 0-98| 3
3| Yes| 3 Ramp Rate| This changes the speed rowlich the lightstrip turns on a
off. For example. when a user sends the switch a basicSet(vaue OxFF) or
basicSet(value: Ox00). this is the speed in with those actions take place
Asettingof 0 should turn the bght immediately on or off (almost like anon/off
switch). Increasing the value show slowdown the transition speed. A setting of
99 should keep this in sync with parameter 2.0 – Instant.1- Fast.. 98 – Slow.
99 – Keep el sync with parameter 2| I| 0-99| 99
4| Yes| 4 Minknum Level| The minimum level that the strip can be dimmed to.
Useful when the user has an LED strip that does not to m on or f tickers at a
lower level.| 1| 1-45| 1
5| Yes| 5 Maximum Level| The maximum level that the stripcal be dimmed to.
Useful when the user has an LED strip that reaches its maximum level before
the miler valued 99.| 1| 55-99| 99
6| No| 6 No Auto Off Trier| Automatically ams the strip off after this many
seconds. When the strip is timed on a timer is started that is the citation of
this setting. When the timer expires. the strip is turned oft 0 – Auto off is
disabled| 2| 0-32767| 0
7| Yes|
7 Default Level
(Local)
| The default level for the strip when it is powered on from the local switch.
A sett.); of 0 means that the switch will return to the level that it was on
before it was timed off. 0 – Previous| 1| 0-99| 0
8| Yes| 8 Default Level (Z-
Wave)| The default level for the corner when it is powered on from a
Z-Wavecanmand 0.e. BasicSet(off). A setting of 0 means that the switch will
return to the level that it was on before it was turned oft 0- Previous| 1|
0-99| 0
9| No| 9 No Default Color| Byte(3-2): Values between 2700-6500 represent a car
temperature. Byte(1-0): Values between 1-360 represent the color on the Noe
color wheel. The value of 361 represents a random color and a value of 0
represents the previous cola.| 4| 0-6500| 0
10| Yes| 10 Yes State after power
Restored| The state the switch should rearn to once power is restored after
power failure. 0- Off. 1 – Der aid Color / Level (Parameter 9). 2 – Previous|
1| 0-2| 2
17| No| 17 No Active Power
Reports| The power level change that will result in anew power report being
sent. The value is a percentage of the previous report. 0 = disabled| 1|
0-100| 10
18| No| 18 No Periodic Power 8
Energy Reports| Trne period between calsectrtive power 8 energy reports being
sent (in seconds). The trner is reset after each report is sent.| 2| 0-32767|
3600
19| No| 19 No Active Energy
Reports| Energy reports Energy level change which wil result in sending a new
energy report. Avail- able settings 0- energy reports disabled 1-127(0.01-127
kWh) – report triggering threshold. Default settilg:10 (0.1 kWh)| 1| 0-100| 10
21| No| 21 No Quick Strip Effect| Turn cn a quick effect that is similar to
the LED notifications on our dimmers and switches. See the website for
details.| 4| 0-
2147483647| 0
22| No| 22 No Custom Effect
Parameter 1| A custom effect with tsp to 4 acbons can be taned on with correct
iipit for parameters 22-24.30. This parameter controls the color and
transition of those actions See website for details.| 4| 0-
2147483647| 0
23| No| 23 No Custom Effect
Parameter 2| A custom effect with up too actions can be turned on with correct
iipit for parameters 22- 24.30. This parameter controls the level of those
actions. See the website for details.| 4| 0-
2147483647| 0
24| No| Custom Effect| A custom effect with up to 4 actions can be turned on
with correct input for parameters 22-| 4| 0-| 0
---|---|---|---|---|---|---
| | Parameter 3| 24, 30. This parameter controls the duration of those
actions. See website for details.| | 2147483647|
30| No| Custom Effect| A custom effect with up to 4 actions can be turned on
with correct input for parameters 22-| 4| 0-32768| 0
| | Parameter 4| 24, 30. This parameter controls the number of iterations, the
end effect, and the scale of the duration in parameter 24. See website for
details.| | |
31| No| Pixel Effect| Turn on an effect that utilizes the individually
addressable LEDs. Listed Below.| 2| 0-32767| 0
| | | Byte 0 = Effect, Byte 1= Level| | |
51| No| Disable Physical| The 700ms delay that occurs after pressing the
physical button to turn the switch on/off is| 1| [1:No (De-| 1
| | On/Off Delay| removed. Consequently this also removes the following
scenes: 2x, 3x, 4x, 5x tap. Still work- ing are the lx tap, held, released,
and the level up/down scenes.| | fault), 0:Yes]|
Pixel Effects
At release, the controller has around 50 effects that utilize the ability of the controller to control each individual LED. These effects allow you to really show off the capabilities of this device and dazzle your friends and neighbors. Listed below are some of the effects that are available. Describing them in this manual would take up too much room, but see below for some of their names. To try them out you need to set parameter 31. 31 is the effect number and the brightness that you would like the strip to have.
1. Static
2. Blink
3. Breath
4. Color Wipe
5. Color Wipe
Reverse Inverse
6. Color Wipe
Random
7. Random Color| 8. Single Dynamic
9. Multi Dynamic
10. Rainbow
11. Rainbow Cycle
12. Scan
13. Dual Scan
14. Fade
15. Running Lights
16. Twinkle| 17. Twinkle Random
18. Twinkle Fade
19. Twinkle Fade
Random
20. Sparkle
2. Flash Sparkle
22. Hyper Sparkle
23. Strobe
24. Blink Rainbow| 25. Chase White
26. Chase Color
27. Chase Random
28. Chase Rainbow
29. Chase Flash
30. Chase Flash
Random
3. Chase Rainbow
White| 32. Chase Blackout
33. Chase Blackout
Rainbow
34. Color Sweep
Random
35. Running Color
36. Running Red
Blue
37. Running| Random
38. Larson Scanner
39. Comet
40. Fireworks
41. Fireworks
Random
42. Merry Christmas
43. Circus
Combustus
44. Halloween
45. Aurora
More to come!
---|---|---|---|---|---
Resetting Your Device
You may hold the Config Button (A) for 20 seconds or use a certified
controller to remove the device from your network to factory default. Only
use this procedure in the event that the network primary controller is missing
or otherwise inoperable.
OTA Note
Over-the-Air updates are available on this device. It will take about 1 minute
after completion for it to, “settle”, so please leave the device alone
for a minute after flashing.
If the power is cut off immediately after OTA is completed, OTA may fail.
Local Configuration Mode
There are a couple different ways you can set the configuration parameters of
your device (listed on page 7 & 8). It is recommended that you
set them from your hub when possible, but if not, you can set them directly
from the device! For more detailed instructions, please check our
support web page at support.inovelli.com. Here are some basic instructions:
- Enter into configuration mode by holding down the configuration button (A) for 10 seconds.
- Press the configuration button (A) the number of times that corresponds with the parameter number you want to change (listed on page 7 & 8).
- Use the level up/down (B & C) buttons to set the parameter to the value you would like. Each press increments the value by 1.
- You will see the value of the parameter on the controller’s display. This gives you instant feedback of the value you are going to set the parameter to.
- After you are finished, press and hold JUST the A button for 10 seconds to save and exit. While holding the button the LED strip will first turn green. At this point keep holding the button. After 5 more seconds the strip will turn yellow. Release the button at this point and you will see “SUC” on the display and the LED strip will flash cyan.
Command Class Information
Command Class| Version| Not added| Non-
Secure
added| Securely Non-se-
cure CC| added Secure
CC
---|---|---|---|---|---
Z-WAVE PLUS INFO| 2| X| X| X|
TRANSPORT SERVICE| 2| X| X| X|
SECURITY 0| 1| X| X| X|
SECURITY 2| 1| X| X| X|
SUPERVISION| 1| | X| X|
APPLICATION STATUS| 1| | X| X|
SWITCH MULTILEVEL| 4| | X| | X
CONFIGURATION| 4| | X| | X
ASSOCIATION| 2| | X| | X
ASSOCIATION GRP INFO| 3| | X| | X
VERSION| 3| | X| | X
MANUFACTURER-SPECIFIC| 2| | X| | X
DEVICE RESET LOCALLY| 1| | X| | X
POWERLEVEL| 1| | X| | X
SWITCH COLOR| 3| | X| | X
SWITCH BINARY| 1| | X| | X
PROTECTION| 2| | X| | X
FIRMWARE UPDATE MD| 5| | X| | X
METER| 3| | X| | X
CENTRAL SCENE| 3| | X| | X
BASIC| 2| | X| | X
INDICATOR| 3| | X| | X
MULTI-CHANNEL ASSOCIATION| 3| | X| | X
MULTI-CHANNEL| 4| | X| | X
Z-Wave Association Groups
Group # | Max Nodes | Commands |
---|---|---|
Group 1 | 5 | 1. Central Scene |
2. Basic Report
3. Multilevel Report
4. Protection Report
5. Device Reset Locally
6. Meter Report
Group 2| 5| Basic Set
Group 3| 5| Switch Multilevel Set
Group 4| 5| Switch Multilevel Set
Group 1: Lifeline — Members of this group will receive unsolicited messages
related to the status of the switch.
Group 2: Basic Set — Sends On & Off commands to associated devices. (1. Single
press UP button sends BasicSet (0xFF) and 2. Single press Down sends BasicSet
(0x00)
Group 3: Switch Multilevel Set — Sends set level commands to associated
devices when the up/down button is pressed.
(1. Hold & Release Up or Down button sends SwitchMultiLevelSet which keeps
associated devices in sync with this device. 2. Single press Up button sends
SwitchMultiLevelSet(0xFF) and 4. Single press Down button sends SwitchMultiLev
elSet(0x00)
Group 4: Switch Multilevel Set — Sends start / stop level change to associated
devices.
(1. Hold Up button sends SW_MULTILEVEL_START_LEVEL_CHANGE (Up)
2: Hold Down button sends SW_MULTILEVEL_START_LEVEL_CHANGE (Down) 3.
Release Either button sends SW_MULTILEVEL_STOP_LEVEL_CHANGE
Federal Communications Commission (FCC) Statement
FCC Caution:
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2)This device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: —Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver. —Connect the
equipment into an outlet on a circuit different from that to which the
receiver is connected. —Consult the dealer or an experienced radio/TV
technician for help. Attention FCC:
Device Warranty
Warranty: Inovelli will replace any defective unit for one year after the date
of purchase pending the unit was used in the manner it was intended to. Please
email us
at: contact@inovelli.com or visit us at
www.inovelli.com/warranty for full
details.
Project Cribs
This is the second project that we have teamed up with the community on to help visualize, develop, and beta test it. Having a group of enthusiastic smart home users to guide this project to completion has been invaluable. They have been a true pleasure to work with and this product would not be nearly what it is without them. Thanks to the beta testers for all their hard work – we couldn’t do it without you!
| I
remember exactly where I was when this idea first came to life. Nathan and I
were at the manufacturer eating breakfast and I remember seeing the beautiful
lightstrips that they had shown us and we thought, “what if we took those
lightstrips and cut them into 1ft sections so that there wouldn’t be any waste
and people could use the sections elsewhere if need be?” Then, we started
thinking about use cases and introduced the T and L-shaped accessories so you
could work around corners. Adding the addressable LED’s was the final touch
and we couldn’t be more proud.
---|---
| As mentioned in the project description, Project Cribs has been a long time
in the making. Our second Z-Wave 700 product truly stands out from the rest.
Addressable LEDs, customizable effects, easily connectable lightstrip sections
to name a few of the stand out features. In addition, we have included scenes,
energy & power reporting, and all the other advanced features our customers
have come to expect. It truly has been a wild ride, but it has been worth it!
| The
lightstrip is going to be huge for the smart home industry. The part I’m most
excited about is the
customizable effects, pixel effects, and all the other bells and whistles that
come with this device. The fact that we had an entire group of community beta
testers testing this has been amazing.
| The
Lightstrip continues to be one of my favorite projects to work on. The
advanced features and just all-around sweetness has pushed us even further in
design, packaging, and overall marketing strategy. I’m excited to see the
custom spaces that get created in our community as they always know how to
push our products even further.
|
Project Cribs! What a wild ride. Between postponements, tariff issues,
conflicting demand, pricing
issues – you name it – we’re finally here! This has been such a fun project to
work on. I remember
introducing it at CES 2020 and people were going crazy for it! It’s the first
of it’s kind for Z-Wave –
individually addressable LED’s, chase scenes – it’s fun stuff! We all had a
blast working on this project
and we can’t wait to use it in our own homes and to see pictures of everyone
else using it in theirs!
Device Specifications
Input Voltage (V) | 100-240V AC |
---|---|
Input Frequency (Hz) | 50/60 |
Output Voltage (V) | 12V DC |
Output Current (A) | 2 |
Luminous Flum(Im) | 1600(@4000K 20W) |
CCT (K) | 2700K-6500K |
Power(W) | 20W |
DF | 0.5 |
Stand-by power Consumption(W) | <1.5 |
--- | --- |
Start up Times(s) | <0.5 |
Beam angle (°) | 120° |
Color Rendering Endex | >80 |
Color Rolenance Adjustment (SDCM) | <6@2200K 4000K |
Stroboscopic requirements | Yes |
Lift time (H) | 25000 |
Dimensional requirement/mm | 3250’44’75 |
Certification requirement | FCC+Zave+ETC |
--- | --- |
Control distance (m) | 30(Indoor open field) |
Dimming range | 5%~100% |
Operating temperature (°) | 0°C~40°C |
Maximum RF Power (dBm) | -1.5dBm |
Frequency Band | 908.4-916 MHz |
The length can be extended | Up to 30.48*16 cm |
ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada
licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation of the device.
www.inovelli.com/lzw45/setup
contact@inovelli.com
References
- inovelli.com/lzw45/setup/hassio
- inovelli.com/lzw45/setup/hubitat
- inovelli.com/lzw45/setup/other
- inovelli.com/lzw45/setup/smartthings
- support.inovelli.com
- inovelli.com/lzw45/setup
- kb.inovelli.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>