Meissalivve 20240228 TV Stands for TVs up to 8 Inch Media Console User Manual

Meissalivve 20240228 TV Stands for TVs up to 8 Inch Media Console

PLEASE DO NOT RETURN TO STORE

STOP
Please do not return this product to the retailer!!We are able to assist you in ANY way
If you find that you have any trouble with assembly or missing or damaged parts please contact the seller.

Safety and Care Advice

Important – Please read these instructions fully before starting assembly

• Check you have all the components and tools listed on the following pages.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Make sure you have enough space to layout the parts before starting.
• During assembly do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor.
• Parts of the assembly will be easier with 2 people.
• To reduce the likelihood of damaging your product please ensure that your power drill is set on a low torque setting.

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Handy Hints

• Assemble all parts and bolts loosely during assembly, only once the product is complete should you fully tighten the bolts
• Regularly check and ensure That all bolts and fittings are tightend properly.

WARNING
In order to help prevent overturning – please follow these instructions

To help prevent product toppling over please follow the below steps:-

• Use the anti tip stap or wall fixing method provided (if applicable)
• Do not allow children to climb or hang on the furniture
• Do not open more than one drawer at a time
• Do not place heavy items in the top drawers
• Do not place heavy items on top of the furniture, unless the furniture has been designed for this purpose

Before Installation

Important – Please read these instructions fully before starting assembly
Thank you for purchasing this quality product. Be sure to check all packing materials carefully for small parts, which may have come loose inside the carton during shipment. Identify and count all items according to the PARTS LIST and/or HARDWARE LIST shown below. Check you have all the components and tools listed on the following pages.

• We recommend that you assemble this product with the assistance of another person; this will make the assembly easier, and will help eliminate damage to the product or injury to persons during assembly.
• Please do not over tighten screws or bolts until the assembly is completed.
• Keep children and animal away from the work area, small parts could choke if swallowed.
• Please put all parts on a non-abrasive floor before assembly,and follow the assembly steps to assemble your newly purchased product correctly and efficently.

Cam Lock Assembly Instructions

Using Camlocks

HINGE ADJUSTMENTS

• 1 Sideways / Tilt adjustment
  Turn the screw
  clockwise to move the door further away from the side of the cabinet anticlockwise to move the door closer to the side of the cabinet

• 2  4   Height adjustment
  While supporting the weight of the door, turn the screws clockwise to move the door up anticlockwise to move the door down

• 3 Forward and back adjustment
  If the gap between the back of the door and the cabinet is too small, and the door may not close fully. Turn the screw clockwise to decrease the gap between the door and the cabinet anticlockwise to increase the gap between the door and the cabinet

Components -Fittings

PLEASE NOTE : Part number 10 Part number 11 are covered with a tight plastic protective film.
If there are scratches on the product after disassembly, please don’t worry, it’s not product damage. Please slowly tear off the protective plastic film on the surface along the edge. After peeling off, the product becomes smooth and clean.

Assembly Instructions

Step 23
PLEASE NOTE : Part number 10 Part number 11 are covered with a tight plastic protective film.
If there are scratches on the product after disassembly, please don’t worry, it’s not product damage. Please slowly tear off the protective plastic film on the surface along the edge. After peeling off, the product becomes smooth and clean.

LED Light

How to fix LED strip lights not working:

1. Make sure the arrows on the female and male connector are aligned.
2. Make sure the plastic inserted into the remote control is removed before using it.
3. The remote control only works within a certain range only. Don’t use the remote control from a faraway distance.
4. Point the remote control at the receiver, not the light strip.

Note: These two buttons are invalid because this product cannot adjust the brightness of the light.

Note: The remote control is compatible with CR2025 battery. Battery is NOT included in the package to comply with safety regulations in certain shipping conditions.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>