SW-MOTECH GPT.06.564.30000 Rackpack Set for Yamaha Instruction Manual
- June 8, 2024
- SW-MOTECH
Table of Contents
GPT.06.564.30000 Rackpack Set for Yamaha
Instruction Manual
GPT.06.564.16000/B
GPT.00.152.54500/B
BC.HTA.00.305.30000
Item No.: GPT.06.564.16000/B
Revision: 00
Date: 01- 2018
STREET -RACK
Thank you for choosing this premium product from SW-MOTECH. Please visit our
webshop for additional information, such as application charts and PDF
mounting instructions. Any other documents that may be required le.g. ABE
certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical
understanding! For your own safety SW-MOTECH recommends having installation
and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no
liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay
attention to all relevant information in the vehicle manual during assembly.
Nonconformance can lead to vehicle damage or even endanger the driver! These
mounting instructions are written based on our current state of knowledge.
Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting.
Compatibility with original accessory parts or other manufacturers’ accessory
parts is not guaranteed. Furthermore, BEFORE installing this product, make
sure that all moving parts (e.g. the chain) are in the original state of
maintenance. Installed accessories can change the driving behaviour and/or
stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle
registration/operation as well as TOV regulations if applicable. If required,
register installed parts in the vehicle documents through an appropriate
inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that
all items of the parts list are included. Make sure that your vehicle is
parked safely and cannot fall over. Turn off the engine and remove the
ignition key. Let the motor/exhaust cool off if necessary. Disconnect the
vehicle battery when working on the electrical system. Use appropriate tools.
Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be
reinstalled in accordance with the vehicle manufacturers’ specifications or
replaced by parts delivered by SW- MOTECH. Secure all threads, unless
otherwise specified, with medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTECH must be obtained from the
vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and
connections previously removed are property replaced. Also make sure that no
moving parts are obstructed and no function of the vehicle is hindered in any
way. Cables and hoses must not rub and/or be pinched. Before starting to ride,
perform a comprehensive check of all functions. After the first 50 km and then
at regular intervals, check the tightening torque of all screw connections and
the proper fit of the product.
PRODUCT SPECIFIC INFORMATION
| Maximum Load | Maximum Speed |
|---|---|
| 5 KG (11 ibs) |
ATTENTION: The indicated maximum load is inclusive the weight o topcase/luggage and adapter plate! The maximum vehicle load specified by the manufacturer must not be exceeded!
Packed by: ————————-
Gate of packaging: ——————-
SW-MOTECH GmbH & Co. KG
Ernteweg 8/10
35282 Rauschenberg Germany
Phone + 49 (0)6425 / 8168 – 050
Fax + 49 10)6425 / 8168 – 10
info@sw-motech.com
www.sw-motech.com
PART LIST
Step| No| Item.No/Discription| Part| Quantity**|
**N.m
---|---|---|---|---|---
1| 1| GPT.06.564.002L/R| Mounting Bracket; left / right| 2/2|
2| M8 x 35; ISO 7380| Lenshead Screw; black| 2/2| 23
3| Ø 20/Ø 8,2/h 4| Spacer| 2/2|
4| M8 x 45; ISO 7380| Lenshead Screw; black| 2/2| 23
5| Ø 20 /Ø 8,4/19| Spacer| 2/2|
6| Ø 20/Ø 8,4/14| Spacer| 2/2|
2| 7| GPT.00.564.050| Luggage Rack| 1/1|
8| M8 x 30; DIN 7991| Countersunk Screw; black| 4/4| 23
9| d 8,4| Countersunk Washer; black| 4/4|
10| M8; DIN 6927| Lock Nut with Flange; black| 4/4|
8.8| Coarsed Thread| Ø| M4| M5| M6| M8|
M10| M12
---|---|---|---|---|---|---|---|---
Steel CL 8.8| N-m| 2,8| 5,5| 9,6| 23| 46| 79
10.9| Coarsed Thread| Ø| M4| M5| M6| M8|
M10| M12
---|---|---|---|---|---|---|---|---
Steel CL 10.9| N-m| 4,1| 8,1| 14| 34| 67| 115
- All measurements in millimeters.
** The second number indicates the total quantity of the part in the delivery.
*** No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.
Mounting
NOTE: In order to mount the luggage rack in combination with the original
accessory soft side bag stay, use the spacers 161, as shown in the detail
drawing.
Remove the screws from the shown mounting points.
Attach the mounting brackets (1) to the vehicle, as shown in the drawing.
ATTENTION: Use liquid thread locker!
Tighten the screws as specified in the parts list.
Attach the luggage rack (71 to the mounting brackets (1). Tighten the screws as specified in the parts list.
Item No.: CP7.00.152.54500/8
Revision: 00
Date: 03 – 2018
Luggage rack extension for STREET-RACK
Thank you for choosing this premium product from SW-MOTECH. Please visit our
webshop for additional information, such as application charts and PDF
mounting instructions. Any other documents that may be required !e.g. ABE
certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical
understanding! For your own safety SW-MOTECH recommends having installation
and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no
liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay
attention to all relevant information in the vehicle manual during assembly.
Nonconformance can lead to vehicle damage or even endanger the driver! These
mounting instructions are written based on our current state of knowledge.
Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting.
Compatibility with original accessory parts or other manufacturers’ accessory
parts is not guaranteed. Furthermore, BEFORE installing this product, make
sure that all moving parts (e.g. the chain) are in the original state of
maintenance. Installed accessories can change the driving behaviour and/or
stability of your vehicle.
GENERAL INFORMATION
Observe the country:specific regulations concerning vehicle
registration/operation as well as TUV regulations if applicable. If required,
register installed parts in the vehicle documents through an appropriate
inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that
all items of the parts list are included. Make sure that your vehicle is
parked safely and cannot fall over. Turn off the engine and remove the
ignition key. Let the motor/exhaust cool off if necessary. Disconnect the
vehicle battery when working on the electrical system. Use appropriate tools.
Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be
reinstalled in accordance with the vehicle manufacturers’ specifications or
replaced by parts delivered by SW- MOTECH. Secure all threads, unless
otherwise specified, with medium-strength liquid thread locker. Torque
specifications undefined by SW-MOTECH must be obtained from the vehicle
manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and
connections previously removed are properly replaced. Also make sure that no
moving parts are obstructed and no function of the vehicle is hindered in any
way. Cables and hoses must not rub and/or be pinched. Before starting to ride,
perform a comprehensive check of all functions. After the first 50 km and then
at regular intervals, check the tightening torque of all screw connections and
the proper fit of the product.
Packed by: ————————-
Gate of packaging: ——————-
SW-MOTECH GmbH & Co. KG
Ernteweg 8/10
35282 Rauschenberg Germany
Phone + 49 (0)6425 / 8168 – 050
Fax + 49 10)6425 / 8168 – 10
info@sw-motech.com
www.sw-motech.com
PART LIST
Step| No| item.No/Discription| Part| Quantity**|
**N.m
---|---|---|---|---|---
| 1| GPT.00.152.502| Adapter Plate| 1/1|
2| GPT.00.152.048| Luggage Rack Extension| 1/1|
3| M6 x 14; ISO 7380| Lenshead Screw; black| 4/4|
4| M6; DIN 985| Lock Nut| 4/4|
8.8| Coarsed Thread| Ø| M4| M5| M6| M8|
M10| M12
---|---|---|---|---|---|---|---|---
Steel CL 8.8| N-m| 2,8| 5,5| 9,6| 23| 46| 79
10.9| Coarsed Thread| Ø| M4| M5| M6| M8|
M10| M12
---|---|---|---|---|---|---|---|---
Steel CL 10.9| N-m| 4,1| 8,1| 14| 34| 67| 115
- All measurements in millimeters.
** The second number indicates the total quantity of the part in the delivery.
*** No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.
Mounting
Adapter plate for STREET-RACK
Attach the shown parts to the adapter plate for STREET-RACK (1). Tighten the
screws as specified in the parts list.
Mounting the adapter plate on the STREET-RACK.
Step [1]: Slide the adapter plate (1) with the two hooks into the holes
of your STREET-RACK (sold separately).
Step [2]: Press the adapter plate (1) slightly downwards and turn the
fastener 90 degrees until it fits into place.
Step [3]: Finally, press the lock firmly down as shown in the
drawing.
To release the adapter plate, simply pull the fastener upwards and turn
it to the starting position.
Mounting Instructions
Item No.: BC.HTA.00.305.3000
Revision: 00
Date: 09 – 2020
PRO Rackpack tail bag
Thank you for choosing this premium product from SW-MOTECH. Please visit our
webshop for additional information, such as application charts and PDF
mounting instructions. Any other documents that may be required (e.g. ABE
certifications), are also available for download at our webshop. Installation
and/or maintenance of this product require good technical understanding! For
your own safety SW-MOTECH recommends having installation and/or servicing
carried out by a specialist workshop! SW-MOTECH assumes no liability for
damage caused by improper installation and/or maintenance work! Carefully
follow all the directions given in the mounting instructions and pay attention
to all relevant information in the vehicle manual during assembly. Non
conformance can lead to vehicle damage or even endanger the driver! These
mounting instructions are written based on our current state of knowledge.
Legal requirements for accuracy do not exist. This product was developed for
vehicles in their factory setting. Compatibility with original accessory parts
or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE
installing this product, make sure that all moving parts (e.g. the chain) are
in the original state of maintenance. Installed accessories can change the
driving behaviour and/or stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/
operation as well as TUV regulations if applicable. If required, register
installed parts in the vehicle documents through an appropriate inspection
authority.
PREPARATION: Read the mounting instructions carefully and make sure that
all items of the parts list are included. Make sure that your vehicle is
parked safely and cannot fall over. Turn off the engine and remove the
ignition key. Let the motor/exhaust cool off if necessary. Disconnect the
vehicle battery when working on the electrical system. Use appropriate tools.
Have another person to help you.
FUNCTION CHECK: This is a universal product. For this reason make sure
BEFORE the first use, that the product can be fixed property and used without
problems with your vehicle type. After fixation also make sure that no moving
parts are obstructed and the function of the vehicle is not hindered in any
way. Lamps as taillight and turn signals must not be limited in their
function. Cables and hoses must not rub and/or be pinched. Before starting to
ride, perform a comprehensive check of all functions. All components of the
product must not contact any hot or moving parts of the vehicle. All parts
should also remain 5 cm away from hot parts of the vehicle and remain clear of
the exhaust stream. For this reason compress the suspension fully several
times with your vehicle stationary.
ATTENTION: Before riding and at each stop (every 200 km1 check proper
fixation of the product!
PRODUCT SPECIFIC INFORMATION
ATTENTION: Riding with this product may affect the motorcycles driving and
braking performance! Cornering and ground clearance can be reduced by using
this product!
ATTENTION: Modifications will void any warranty.
| Maximum Load | Maximum Speed |
|---|---|
| 10 KG (22 ibs) |
ATTENTION: The maximum vehicle load specified by the manufacturer must not be exceeded!
| Maximum Load | Maximum Speed |
|---|---|
| 5 KG (11 ibs) |
ATTENTION: The maximum vehicle load specified by the manufacturer must
not be exceeded!
ATTENTION:
NOT FOR OFFROAD-USE
Packed by: ————————-
Gate of packaging: ——————-
SW-MOTECH GmbH & Co. KG
Ernteweg 7/10
35282 Rauschenberg Germany
Phone + 49 (0)6425 / 8168 – 050
Fax + 49 10)6425 / 8168 – 10
info@sw-motech.com
www.sw-motech.com
Step| No| item.No/Discription| Part| Quantity**|
**N.m
---|---|---|---|---|---
| 1| BC.ZUB.00.122.30000| Tail Bag| ¹⁄¹|
2| BC.ZUB.00.041.30000| Waterproof I nnerbag| ¹⁄¹|
3| BC.ZUB.00.128.30000| Shoulder Strap| ¹⁄¹|
4| BC.ZUB.00.120.30000| Loop Strap Set; 4 pieces| ¹⁄¹|
5| LSF.350.250| Velcro Strap Set; loop side; 2 pieces| ¹⁄¹|
6| BC.ZUB.00.121.30000| Velcro Strap Set; hook side; 2 pieces| ¹⁄¹|
8.8| Coarsed Thread| Ø| M4| M5| M6| M8|
M10| M12
---|---|---|---|---|---|---|---|---
Steel CL 8.8| N-m| 2,8| 5,5| 9,6| 23| 46| 79
10.9| Coarsed Thread| Ø| M4| M5| M6| M8|
M10| M12
---|---|---|---|---|---|---|---|---
Steel CL 10.9| N-m| 4,1| 8,1| 14| 34| 67| 115
Note: a All measurements in millimeters. b The second number indicates
the total quantity of the part in the delivery.
C No torque specifications: Use the torque defined by vehicle
manufacturer! The standard torque in this table can be used as long as it is
within the vehicle manufacturer’s specifications.
Copyright by
SW-MOTECH GmbH 8 Co. KG
Errors and omissions excepted. Technicat and design rnottilicetions are
subject to change.
FASTENING
The luggage rack extension and the vehicle are examples.
FIXED ON THE LUGGAGE RACK EXTENSION
Step [1]: Loop two loop straps 141 together.
Step 121: Guide the loop straps (4) through the shown openings of the
example luggage rack extension. Step la Hook the cam-hooks of the loop straps
141 onto the D-rings of the tail bag 111.
Step 141: Pull the loop straps 141 on all four cam-hooks tight.
Step [5]: Roll up the excess lengths of the loop straps (4) … Step [6]: …
and fix it with the velcro straps.
FASTENING TO THE LUGGAGE RACK
Step 111: Loop the velcro straps 161 and 17) onto the loop at the bottom
of the tail bag 111. Make sure that the loop and hook sides can be easily
attached. Place the tail bag (1) on the luggage rack.
Step [2]: Fasten the tail bag 111 to your luggage rack with the velcro
straps 161 and (7). Make sure that the tail bag (1) is fastened in such a way
that it cannot slip while driving.
OPTIONAL: The velcro strap sewn on the front can be looped around the
backrest to provide additional support.
Step [4]: Entangle the loop straps (41 to FOUR suitable and loadable
fastening points to the vehicle. as shown in the example illustrations [A] to
[C] (e.g. vehicles frame, footrest mounts, luggage hook etc.l.
ATTENTION: The fastening points must be chosen so that the tail bag (1)
is secured against slipping! To do this, tension the tail bag to the front at
the two front fastening points and to the rear at the two rear fastening
points!
Step 151: Hook the cam-hooks of the FOUR loop straps (4) onto the 0-rings
of the tail bag (1).
Step 161: Pull the loop straps 141 on all four cam-hooks tight until the
tail bag (1) is centered and securely fastened to the vehicle.
Step 171: Roll up the excess lengths of the loop straps (4) … Step … and
fix it with the velcro straps.
ATTENTION: All components of the tail bag must not contact any hot or
moving parts of the vehicle. All parts should also remain 5 cm away from hot
parts of the vehicle and remain clear of the exhaust stream.
ALL FASTENING POSSIBILITIES
ATTENTION: Before riding and at each stop (every 200 km) check the proper
fixation of the tail bag (1 l!
LOADING AND CARE
ATTENTION: Always use the included waterproof innerbag (21 to protect your luggage from moisture! Fasten the waterproof inner bag 12) to the velcro patch on the inside. Additionally protect sensitive luggage (e.g.. electronic equipment) from moisture with a plastic bag.
LOADING: Never store pointy or sharp-edged objects, which could cause injury to persons or damage to the vehicle/product! ONLY loop assigned SW- MOTECH products to the MOLLS attachment!
CARE: For cleaning use ONLY a soft textile brush, cloth or sponge and
warm soapy water! Rinse with clean water. Do NOT use strong cleaning agents,
rough cleaning tools or high pressure washer! Clean the product after riding
in salty conditions, to avoid damage from salt.
Copyright by
SW-MOTECH GmbH 8 Co. KG
Errors and omissions excepted. Technicat and design rnottilicetions are
subject to change.Lock Nut with Flange; bla241ck
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>