BRAINLIT VIDAR Surface Mounts and Pendants Instruction Manual

INSTALLATION INSTRUCTIONS VIDAR

VIDAR Surface Mounts and Pendants

The BCL™ System by BrainLit – an intelligent lighting solution mimicking natural daylight indoors for human wellbeing
VIDAR Mounting VIDAR comes in two different versions – surface mount and pendant

Surface installation

1. Install the bracket on the ceiling. Use screws and plugs suitable for your ceiling.
2. Connect metal wire between luminaire and bracket. Perform the electrical installation according to standards and regulations in your region, see “Electrical installation”.
3. Attach the luminaire to the bracket. Make sure that the pins fit in the holes of the bracket. Rotate the luminaire slightly to lock it in place.
4. Turn on the electricity and enjoy the new luminaire.

Suspended installation

1. Install the bracket on the ceiling. Use screws and plugs suitable for your ceiling.
2. Attach ceiling cup and luminaire to bracket. Adjust mounting height by pushing down the pin on the wire locks located on the luminaire body. Adjust length of electric cable and fasten the plastic cable locks.
3. Perform the electrical installation according to standards and regulations in your region, see “Electrical installation”.

Electrical installation
Disconnect power before installation, maintenance or service.
EU WAGO
Connect the WAGO connectors.

EU terminal
Connect the two DALI wires to push-in terminals CH1 and CH2 in the ceiling cup.
DALI is polarity insensitive. Connect neutral (N), line (L) and protective ground ( **** ) to their respective terminals.

Data

VIDAR DEEP DIM
Maximum circuit breaker  loading (no of luminaires): B10 B13 B16 C10 C13 C16 @230V 21 27 33 21 27 33
VIDAR
Maximum circuit breaker loading (no of luminaires): B10 B13 B16 C10 C13 C16 @230V 43 56 69 43 56 69

Ø600 mm
P/N: 100027 100042 (DEEP DIM)

Maximum suspension length: 2 m
Ø600 mm P/N: 100045

Warning

• Disconnect or turn power off before installation, maintenance or service.

• Installation requires knowledge of luminaire’s electrical systems.
  If not qualified, do not attempt installation. Contact aqualified electrician.

• Brainlit’s luminaires must be installed in compliance with international wiring regulations (EN, IEE, NEC etc.).

• Secure luminaire compatibilty with input voltage and frequency.

• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or sharp objects.

• Risk of fire or electric shock. Keep combustible and other inflammable materials away from lamp/lens.

• The luminaire is not suitable for covering with thermally insulating material.

• Do not operate in close proximity to persons, inflammable materials or substances affected by heat or dying.

• Wear gloves and safety glasses when removing luminaire from carton, installing, servicing or performing maintenance.

• Do not touch enclosure or light source.

• Allow lamp/luminaire to cool down before handling.

• The connecting cable is not waterproof.

• No user serviceable parts inside of luminaire.

• Luminaire to be independently supported to building structure.

• Avoid direct eye exposure to light source when luminaire is on.

This document contains information that is subject to change without notice. This document is solely intended for, and may only be used for, the purpose of providing luminaire products to the BrainLit BioCentric Lighting System. The performance indications for BrainLit products set forth in this document are based on, and conditioned on, the products being used solely in the BrainLit BioCentric Lighting System. However, this document shall not be deemed a product warranty, whether express or implied. The BrainLit product warranty is solely contained in the purchase agreement with each customer. This document is subject to BrainLit AB’s copyright. No part of this document may be reproduced or transmitted in any form or by any means, or shared with any third party, without the prior written approval of BrainLit AB. BrainLit products may be protected by one or more patents and by copyright and design rights. “BrainLit” and “BioCentric Lighting” are registered trade marks of BrainLit AB. This document does not confer upon the recipient a license to any of BrainLit intellectual property rights.

BrainLit AB, Scheelevägen 34,
223 63 Lund, Sweden
+46 46-37 26 00
info@brainlit.com
www.brainlit.comhttp://www.brainlit.com/vidar

References

• BrainLit • Lighting for health and wellbeing

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>