Velleman VDL8LS Lighting Bridge with 2x Extra T Bars User Manual

Velleman VDL8LS Lighting Bridge with 2x Extra T Bars

Introduction

To all residents of the European Union
Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized company for recycling. This device should be returned to your distributor or to a local recycling service. Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for choosing HQPower™! Please read the manual thoroughly before bringing this device into service.
If the device was damaged in transit, do not install or use it and contact your dealer.

Safety Instructions

• Keep this device away from children and unauthorized users.

• Refer to an authorized dealer for service and/or spare parts.

• This device is designed for professional use on stage, in discos, theatres, etc. The VDL8LS should only be
  used indoors.

• A qualified technician should install and service this device.

• Never attach devices to the VDL8LS when it is not fully installed and all connections are secured and safety pins are in place. Never change the height of the system with devices already attached.

General Guidelines

Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.

• Indoor use only. Keep this device away from rain, moisture, splashing and dripping liquids.
• Protect this device from shocks and abuse. Avoid brute force when mounting the device and during use.
• All modifications of the device are forbidden for safety reasons. Damage caused by user modifications to the device is not covered by the warranty.
• Only use the device for its intended purpose. Using the device in an unauthorised way will void the warranty.
• Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer will not accept responsibility for any ensuing defects or problems.
• Have the device installed by a qualified person, respecting EN 60598-2-17 and all other applicable norms.
• The carrying construction must be able to support 10 times the weight of the device for 1 hour without deforming.
• Never stand directly below the device when it is being mounted, removed or serviced.
• Have a qualified technician check the device once a year and each time before you bring it into service.
• Overhead mounting requires extensive experience: calculating workload limits, determining the installation material to be used… Have the material and the device itself checked regularly. Do not attempt to install the device yourself if you lack these qualifications as improper installation may result in injuries

Mounting

Refer to the illustrations on pages 2 of this manual.

1 Truss

• A] Locate the short bar (±19cm/7.3”; without pre-drilled holes) and two T-joints (without safety pin) and attach them together as indicated.
• [B] Insert a short bar (±19cm/7.3”; with pre-drilled holes). (2x)
• [C] Align the holes and secure the connection with a bolt and wing nut. Place a washer on either side of the bar.(2x)
• [D] Slide the assembly [A] over the truss.
• [E] Connect the two trusses as indicated.
• [F] Secure the connection with a bolt and wing nut. Place a washer on either side of the bar. (2x)
• [G] Secure the vertical bar in the T-joints with the butterfly nuts. (4x)
  Note: the system can also be used with only a single truss between the two side bars. In this case, skip step 1.

2 Side bar

• Locate an 80cm/31.5” top bar and slide into the 165cm/64” bottom bar, align the holes and secure the connection with a bolt and wing nut. Place a washer on either side of the bar.
• Secure the butterfly nut for additional strength.
• Slide two T-joints (with safety pin) over the top bar. Do not secure them yet.
• Repeat above procedure to assemble the second side bar.

3 Tripod

• Open a tripod and secure it with the butterfly nut.
• Slide the bottom part (with pre-drilled holes) of a side bar (see [2]) in the tripod.
• Determine the desired height. Insert a safety pin through the applicable pre-drilled hole. The safety pin will rest on the tripod (see illustration).
• Secure the butterfly nut of the tripod.
• Repeat the above procedure for the other side.

4 Mount truss

This step should be performed by two adult persons.

• Insert the truss (see [1]) simultaneously into the two T-joints of the side bars.
• Insert the safety pin through the T-joints and secure the butterfly nuts of the trusses.
• Determine the desired height, make sure the truss is level and secure the butterfly nuts on the side bars.

5 T-bar

• Place a T-bar on top of each side bar. Rotate it in the desired angle and secure it with the butterfly nut.
• Use the included bolts to attach devices (not incl.) to the T-bars.

Cleaning and Maintenance

• All screws should be tightened and free of corrosion.
• The device should not be deformed, modified or tampered with e.g. do not drill extra holes in mounting supports, do not change the location of the connections …
• Wipe the device regularly with a moist, lint-free cloth. Do not use alcohol or solvents.

INSTALLATION INSTRUCTIONS

Technical Specifications

colour ……………………………………………………………………………………………………… black
max. load ……………………………………………………………………………………. 80 kg (175 lbs)
max. height …………………………………………………………………………………….. 2.75 m (9 ft)
width ………………………………………………………………………. 1.53 m (5 ft) or 3.05 m (10 ft)
weight ………………………………………………………………………………………….. 19 kg (42 lbs)

Use this device with original accessories only. Vellemannv cannot be held responsible in the event of damage or injury resulting from (incorrect) use of this device. For more info concerning this product and the latest version of this manual, please visit our website www.hqpower.eu. The information in this manual is subject to change without prior notice.

© COPYRIGHT NOTICE
The copyright to this manual is owned by Velleman nv. All worldwide rights reserved. No part of this manual may be copied, reproduced, translated or reduced to any electronic medium or otherwise without the prior written consent of the copyright holder

References

• Details – Own brands – Velleman – Wholesaler and developer of electronics
• Velleman – Wholesaler and developer of electronics

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>