Campark SC17 Wireless Mini NVR Kit User Guide

Campark SC17 Wireless Mini NVR Kit

Statement

Thank you very much for purchasing our products.
This user manual will introduce the main uses of the products. If you have any questions, please feel free to contact us at

SC@yooomail.com

Due to software and hardware upgrades or changes, this manual may contain inaccurate content without prior notice. If there is any discrepancy between the description of the product and the actual product, the actual product shall be used as the standard.

Safety Caution

❶ Please do not put any uid container on the product.
❷ Please use the product in ventilated environment and prevent blocking the vents.
❸ Please use included power supply with the product to prevent damage to the product.
❹ Please use the product under its standard working temperature and humidity. (advised in this manual or distributor’s website)
❺ Dust on PCB may cause short circuit. It is suggested to clean the dust on PCB timely to make the product work properly.
❻ Please obey the regulation and policy in your country and area during the installation of this.

NVR

❶ Antenna port:Dual antennas expand the WIFI range;
❷ WAN port: Connect the NVR to the Internet;
❸ TF card slot TF card interface;
❹HDMI interface: Connect to high-denition TV;
❺ USB port: Connect mouse and U disk;
❻ Power supply: DC power input (12V 2A);
❼ RESET: Press and hold for 3 seconds to reset (clear the password, network and other settings, do not clear the camera channel, release the button and restart to take eect), continue to press the reset button for 10 seconds to reset all (clear the password, including all settings such as camera channels and so on);

IPC

Product Overview Camera:

1. Lens

2. PIR Sensor

3. LED

4. lndicator

5. Micrphone
   

6. RESET

7. ON/OFF

8. lYPE C port

9. Speaker

10. Antenna

Power off

Hard disk installation

❶ Open the hard disk cover on the back of the chassis and remove the cover.

❷ Align the hard disk socket with the wiring port on the NVR, insert the hard disk, and pay
attention to the direction of the hard disk.

❸ Align the hard disk with the hard disk socket and push it to the left to x the hard disk.

❹ Close the hard disk cover.

System connection and installation

Connect the system as shown in the steps below

❶ Insert one end of the HDMI cable into the HDMI port of the NVR rear panel, and the other end into the HDMI port of the TV or monitor;
❷ Insert the USB mouse into the USB port on the NVR rear panel;
❸ Connect one end of the network cable to the WAN network interface of the NVR rear panel, and the other end to the home router or network access point;
❹ Connect the power adapter connector to the power socket on the NVR rear panel, and then insert the adapter into the surge protector or uninterruptible power supply (UPS); make sure that the surge protector or uninterruptible power supply (UPS) switch is ON, After a few moments, the NVR splash screen will appear on the screen;
❺ Press and hold the power button of the camera for 2 seconds to turn it on .

System wiring diagram

Configure WNVR on TV or Monitor

After powering on, please follow the steps of the setup wizard to complete the settings of language, network, time, view real-time screen, password, hard disk and download APP and device. If you see the prompt “Network status is good!” in the network setup wizard interface, it means your recorder has successfully connected to the Internet.
(Tips: If there is no Internet near your video recorder device, you can also choose to use it without connecting to the Internet. This method will make it impossible to use the mobile APP to watch the video from a long distance.)

Menu bar

Right-click and you’ll go to the main menu, right-click again to exit the menu or go back.

• Split screen selection: Change the view state, you can choose to view multiple or single cameras.
• Video playback: Enter the video playback interface to play the recorded video.
• Camera Settings: View the settings related to the added camera.
• System Settings: Manage all system settings.
• Channel Sort: Adjust the camera channel sorting order.
• Device Diagnosis: Diagnose camera status, signal and rmware version.
• Network Settings: View your device’s network connection.
• Exit the system: logout, restart, shutdown functions.
  

System Settings

Right click on the mouse – select System Settings: You can modify system- related settings.

• General settings : Set language, display resolution, audio volume and view rmware information.
• Camera settings : All camera settings, alarm settings, recording settings.
• Date/Time : Set device time, date and time zone information.
• Network settings : Network connection to router settings, wireless channel settings.
• Device Diagnosis : Device and added camera status detection and diagnosis.
• Storage settings : View hard disk orTFcard information and format.

Channel Toolbar

Move the left mouse button to the corresponding channel, and the toolbar at the bottom of the pop-up channel will be activated. Click the corresponding icon to enable the corresponding function settings.
From left to right: Audio output switch button, camera light control and color adjustment button, PTZ control button, talkback button, channel full-screen playback button.

Recording settings

Right click on the mouse → select camera settings → select recording mode on the right side of the interface

Camera working mode
The battery camera includes three modes: Best power saving, best video recording, and always video recording;
The constant power camera includes two modes: constant recording and event recording; the specie mode function introduction is entered into the setting interface for detailed viewing, and the corresponding working mode is selected according to the usage scene of your device.

Smart detection settings
Right click on the mouse button c◊ select camera settings c◊ enable smart detection on the right side of the interface, click smart detection settings.
You can set the camera’s detection area, sensitivity level, detection type (humanoid), humanoid frame switch and other functions;

Smart detection period setting
Right -click on the mouse → select camera settings → detect time period settings on the right side of the interface.
During the set time period, the device will detect the motion and start recording, here you can set any time period you want to record, such as 0:00:00-23:59:59 every day, which is 24h•7 days of recording; video recorder When the hard disk is detected, the system defaults to record 24h•7 days.
(Reminder: battery camera does not support 24H continuous recording)

Video Playback

1. Right-click on the video preview interface and enter the playback interface, it will automatically start retrieving the video of the day (default video playback);
2. Select the video playback type (video playback or smart playback), select the date and channel, and select the recording type (movement, timing, humanoid), and the recording will be retrieved in real time;
3. Function introduction:

❶ Button description: Play; Fast forward 2 times, 4 times, 8 times; Switch between 1 and 4 channels; Play in full screen;
❷ Timeline: You can click 24h, 1 h, 30m in the lower left corner to switch the unit of the time axis. In the area with the video time axis, click the left mouse button to start playback from the time the mouse clicked.
❸ Smart playback : Click the video thumbnail below to play the video recording, and select the options of human shape, and mobile recording to view only the corresponding type of video clips(Note: SD card video recording does not support intelligent layback.
❹ AII recordings : Click on all recordings to display the required recording clips of the current channel, and you can select the recordings in the corresponding time period to play

Video Backup

You can use a USB ash drive to backup videos, which is easy and convenient. In the video playback interface, select the channel window that needs to be backed up II click the backup video button in the lower right corner → insert the U disk → select the export folder—-> click export.
(Reminder: U disk format currently only supports U disk in FAT32/exFAT format for backup, and video les are packaged once an hour)

Add IP Camera (IPC)

1. Automatically add: The wireless camera that is shipped together with the recorder equipment, just connect the power supply, wait for a period of time, the recorder will automatically add the camera, and you can view the successfully added camera screen in the preview interface .
   

2. Manually add:
   Step 1: Click the”+” icon at the bottom of the preview interface.
   Step 2: Reset the camera or connect the camera to the recorder with a network cable, click Next.
   Step 3: After the camera to be added is found in the waiting list, click Next.
   Step 4: Check the video screen of the camera, after conrming that the camera has been added successfully, click Next to enter the preview interface.
   (Tips: When adding a camera, please try to place the camera and the recorder as close as possible)
   

APP remote viewing video

❶ Download and install
You can search for “cloudeye” in App Store, App Store and other application markets to download. Or scan the QR code below to download.
Note: Apple mobile phone system requires iOS system 9.0 or above, Android mobile phone system requires Android 5.1 or above.

|
---|---
|

IOS

|

Android

❷ Registration and Login

1. Click Register, input your mobile phone number/email, input the verication code, and complete the registration;
2. Enter your registered mobile phone number and password on the login interface, and click Login;
3. Click the third-party application icon at the bottom of the login interface, and you can log in successfully after completing the authorization.
   

❸ Add device

1. Click “+” on the device list interface to add a camera;
2.  Scan the ID QR code on the recorder (click the QR code icon in the lower right corner of the preview interface);
3. Set the device name to add successfully.
   

View video screen and video playback

Device List Click the device card to enter the video preview interface, select View Playback to view the channel video recording of the recorder.

(Tips: Please make sure that your video recorder is connected to the Internet when using the cloudeye APP to add and view the video recorder screen)

Expand Wireless Coverage

Wireless connection is simple and convenient, but wireless is not everything! Because of the wireless characteristics, in some complex scenarios, there is a signal attenuation situation after passing through obstacles. Extend the signal transmission distance by placing the antennas reasonably as follows.

Reasonably adjust the antenna and optimize the signal radiation

direction

As can be seen from the bar antenna gain chart as shown on the right, the signal coverage of the antennais similar to anapple. The antenna is located in the center of the apple.and the signal around the antennais strong. The upper and lower ends of the antenna are recessed, and the signal is weak.

According to the signal transmission characteristics of the antenna, in order to
ensure the optimal image transmission eect of the wireless NVR Kit, it is required:

1. The antennas of the NVR and IPC should be placed in a high and open place, and not near the walls, metal, glass and other obstacles, which will aect the signal’s outward divergence.
2. The antenna of the IPC should be placed in parallel with the NVR antenna as much aspossible so that the respective maximum radiation direction angles are opposite to formthe maximum signal coverage, as shown in the gure below.
   

Camera installation method

Note: Here we only take the battery camera as an example to illustrate the installation method of the camera and solar panel.

1. Use positioning paper to punch holes, the cement wall needs to be nailed with rubber plugs;

2. Fix the base with screws;

3. Adjust the tilt angle of the camera to a suitable position and then tighten the xing screws;

4. Install the solar panel as far as possible in the position with the longest sunlight.
   Pull out the rubber stopper

Insert the 1YPE-C cable

FAQs

1. If the phone receives alarm messages too frequently, the camera will consume battery power greatly. It is recommended to lower the motion detection sensitivity, set the alarm interval, and start the alarm plan.
2. If you find that there are no moving objects in the alarm picture that the phone frequently receives, it may be that there is a sensitive heat source in the motion detection range, which causes the PIR to be triggered by mistake. It is recommended to lower the motion detection sensitivity.
3. If you detect that someone is passing by the camera but cannot receive the alarm message, it is recommended to increase the motion detection sensitivity.
4. If you find that the alarm picture or video is delayed, or you can only see the back of people, it is recommended to increase the motion detection sensitivity.
5. The PIR sensor will be disturbed by the ambient temperature. It is recommended to increase the motion detection sensitivity in a hot environment, and decrease the motion detection sensitivity in a cold environment. At the same time, when the temperature is extremely low, heavy clothes will hinder PIR sensor detection.
6. The ultraviolet rays of the sun will interfere with the PIR sensor. When the PIR of the camera is directly facing the strong sun, there is a probability that the alarm will not be sensitive.

The device prompts offline?

1. Check whether the equipment is in the power-on state, and observe whether the working light of the equipment is on normally.
2. Check whether the WIFI network is in good condition and restart the router.
3. If the device is located far away from the router, which results in the inability to obtain a good WIFI signal, it is recommended to move the router to a closer place or add a WIFI amplifier to improve the WIFI performance of the home.
4. Delete the floodlight camera from your CloudEye account and add it again after resetting the device.
5. Check whether the device firmware and application program are the latest version.

Update router or WIFI password?

Delete the camera from your Cloud Eye account. After resetting the device, use the new WIFI or password to add it again.

Alarm push frequently?

1. In the app, lower the sensitivity of the motion detection alarm.
2. Check whether there are objects that interfere with and trigger the PIR sensor in the field of view of the equipment, such as the outdoor unit of the air conditioner, driving cars, passing pedestrians, etc. The angle of the device can be adjusted appropriately to avoid these easily disturbing objects

The phone cannot receive the alarm push?

1. Set in the mobile phone system and enable the push permission of the “CloudEye” application.
2. Make sure the device’s motion detection function is successfully turned on.
3. Restart the phone, and the Android phone tries to clear the cache.
4. Check whether the network is good.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>