BRAINLIT ALVEN Indoor Lamp User Guide

June 6, 2024
BRAINLIT

BRAINLIT ALVEN™ – QUICK GUIDE

Welcome to the world of BioCentric Lighting™
BrainLit Alven™ is the world’s first personal, connected, and dynamic BioCentric Lighting™ system in a free-standing LED luminaire. It is a multi- user system and can also be connected to the BrainLit cloud.
The Autolite recipe of BrainLit Alven™ provides optimal light conditions for aligning your circadian rhythm. The light conditions can be further adjusted through the BrainLit app. With the app, you can choose e.g. the “Boost” scene to receive a light shower for extra energy.

Before assembly
Two people recommended for assembling and moving your Alven
For indoor use only

  1.  Remove all packaging materials.
  2. Unpack and inspect all components.
  3.  Layout all parts on a flat surface..

A 1x Alven luminaire
B 1x Alven pole
C 1x Alven foot
D 8x Assembly bolts
E 1x Torx key
F 1x Power cord
G 1x Documents
– User manual
– Quick guide
F Power cord type X. The flexible cable or cord may be specially prepared and only available from the manufacturer or his service agent.

Attach the foot to a pole

Lay the pole (B) on a stool or chair horizontally to avoid damage, approximately 70 cm above the surface as pictured below.
Attach the foot (C) to the bottom end of the pole (B) with four of the eight bolts (D) using the Torx key (E).

Attach luminaire to the pole

NOTE: Please take care not to pinch or damage the wires.
Connect the wire and quick connector from the luminaire (A) with the matching connector from the pole (B), making sure they are firmly connected and that the latching hooks have connected properly.
Thread the luminaire (A) over the pole (B) and make sure that all cables are running free into the pole (B) and are not pinched or damaged.
Attach the luminaire (A) to the top end of the pole (B) with the remaining four bolts (D) using the torx key (E).

Connect power

Raise your Alven to a standing position with its foot on the floor. Insert the power cable (F), first to your Alven and then to the wall outlet. It will take about 2 minutes for your Alven to start once the power cord has been connected.
Alven can be connected to a network using wifi or an ethernet cable (not provided). The flexible cable or cord may be specially prepared and only available from the manufacturer or his service agent.
NOTE: Do NOT connect to a Power over Ethernet (PoE) connection.  This device is not PoE compatible. TURN PAGE FOR OPERATING INSTRUCTIONS →

STEP4

Start system

Use the power button to power your  Alven On/Off.
Do not look directly into BrainLit Alven’s light. It is brighter than a normal lamp and may cause discomfort.
For more features, see instructions in section 3.1 of this user manual or in the app.

STEP 5

Complete setup

Complete the setup of your Alven by downloading the BrainLit app from the App Store or Google Play Store and following the instructions.

|
---|---
https://apps.apple.com/app/id1535202789| https://play.google.com/store/apps/details?id=com.brainlit.bclapp

**STEP 6

** Finished

You’re all set! Welcome to the world of BioCentric Lighting™. Scan the QR code for the full documentation to view more features.

https://www.brainlit.com/alven-documentation

Bluetooth pairing – How to enable Bluetooth pairing mode on your BrainLit Alven™

  1.  LONG press (3 sec) Power
  2.  Power LED blinks slowly
  3.  Within 7 sec LONG press (3 sec)
  4. Power LED is ON and Bluetooth LED blinks slowly when pairing is active Bluetooth pairing is active for 60 sec. Follow instructions on your phone or mobile device to complete pairing.

Autolite

The Autolite recipe is the default setting that best helps you maintain your circadian rhythm. The circadian rhythm is referred to as our ”biological clock” that regulates our well-being, alertness, and sleep. To maintain your normal circadian rhythm you should use AutoLit without dimming the light intensity as often as possible.
If you adjust the brightness of BrainLit Alven using the (+) or (-) buttons, you will exit AutoLit and the light will remain at a static light intensity until you turn BrainLit Alven off and back on. It may take a few days for your eyes to adapt to the brightness of your BrainLit Alven™. Colour pr PrintMatte finish
To activate AutoLit recipe

  1.  LONG press (3 sec) Power
  2. Power LED blinks slowly
  3. Within 7 sec SHORT press Power
    = recipe changes to AutoLit color print information

Boost

Boost increases your alertness and stimulates your cortisol levels, giving you a refreshing effect. Recommended usage is a 20 minutes or shorter ”light shower” preferably during the first half of the day (08.00-14.00).
Usage of Boost at night may disturb your natural circadian rhythm. To maintain your natural circadian rhythm, you should use AutoLit without dimming the light intensity as often as possible.Print To activate Boost scene

  1.  LONG press (3 sec) Power
  2.  Power LED blinks slowly
  3.  Within 7-sec SHORT press**+=** scene changes to Boost

Relax

Colour print information Relax creates a natural light environment that feels more neutral to your eyes but does not change dynamically and therefore has less impact on your
circadian rhythm. Recommended usage is for shorter time periods after 14.00. Pantone 281 C Matte finish
To maintain your circadian rhythm you should use AutoLit without dimming the light intensity as often as possible.

To activate Relax scene

  1.  LONG press (3 sec) Power
  2. Power LED blinks slowly
  3. Within 7-sec SHORT press scene changes to Relax

Autolite Demo – Shows the variation and dynamics of the light Print

  1. LONG press (3 sec) Power
  2. Power LED blinks slowly
  3. Within 7 sec LONG press (3 sec)**+**
  4. Demo of AutoLit is running
  5. Power LED blinks fast and Bluetooth LED is OFF when the demo is running
    The demo will last for approximately 90 sec.

www.brainlit.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals