BRAINLIT Luminaire Surface Mounts and Pendants Instruction Manual
- June 8, 2024
- BRAINLIT
Table of Contents
BRAINLIT Luminaire Surface Mounts and Pendants
Mounting
BALDER can be mounted in two different ways.
Surface installation
- -Install the bracket on the ceiling. Use screws and plugs suitable for your ceiling.
- Perform the electrical installation according to standards and regulations in your region (see “Electrical installation”).
- Connect the luminaire to the bracket. Make sure that the pins fit in the holes of the bracket. Rotate the luminaire slightly to make it stay.
Suspended installation
- Install the canopy on the ceiling. Use screws and plugs suitable for your ceiling.
- Perform the electrical installation according to standards and regulations in your region (see “Electrical installation”).
- Adjust height of the luminaire and attach the canopy lid.
Electrical Installation
EU WAGO Connect the WAGO connectors.
EU terminal Connect the two DALI wires to the orange terminals DA+ and DA-. DALI is polarity insensitive. Connect neutral (N) to white terminal, line (L) to black terminal and protective ground to green terminal.
Data
BALDER 90
Maximum circuit breaker B10 B13 B16 C10 C13 C16
loading (no of luminaires) : @230V 21 27 33 21 27 33
BALDER 60
Maximum circuit breaker B10 B13 B16 C10 C13 C16
loading (no of luminaires): @230V 43 56 69 43 45 69
Format diameter: EU (mm): 600, 900 Pendant
Light source energy class: E
User-replaceable light source: No
Warning
- Disconnect or turn power off before installation, maintenance or service.
- Installation requires knowledge of luminaire’s electrical sys-tems. If not qualified, do not attempt installation. Contact a qualified electrician.
- Brainlit’s luminaires must be installed in compliance with international wiring regulations (EN, IEE, NEC etc.).
- Secure luminaire compatibilty with input voltage and frequency.
- To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or sharp objects.
- Risk of fire or electric shock. Keep combustible and other inflammable materials away from lamp/lens.
- The luminaire is not suitable for covering with thermally insu-lating material.
- Do not operate in close proximity to persons, inflammable materials or substances affected by heat or dying.
- Wear gloves and safety glasses when removing luminaire from carton, installing, servicing or performing maintenance.
- Do not touch enclosure or light source.
- Allow lamp/luminaire to cool down before handling.
- The connecting cable is not waterproof.
- No user-serviceable parts inside of the luminaire.
- Luminaire to be independently supported to the building structure.
- Avoid direct eye exposure to light sources when the luminaire is on.
This document contains information that is subject to change without notice. This document is solely intended for, and may only be used for, the purpose of providing luminaire products to the BrainLit BioCentric Lighting System. The performance indications for BrainLit products set forth in this document are based on, and conditioned on, the products being used solely in the BrainLit BioCentric Lighting System. However, this document shall not be deemed a product warranty, whether express or implied. The BrainLit product warranty is solely contained in the purchase agreement with each customer. This document is subject to BrainLit AB’s copyright. No part of this document may be reproduced or transmitted in any form or by any means, or shared with any third party, without the prior written approval of BrainLit AB. BrainLit products may be protected by one or more patents and by copyright and design rights. “BrainLit” and “BioCentric Lighting” are registered trademarks of BrainLit AB. This document does not confer upon the recipient a license to any of BrainLit intellectual property rights.
BrainLit AB
Scheelevägen 34, 223 63 Lund, Sweden
+46 46-37 26 00 info@brainlit.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>