eurolite TMH-S60 Moving Head Spot Light User Manual

eurolite TMH-S60 Moving Head Spot Light

LED TMH-S60 Moving Head Spot

DANGER! Electric shock caused by short-circuit
Be careful with your operations. With a dangerous voltage you can suffer a dangerous electric shock when touching the wires. Never open the housing. Keep the device away from rain and moisture.

Please read these instructions carefully before using the product. They contain important information for the correct use of the product.

Every person involved with the installation, operation and maintenance of this device has to

• be qualified
• follow the instructions of this manual
• consider this manual to be part of the total product
• keep this manual for the entire service life of the product
• pass this manual on to every further owner or user of the product
• download the latest version of the user manual from the Internet

INTRODUCTION

Thank you for having chosen one of our products. If you follow the instructions given in this manual, we are sure that you will enjoy this device for a long period of time.

Product features

Compact Moving Head Spot with 60 W LED, gobos and color wheel

• Positioning within 540° PAN and 180° TILT
• Exact positioning via 16-bit PAN/TILT movement resolution
• Electronic dimmer (0-100%)
• 1 powerful LED 60 W COB (chip-on-board) cold white (CW)
• Color wheel 7 dichroic filters plus open, rainbow effect with adjustable speed in both directions
• Gobo wheel with rotating gobos, 7 gobos and open, slot-in gobo system for exchanging gobos without tools; 3 gobos with heart patterns for exchange included
• Shake effect
• 4 integrated show programs
• Can be operated in 10; 12 CH mode
• The device is cooled by cooling fan
• Controlling by stand-alone; DMX; Sound to light via Microphone; Master/slave function; CRMX by Lumen Radio via USB (optional); W-DMX by wireless solution via USB (optional); Quick DMX via USB (optional)
• Flicker-free projection
• Effect: Single Beam; Strobe effect
• With a beam angle of 12°
• 4 digits 7-segment LED display for easy controlling
• With rubber feet

SAFETY INSTRUCTIONS

WARNING!
Please read the safety warnings carefully and only use the product as described in this manual to avoid accidental injury or damage.

Intended use

• This device is an LED moving-head lighting effect for creating decorative effects. This device is designed for professional use in the field of event technology, e.g. on stage. It is not suitable for household lighting.
• Only use the device according to the instructions given herein. Damages due to failure to follow these operating instructions will void the warranty! We do not assume any liability for any resulting damage.
• We do not assume any liability for material and personal damage caused by improper use or non-compliance with the safety instructions. In such cases, the warranty will be null and void.
• Unauthorized rebuilds or modifications of the device are not permitted for reasons of safety and render the warranty invalid.

Danger due to electricity

• The device is suitable for indoor use only. Do not use it outdoors. Never expose it to rain or moisture. Do not store it in rooms exposed to moisture.
• To reduce the risk of electric shock, do not open any part of the device. There are no serviceable parts inside the device.
• Only connect the device to a properly installed mains outlet. The outlet must be protected by residual current breaker (RCD). The voltage and frequency must exactly be the same as stated on the device. If the mains cable is equipped with an earthing contact, then it must be connected to an outlet with a protective ground. Never deactivate the protective ground of a mains cable. Failure to do so could possibly injure the user.
• The mains outlet must be easily accessible so that you can unplug the device quickly if need be.
• Never touch the mains plug with wet or damp hands. There is the risk of potentially fatal electric shock.
• The mains cable must not be bent or squeezed. Keep it away from hot surfaces or sharp edges.
• Never pull the mains cable to disconnect the mains plug from the mains outlet, always seize the plug.
• Unplug the device during lightning storms, when unused for long periods of time or before cleaning.
• Do not expose the device to any high temperatures, direct sunlight, dripping or splashing water, strong vibrations or heavy mechanical stress.
• Do not place any objects filled with liquids on the device.
• Do not place any open sources of fire, such as burning candles, on or directly next to the device.
• Make sure that objects cannot fall into the device, in particular metal parts.
• Only have repairs to the device or its mains cable carried out by qualified service personnel. Repairs are required when the device or the mains cable is visibly damaged, liquid has been spilled or objects have fallen into the device; when the device has been exposed to rain or moisture, has been dropped or malfunctions occur.
• Cleaning of the device is limited to the surface. Make sure that moisture does not come into contact with any areas of the terminal connections or mains voltage control parts. Only wipe off the product with a soft lint-free and moistened cloth. Never use solvents or aggressive detergents.

Danger to children and people with restricted abilities

• This product is not a toy. Keep it out of the reach of children and pets. Do not leave packaging material lying around carelessly. Never leave this device running unattended.
• This device may be used only by persons with sufficient physical, sensorial, and intellectual abilities and having corresponding knowledge and experience. Other persons may use this device only if they are supervised or instructed by a person who is responsible for their safety.

Warning – risk of burns and fire

• The admissible ambient temperature range (Ta) is -5 to +45°C. Do not operate the device outside of this temperature range.
• The housing temperature (Tc) can be up to 65°C during use. Avoid contact by persons and materials.
• Do not illuminate surfaces within 20 cm of the device. This value is indicated on the device by the symbol.
• Do not use the device near highly flammable materials. Always place the device at a location where sufficient air circulation is ensured. Leave 50 cm of free space around the device. Never cover the air vents of the housing.

Warning – risk of injuries

• Do not look directly at the light source. Persons with light-sensitive epilepsy may suffer from epileptic seizures or fall unconscious.
• Make sure that the product is set up or installed safely and expertly and prevented from falling down. Comply with the standards and rules that apply in your country, in particular EN 60598-2-17.
• If you lack the qualification, do not attempt the installation yourself, but instead use a professional installer. Improper installation can result in bodily injury and or damage to property.
• The manufacturer cannot be made liable for damages caused by incorrect installations or insufficient safety precautions.
• For overhead use, always secure the device with a secondary safety attachment such as a safety bond or safety net.
• Make sure that the area below the installation place is blocked when rigging, derigging or servicing the device.
• For commercial use the country-specific accident prevention regulations of the government safety organization for electrical facilities must be complied with at all times.

Caution – material damage

• This device must not be connected to the mains voltage by means of a dimmer.
• Lighting effects are not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects.
• Never switch the device on and off in short intervals. This will considerably reduce the service life of the device.
• If the device has been exposed to drastic temperature fluctuation, do not switch it on immediately. The resulting condensation may destroy the device. Allow the device to reach room temperature before connecting it. Wait until the condensation has evaporated.
• Please use the original packaging to protect the device against vibration, dust and moisture during transportation or storage.
• If a serial number label is affixed to the device, do not remove the label as this would make the warranty void.
• Never lift the fixture by holding it at the device head, as the mechanics may be damaged.

DESCRIPTION OF THE DEVICE

1. Device head

2. Manual focus

3. Lens/LED

4. Yoke

5. Base

6. Rubber foot

7. LED display

8. Menu button

9. Up button

10. Down button

11. Enter button

12. Microphone

13. Fuse holder

14. USB port for Quick DMX receiver

15. Power input

16. DMX input

17. DMX output

18. Ventilation grille

INSTALLATION

WARNING! Risk of injury caused by falling objects
Devices in overhead installations may cause severe injuries when crashing down. Make sure that the device is installed securely and cannot fall down. The installation must be carried out by a specialist who is familiar with the hazards and the relevant regulations.\

1. Omega brackets
2. Coupler
3. Safety bond
4. Quick-lock fastener

The device may be placed on the floor or fastened to a truss or similar rigging structure. The device must never be fixed swinging freely in the room.

1. The rigging structure must support at least 10 times the weight of all fixtures to be installed on it.
2. Block access below the work area and work from a stable platform when installing the device.
3. Use rigging hardware that is compatible with the structure and capable of bearing the weight of the device. Please refer to the “Accessories” section for a list of suitable rigging hardware and follow the instructions mentioned at the bottom of the base. Screw one coupler via a M10 screw and self-locking nut onto the Omega bracket. Insert the two quick-lock fasteners of the Omega bracket into the respective holes on the bottom of the device. Tighten the quick-lock fasteners fully clockwise.
4. Secure the device with a safety bond or other secondary attachment. This secondary safety attachment must be sufficiently dimensioned in accordance with the latest industrial safety regulations and constructed in a way that no part of the installation can fall down if the main attachment fails. For the attachment of a safety bond, the supplied eyelet must first be mounted on the device. Install the safety bond by inserting the quick link in the eyelet on the bottom of the base. Pull the safety bond over the trussing system etc. Insert the end in the quick link and tighten the fixation screw. Fasten the safety bond in such a way that, in the event of a fall, the maximum drop distance of the device will not exceed 20 cm.
5. Make sure that the Omega bracket is always in line with the truss structure when installing the device vertically.
6. After installation, the device requires inspections periodically to prevent the possibility of rot, deformation and looseness.

Inserting/Exchanging gobos

DANGER!
Install the gobos with the device switched off only. Unplug from mains before!

If you wish to use other forms and patterns as the standard-gobos, or if gobos are to be exchanged, please follow the instructions below:

The side of the device head to be opened is marked with a dot.

1. Open the device head via the four housing screws (see Graphic 1).
2. Carefully remove the gobo (see Graphic 2).

CAUTION!
Never unscrew the screws of the rotating gobo as the ball bearing will otherwise be opened!

Remove the fixation-ring with an appropriate tool.
Remove the gobo and insert the new gobo. Press the fixation-ring together and insert it in front of the gobo.

Note!
Slot-in gobo-system for exchanging gobos without tools! Inserting/Exchanging gobos as described above.

CONNECTIONS

DMX512 connection / connection between fixtures

The wires must not come into contact with each other; otherwise the fixtures will not work at all, or will not work properly.
Please note the starting address depends upon which controller is being used.

DMX512 control
A DMX512 data link is required in order to control the device via DMX. The device provides 3-pin XLR connectors for DMX connection.

1. Connect the output of your DMX controller to the DMX input DMX IN of the device with a DMX cable.
2. Connect the DMX output DMX OUT of the device to the DMX input of the next unit in the chain. Always connect one output to the input of the next unit until all units are connected.
3. At the last unit, the DMX cable has to be terminated. Plug the terminator with a 120 Ω resistor between Signal (–) and Signal (+) in the DMX output of the last unit.
4. If the cable length exceeds 300 m or the number of DMX devices is greater than 32, it is recommended to insert a DMX level amplifier to ensure proper data transmission.

XLR connection:

Wireless DMX transmission with Quick DMX
The device features an alternative DMX input for a Quick DMX receiver (sold separately). CRMX and WDMX receivers are compatible and can also be used. The connector allows a DMX control signal to be transmitted wirelessly to the device, eliminating the need for complex wiring to the DMX controller. The connector is designed as a USB port which provides the required 5 V operating voltage for the receiver.

Occupation of the USB port:

Connection to the mains
The device uses an auto-range power supply that accepts input voltages between 100 und 240 volts.

1. Connect the device via the enclosed mains cable to a grounded mains socket. Thus the unit is switched on.
2. To switch off the unit, disconnect the power plug.
3. Do not connect the unit to the mains voltage via a dimmer. For a more convenient operation, use a mains outlet which is switchable.

Stand-alone operation

• In stand-alone mode, the LED TMH-S60 can be used without controller.
• Disconnect the LED TMH-S60 from the controller and call up the internal program.
• Please refer to the instructions under Menu structure.

Master/Slave operation

• The master/slave operation enables that several devices can be synchronized and controlled by one master device.
• On the rear panel of the device you can find an XLR-jack (DMX Out) and an XLR-plug (DMX In), which can be used for connecting several devices.
• Choose the device which is to control the effects. This device then works as master device and controls all other slave-devices, which are to be connected to the master device via a DMX cable. Connect the DMX OUT-jack with the DMX IN-plug of the next device.
• Define the master device with the MAST setting then set the desired master mode “Auto” or “Sound”. Set the desired slave mode “SL 1” or “SL 2” on all slave devices. Please refer to the instructions under Menu structure.

OPERATION

• After connecting the device to the mains it is ready for operation.
• The display indicates the last operating mode.
• The operating modes can be selected by means of the display and the control buttons.
• All settings remain stored even if the device is disconnected from the mains.
• The device can be operated in stand-alone mode via the control board or in DMX-controlled mode via any commercial DMX controller.
• After you connected the effect to the mains, the EUROLITE LED TMH-S60 Moving-Head Spot starts running.
• During the Reset, the motors are trimmed and the device is ready for use afterwards.
• Turn the objective-lens for adjusting the focus in order to obtain a sharp projection.

Menu structure

• The main menu is accessed by pressing Menu until the display is lit.
• Browse through the menu by pressing Menu.
• Press Enter in order to select the desired menu.
• You can change the selection by pressing Up or Down.
• Press Enter in order to confirm.
• You can leave every mode by pressing Menu.
• The functions provided are described in the following sections.
• Depending upon the setting in the control board, the display shuts off after 10 seconds of inactivity.
• By pressing any button it lights up again.

Addr / DMX address setting
With this function, you can adjust the desired DMX address via the Control Board.

CHnd / DMX channel mode
With this function, you can select the desired DMX channel mode.

SLnd / Master / Slave setting
With this function, you can define the device as master or slave. You can choose one of two different Slave programs.
SL 1 = Synchronous movement, SL 2 = Asynchronous movement

SHnd / auto program
Auto mode (SH0 – SH3)
With this function, you can run 4 different internal programs.

Soud / music control
With this function, you can run the internal program sound-controlled.

SEnS / Mic sensitivity
With this function, you can select the desired microphone sensitivity between 0 % and 100 %.

blnd / no DMX status
With this function, you can set different modes if there is no DMX-signal.

LEd / Display turn off
With this function, you can shut off the display: ON the display stays lit; OFF the display turns off after 10 seconds.

dISP / display reverse
With this function, you can flip the display by 180° for a better view when the fixture is hung from a truss or a ceiling.

rPAN / Invert PAN
With this function, you can reverse the PAN-movement.

rTIL / Invert TILT
With this function, you can reverse the TILT-movement.

rESt / Reset
With this function you can reset the device via the Control Board.

DMX operation

Setting the DMX starting address
For operation with a controller with DMX512 protocol, the device is equipped with 12 control channels. However, it can also be switched to a mode with 10 channels if different functions are required. To be able to operate the device with a DMX controller, the DMX starting address must be set. The starting address depends upon which DMX controller is being used. Please refer to the controller’s documentation.

1. Press the MENU button so many times until Addr is indicated on the display. Confirm with the ENTER button.
2. Now the display calls up the menu item for the DMX starting address: A001.
3. Use the buttons UP and DOWN to set the address. Confirm with the ENTER button.
4. In order to choose the desired DMX channel mode, press the MENU button so many times until Chand is indicated on the display. Confirm with the ENTER button.
5. The display indicates 10 CH (10 DMX channels) or 12 CH (12 DMX channels). Use the buttons UP and DOWN to select the desired DMX channel mode. Confirm with the ENTER button
6. A dot will flash when DMX signals are being received.

Note: Please make sure that you do not have any overlapping channels in order to control each device correctly and independently from any other fixture on the DMX chain. If several devices are addressed similarly, they will work synchronically.

Functions in DMX mode

Gradual head adjustment from one end of the slider to the other (0-255, 128- center). The head can be stopped at any position you wish.
| PAN-movement with 16-bit resolution

2

| 0| 255| Fine indexing
__**2| Vertical movement (TILT)
3| __**

0

| __

255

| Push slider up in order to move the head vertically (TILT). Gradual head adjustment from one end of the slider to the other (0-255, 128- center). The head can be stopped at any position you wish.
| TILT-movement with 16-bit resolution 4
| 0| 255| Fine indexing
3| PAN/TILT speed 5
| 0| 255| Decreasing speed
4| Color- wheel
6| 0| 4| Open/White
5| 9| White + Red
10| 14| Red
15| 19| Red + Green
20| 24| Green
25| 29| Green + Blue
30| 34| Blue
35| 39| Blue + Yellow
40| 44| Yellow
45| 49| Yellow + Light blue

| | 50| 54| Light blue
---|---|---|---|---
55| 59| Light blue + Orange
60| 64| Orange
65| 69| Orange + Rose red
70| 74| Rose red
75| 79| Rose red + White
80| 166| Rainbow effect counter-clockwise with decreasing speed
167| 169| Stop
170| 255| Rainbow effect clockwise with increasing speed
__

__

6

| Gobo rotation
__

8

| 0| 4| No function
5| 126| Counter-clockwise gobo rotation with decreasing speed
127| 129| No function
130| 255| Clockwise gobo rotation with increasing speed
__

__

7

| Strobe
9| 0| 9| No function
10| 249| Strobe-effect with increasing speed
250| 255| No function
8| 10                                         Dimmer intensity
| 0| 255| Gradual adjustment of the dimmer intensity from 0 to 100 %
__

9

| Internal program, sound control
11| 0| 59| No function
60| 159| Internal program
160| 255| Sound control
__

__

10

| Special functions, reset
__

12

| 0| 20| No function
21| 100| PAN movement
101| 200| TILT movement
201| 249| PAN/TILT movement
250| 255| Reset

CLEANING AND MAINTENANCE

The outside of the device should be cleaned periodically to remove contaminants such as dust etc. The lens, in particular, should be clean to ensure that light will be emitted at maximum brightness.

1. Disconnect the device from power and allow it to cool before cleaning.
2. Clean the surface with a soft lint-free and moistened cloth. Never use alcohol or solvents as these may damage the surface. Make sure that no liquids can enter the device.
3. The device must be dry before reapplying power.
   There are no serviceable parts inside. Do not open the housing. Do not try to repair the device by yourself as this may result in damage. Maintenance and service operations are only to be carried out by authorized dealers.
   Should you need any spare parts, please use genuine parts. Should you have further questions, please contact your dealer.

Replacing the fuse
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.

1. Disconnect the device from power and allow it to cool.
2. Open the fuse holder of the mains connection with a fitting screwdriver.
3. Remove the old fuse from the fuse holder and replace it with a new fuse.
4. Carefully push the fuse holder back into its position before reapplying power.

PROTECTING THE ENVIRONMENT

Disposal of old equipment
When to be definitively put out of operation, take the product to a local recycling plant for a disposal which is not harmful to the environment. Devices marked with this symbol must not be disposed of as household waste. Contact your retailer or local authorities for more information. Remove any inserted batteries and dispose of them separately from the product.
You as the end user are required by law (Battery Ordinance) to return all used batteries/ rechargeable batteries. Disposing of them in the household waste is prohibited. You may return your used batteries free of charge to collection points in your municipality and anywhere where batteries/rechargeable batteries are sold. By disposing of used devices and batteries correctly, you contribute to the protection of the environment.

TECHNICAL SPECIFICATIONS

mounting version power supply cord with safety plug (provided)

Device fuse:| 5 x 20 mm, T 1,5 A Fuse replaceable
Lamp type:| LED lamp
LED:| 1 x 60 W COB (chip-on-board) cold white (CW)
Color temperature:| 7700K
Max. TILT movement:| 180°
Max. PAN movement:| 540°
Equipment:| Gobo wheel with rotating gobos; Focus manual; color wheel
Color generation:| Color wheel 7 dichroic filters plus open

Gobos:

| Gobo wheel with rotating gobos, 7 gobos and open
Outside diameter 13,8mm
Image diameter 11mm
Slot-in gobo system for exchanging gobos without tools
Shake effect
DMX channels:| 10; 12
DMX input:| 3-pin XLR (M) mounting version
DMX output:| 3-pin XLR (F) mounting version
Cooling:| Cooling fan

Control:

| Stand-alone; DMX; Sound to light via Microphone; Master/slave function; LED PC- Control 512; EASY SHOW; CRMX by LumenRadio via USB (optional); W-DMX by wireless solution via USB (optional); QuickDMX via USB (optional)
Beam angle:| 12°
Illuminance in Lux (lx):| Cold white (CW) 1m: 15205 lx, 3m: 1764 lx, 6m: 445 lx
Housing color:| Item no. 51786072 black, item no. 51786073 white
Display type:| 4 digits 7-segment LED display

Dimensions:

| Width: 17.0 cm
Depth: 15.0 cm
Height: 24.0 cm
Weight:| 3.45 kg

Accessories

All information is subject to change without prior notice. © 08.11.2022

Eurolite is a brand of Steinigke Showtechnic GmbH Andreas-Bauer-Str. 5 97297
Waldbüttelbrunn
Germany 00143841
Version 1.1 Publ. 08/11/2022

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>