eurolite BAR-9 LED Party UV Light User Manual

BAR-9 LED Party UV Light
User Manual
UV LED light bar with high-power 3 W LEDs for dynamic blacklight effects No. 51930309
www.eurolite.de

DANGER! Electric shock caused by short-circuit
Be careful with your operations. With a dangerous voltage you can suffer a dangerous electric shock when touching the wires. Never open the housing. Keep the device away  from rain and moisture.
Please read these instructions carefully before using the product. They contain important information for the correct use of the product.

Every person involved with the installation, operation and maintenance of this device has to
– be qualified
– follow the instructions of this manual
– consider this manual to be part of the total product
– keep this manual for the entire service life of the product
– pass this manual on to every further owner or user of the product
– download the latest version of the user manual from the Internet

INTRODUCTION

Thank you for having chosen one of our products. If you follow the instructions given in this manual, we are sure that you will enjoy this device for a long period of time.

Product features
UV LED light bar with high-power 3 W LEDs for dynamic blacklight effects

• Perfect for decorative and illumination purposes
• Ultra-light, ideally suited for mobile use
• Swivel mounting brackets
• Slender housing
• Available in two sizes

SAFETY INSTRUCTIONS

**WARNING!**
Please read the safety warnings carefully and only use the product as described in this manual to avoid accidental injury or damage.

Intended use

• This device is a spotlight for creating decorative lighting effects. This device is designed for professional use in the field of event technology, e.g. on stage. It is not suitable for household lighting.
• Only use the device according to the instructions given herein. Damages due to failure to follow these operating instructions will void the warranty! We do not assume any liability for any resulting damage.
• We do not assume any liability for material and personal damage caused by improper use or noncompliance with the safety instructions. In such cases, the warranty will be null and void.
• Unauthorized rebuilds or modifications of the device are not permitted for reasons of safety and render the warranty invalid.

Danger due to electricity

• The device is suitable for indoor use only. Do not use it outdoors. Never expose it to rain or moisture. Do not store it in rooms exposed to moisture.
• To reduce the risk of electric shock, do not open any part of the device. There are no serviceable parts inside the device.
• Only connect the device to a properly installed mains outlet. The outlet must be protected by residual current breaker (RCD). The voltage and frequency must exactly be the same as stated on the device. If the mains cable is equipped with an earthing contact, then it must be connected to an outlet with a protective ground. Never deactivate the protective ground of a mains cable. Failure to do so could possibly injure the user.
• The mains outlet must be easily accessible so that you can unplug the device quickly if need be.
• Never touch the mains plug with wet or damp hands. There is the risk of potentially fatal electric shock.
• The mains cable must not be bent or squeezed. Keep it away from hot surfaces or sharp edges.
• Never pull the mains cable to disconnect the mains plug from the mains outlet, always seize the plug.
• Unplug the device during lightning storms, when unused for long periods of time or before cleaning.
• Do not expose the device to any high temperatures, direct sunlight, dripping or splashing water, strong vibrations or heavy mechanical stress.
• Do not place any objects filled with liquids on the device.
• Do not place any open sources of fire, such as burning candles, on or directly next to the device.
• Make sure that objects cannot fall into the device, in particular metal parts.
• Only have repairs to the device or its mains cable carried out by qualified service personnel. Repairs are required when the device or the mains cable is visibly damaged, liquid has been spilled or objects have fallen into the device; when the device has been exposed to rain or moisture, has been dropped or malfunctions occur.
• Cleaning of the device is limited to the surface. Make sure that moisture does not come into contact with any areas of the terminal connections or mains voltage control parts. Only wipe off the product with a soft lint-free and moistened cloth. Never use solvents or aggressive detergents.

Danger to children and people with restricted abilities

• This product is not a toy. Keep it out of the reach of children and pets. Do not leave packaging material lying around carelessly. Never leave this device running  unattended.
• This device may be used only by persons with sufficient physical, sensorial, and intellectual abilities and having corresponding knowledge and experience. Other persons  may use this device only if they are supervised or instructed by a person who is responsible for their safety.

Warning – risk of burns and fire

• The admissible ambient temperature range (Ta) is -5 to +45°C. Do not operate the device outside of this temperature range.
• The housing temperature (Tc) can be up to 60°C during use. Avoid contact by persons and materials.
• Do not illuminate surfaces within 10 cm of the device. This value is indicated on the device by the symbol.
• Do not use the device near highly flammable materials. Always place the device at a location where sufficient air circulation is ensured. Leave 50 cm of free space around  the device. Never cover the air vents of the housing.

Warning – risk of injuries

• This product emits UV radiation which can cause irritation and damage to the eyes and to the skin. Reduce the exposure of eyes and skin to UV radiation to a minimum  in the close proximity of the device. Use appropriate shielding.
• Do not look directly at the light source. Persons with light-sensitive epilepsy may suffer from epileptic seizures or fall unconscious.
• Make sure that the product is set up or installed safely and expertly and prevented from falling down. Comply with the standards and rules that apply in your country, in  particular EN 60598-2-17.
• If you lack the qualification, do not attempt the installation yourself, but instead use a professional installer. Improper installation can result in bodily injury and or  damage to property.
• The manufacturer cannot be made liable for damages caused by incorrect installations or insufficient safety precautions.
• Make sure that the area below the installation place is blocked when rigging, derigging or servicing the device.
• For commercial use the country-specific accident prevention regulations of the government safety organization for electrical facilities must be complied with at all times.

Caution – material damage

• This device must not be connected to the mains voltage by means of a dimmer.
• Lighting effects are not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects.
• Never switch the device on and off in short intervals. This will considerably reduce the service life of the device.
• If the device has been exposed to drastic temperature fluctuation, do not switch it on immediately. The resulting condensation may destroy the device. Allow the device  to reach room temperature before connecting it. Wait until the condensation has evaporated.
• Please use the original packaging to protect the device against vibration, dust and moisture during transportation or storage.
• If a serial number label is affixed to the device, do not remove the label as this would make the warranty void.

DESCRIPTION OF THE DEVICE

Shown: 51930307, LED BAR-9 UV 9x3W

1.  W high-power LEDs, UV
2. Housing
3. Power input
4. Fixation screw
5. Mounting bracket
6. Mounting hole
7. Safety eyelet

WARNING! Risk of injury caused by falling objects
**** Devices in overhead installations may cause severe injuries when crashing down. Make sure that the device is installed securely and cannot fall down. The installation must be  carried out by a specialist who is familiar with the hazards and the relevant regulations.

This product is designed to be mounted on a floor, wall or ceiling. Depending on the surface, suitable screws and dowels must be used. Make sure that the product cannot fall  down.
Alternatively, the device may be fastened to a truss or similar rigging structure. The device must never be fixed swinging freely in the room.

1. The rigging structure must support at least 10 times the weight of all fixtures to be installed on it.
2. Block access below the work area and work from a stable platform when installing the device.
3. Use rigging hardware that is compatible with the structure and capable of bearing the weight of the device. Please refer to the “Accessories” section for a list of suitable  rigging hardware.
4. Secure the device with a safety bond or other secondary attachment. This secondary safety attachment must be sufficiently dimensioned in accordance with the latest  industrial safety regulations and constructed in a way that no part of the installation can fall down if the main attachment fails. An appropriate eyelet is mounted on the  device for fixation of the safety bond. Fasten the safety bond in such a way that, in the event of a fall, the maximum drop distance of the device will not exceed 20 cm.
5. To align the device, release the fixation screws at the mounting bracket, adjust the desired inclination angle and tighten the fixation screws.
6. After installation, the device requires inspections periodically to prevent the possibility of corrosion, deformation and looseness.

Shown: 51930307, LED BAR-9 UV 9x3W

CONNECTION TO THE MAINS
The device uses an auto-range power supply that accepts input voltages between 100 und 240 volts.

1. Connect the device via the power plug to a grounded mains socket. Thus the unit is switched on.
2. To switch off the unit, disconnect the power plug.
3. Do not connect the unit to the mains voltage via a dimmer. For a more convenient operation, use a mains outlet which is switchable.

CLEANING AND MAINTENANCE
The outside of the device should be cleaned periodically to remove contaminants such as dust etc. The lenses, in particular, should be clean to ensure that light will be emitted at maximum brightness.

1. Disconnect the device from power and allow it to cool before cleaning.
2. Clean the surface with a soft lint-free and moistened cloth. Never use alcohol or solvents as these may damage the surface. Make sure that no liquids can enter the device.
3. The device must be dry before reapplying power.

There are no serviceable parts inside. Do not open the housing. Do not try to repair the device by yourself as this may result in damage. Maintenance and service  operations are only to be carried out by authorized dealers. Should you need any spare parts, please use genuine parts. Should you have further questions, please contact your dealer.

PROTECTING THE ENVIRONMENT

Disposal of old equipment
When to be definitively put out of operation, take the product to a local recycling plant for a disposal which is not harmful to the environment. Devices marked with this symbol must not be disposed of as household waste. Contact your retailer or local authorities for more information. Remove any inserted batteries and dispose of them separately from the product.

You as the end user are required by law (Battery Ordinance) to return all used batteries/ rechargeable batteries. Disposing of them in the household waste is prohibited. You may return your used batteries free of charge to collection points in your municipality and anywhere where batteries/rechargeable batteries are sold. By disposing of used devices and batteries correctly, you contribute to the protection of the environment.

TECHNICAL SPECIFICATIONS

supply cord with safety plug
Lamp type:| LED lamp| LED lamp
LED:| 9 x high-power 3 W ultra violet (UV)| 18 x high-power 3 W ultra violet (UV)
Cooling:| Passive convection| Passive convection
Control:| Plug and play| Plug and play
Beam angle (1/2 peak):| 80°| 80°
Wavelength:| 400 nm| 400 nm
Housing color:| Black| Black
Material:| Aluminum| Aluminum
Dimensions:| Width: 50 cm| Width: 1 m
Depth: 4.5 cm| Depth: 4.5 cm
Height: 12.5 cm| Height: 12.5 cm
Weight:| 1.1 kg| 1.9 kg
Noise classification:| Class 0 (no noise at all)| Class 0 (no noise at all)
| |
Mounting bracket| |
Pieces:| 2 pcs.| 2 pcs.
Mounting holes:| 10.5 mm 0 diameter| 10.5 mm 0 diameter
Material:| Metal| Metal
Color:| Black| Black

All information is subject to change without prior notice. © 20.05.2022

Accessories

Eurolite is a brand of Steinigke Showtechnic
GmbH I Andreas-Bauer-Str. 5 I 97297
Waldbüttelbrunn Germany
D00139052 Version 1.0 Publ. 20/05/2022
Das neueste Update dieser Bedienungsanleitung finden Sie im Internet unter:
You can find the latest update of this user manual in the Internet under:
www.eurolite.de

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>