eurolite SB-1100B Power Distributor User Manual

eurolite SB-1100B Power Distributor

For your own safety, please read this user manual carefully before you initially start-up.

Every person involved with the installation, operation and maintenance of this device has to

• be qualified
• follow the instructions of this manual
• consider this manual to be part of the total product
• keep this manual for the entire service life of the product
• pass this manual on to every further owner or user of the product
• download the latest version of the user manual from the Internet

INTRODUCTION

Thank you for having chosen a EUROLITE SB-1100B. If you follow the instructions given in this manual, we
are sure that you will enjoy this device for a long period of time.
Unpack your SB-1100B.

Before you initially start-up, please make sure that there are no transport damages. Should there be any, do
not take the device into operation and immediately consult your dealer.

SAFETY INSTRUCTIONS

Be careful with your operations. With a dangerous voltage you can suffer a dangerous electric shock when touching the wires!
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual.

Important:
Damages caused by the disregard of this user manual are not subject to warranty. The dealer will not accept liability for any resulting defects or problems.
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature.
Please make sure that there are no obvious transport damages. Should you notice any damages on the A/C connection cable or on the casing, do not take the device into operation and immediately consult your local dealer.

This device falls under protection class I. The CEE plug must only be plugged into a CEE outlet. The voltage and frequency must exactly be the same as stated on the device. Wrong voltages or power outlets can lead to the destruction of the device and to mortal electrical shock.

Always plug in the power supply CEE plug last. The power plug must always be inserted without force. Make sure that the plug is tightly connected with the outlet.

Never let the power cord come into contact with other cables! Handle the power cord and all connections with the mains with particular caution! Never touch them with wet hands, as this could lead to mortal electrical shock.
Never modify, bend, strain mechanically, put pressure on, pull or heat up the power cord. Never operate next to sources of heat or cold. Disregard can lead to power cord damages, fire or mortal electrical shock.
The cable insert or the female part in the device must never be strained. There must always be sufficient cable to the device. Otherwise, the cable may be damaged which may lead to mortal damage.

Make sure that the power cord is never crimped or damaged by sharp edges. Check the device and the power-cord from time to time.
If extension cords are used, make sure that the core diameter is sufficient for the required power consumption of the device. All warnings concerning the power cords are also valid for possible extension cords.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power cord by the plug. Never pull out the plug by tugging the power cord. Otherwise, the cable or plug can be damaged leading to mortal electrical shock. If the power plug or the power switch is not accessible, the device must be disconnected via the mains.

If the power plug or the device is dusty, the device must be taken out of operation, disconnected and then be cleaned with a dry cloth. Dust can reduce the insulation which may lead to mortal electrical shock. More severe dirt in and at the device should only be removed by a specialist.
There must never enter any liquid into power outlets, extension cords or any holes in the housing of the device. If you suppose that also a minimal amount of liquid may have entered the device, it must immediately be disconnected. This is also valid, if the device was exposed to high humidity. Also if the device is still running, the device must be checked by a specialist if the liquid has reduced any insulation. Reduced insulation can cause mortal electrical shock.
There must never be any objects entering into the device. This is especially valid for metal parts. If any metal parts like staples or coarse metal chips enter into the device, the device must be taken out of operation and disconnected immediately. Malfunction or short circuits caused by metal parts may cause mortal injuries.
The total weight of the installation (=total weight of all individual parts) must never exceed the maximum load of the installation area.
Keep away children and amateurs!
Never leave this device running unattended.

OPERATING DETERMINATIONS

This device is a power distributor for supplying current to other devices.
This product is only allowed to be operated with an alternating voltage of 380-400 V, 50 Hz and was designed for indoor use only.
This device is designed for mobile use via a lighting stand and for permanent installations via trussing system.
The maximum power consumption of this device must never be exceeded.

When choosing the installation spot, please make sure that the device is not exposed to extreme heat, moisture or dust. There should not be any cables lying around. You endanger your own and the safety of others!
This device must never be operated or stockpiled in surroundings where splash water, rain, moisture or fog may harm the device. Moisture or very high humidity can reduce the insulation and lead to mortal electrical shocks. When using smoke machines, make sure that the device is never exposed to the direct smoke jet and is installed in a distance of 0.5 meters between smoke machine and device.
The ambient temperature must always be between -5° C and +45° C. Keep away from direct insulation (particularly in cars) and heaters.
The relative humidity must not exceed 50 % with an ambient temperature of 45° C.
This device must only be operated in an altitude between -20 and 2000 m over NN.
The ambient contamination must never exceed level 1 and must not be conducting, only dry.
Never use the device during thunderstorms. Overvoltage could destroy the device. Always disconnect the device during thunderstorms.
Make sure that the area below the installation place is blocked when rigging, derigging or servicing the fixture.
Operate the device only after having familiarized with its functions. Do not permit operation by persons not qualified for operating the device. Most damages are the result of unprofessional operation!
Never use solvents or aggressive detergents in order to clean the device! Rather use a soft and damp cloth.
Please use the original packaging if the device is to be transported.
Inspection deadlines according to DGUV-V3 for electrical resources must be complied with.
Please consider that unauthorized modifications on the device are forbidden due to safety reasons!
If this device will be operated in any way different to the one described in this manual, the product may suffer damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like shortcircuit, burns, electric shock, crash etc.

WEEE Directive
When to be definitively put out of operation, take the unit(s) to a local recycling plant for a disposal which is not harmful to the environment. Do not dispose of as municipal waste. Contact your retailer or local authorities for more information.

DESCRIPTION OF THE DEVICE

Product features

Practical 32A distributor in 19″ housing

• Specially designed for larger distribution needs
• 3U necessary for installation
• 32A three phase current input via power cable and plug
• 32A three-phase current output via mounted plug, secured on the back panel by a fault current circuit breaker
• The entire distributor is secured via a Type B 40A/0.03A 4-pol fault current circuit breaker
• 2 mounted CEE sockets with 16A on the front panel are secured via 2 x 16A fuse blocks
• Control lamps indicate each phase
• 6 safety sockets on the housing back (2 per phase)
• Each pair of safety sockets feature fuse protection via 16A automatic circuit breakers
• With earthing screw in order to ground a rig if necessary

Device view 1

1. 19″ housing

2. Phase 3 power outputs

3. Phase 2 power outputs

4. Phase 1 power outputs

5. 32A three-phase-current output socket

6. 32A three-phase-current input plug
   Device view 2

7. Phase control lamps

8. Fault-current circuit breaker

9. 2 x 16A circuit breaker for three phase current

10. Circuit breakers for power distribution safety sockets

11. 2 x 16A three-phase-current output socket

INSTALLATION

DANGER TO LIFE!
Please consider the DIN 15560 and the respective national norms during the installation! The installation must only be carried out by an authorized dealer!
The operator has to make sure that safety-relating and machine-technical installations are approved by an expert before taking into operation for the first time and after changes before taking into operation another time.
The operator has to make sure that safety-relating and machine-technical installations are approved by an expert after every four year in the course of an acceptance test.
The operator has to make sure that safety-relating and machine-technical installations are approved by a skilled person once a year.

Procedure:
The installation should be attached outside areas where persons may walk by or be seated.

Rack installation
This 19“ distributor 32A is built for 19“racks/steel cabinets (483 mm). The rack you use should be a doubledoor- rack where you can open the front panel and the rear panel. The rack should be provided with a cooling fan. When mounting the 19“ distributor into the rack, please make sure that there is enough space around
the device so that the heated air can be passed on. Steady overheating will damage your device.
You can fix the 19“ distributor with four M6 screws in the rack.
Be careful when mounting the 19“ distributor into the rack. Put the heaviest devices into the lower part of the rack.

Connections

Connection with the mains
Connect the device to the mains with the CEE plug.
The earth has to be connected!
If the device will be directly connected with the local power supply network, a disconnection switch with a minimum opening of 3 mm at every pole has to be included in the permanent electrical installation.

Outputs
Output is via six safety sockets, two 16A three-phase-current output sockets, and one 32A three-phase current output socket.
Connect your loads via the output sockets. The maximum load per channel is 3,680 W (resistive), 11040 W, and 22080 W respectively. Please note that the maximum current must never be exceeded.

DANGER TO LIFE!
Before taking into operation for the first time, the installation has to be approved by an expert!

CLEANING AND MAINTENANCE

The operator has to make sure that safety-relating and machine-technical installations are inspected by an expert after every four years in the course of an acceptance test.
The operator has to make sure that safety-relating and machine-technical installations are inspected by a skilled person once a year.
The following points have to be considered during the inspection:

1. All screws used for installing the devices or parts of the device have to be tightly connected and must not be corroded.
2. The electric power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments. Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed.
   Disconnect from mains before starting maintenance operation!

DANGER TO LIFE!
We recommend a frequent cleaning of the device. Please use a moist, lint-free cloth. Never use alcohol or solvents!
There are no serviceable parts inside the device. Maintenance and service operations are only to be carried out by authorized dealers.
Should you need any spare parts, please use genuine parts.

The examination intervals for mobile electrical devices (German DGUV-V3) must be kept.
The operator has to make sure that the electrical devices are examined by an electrician before taking into operation for the first time and after changes before taking into operation another time.

Electrical devices must only be taken into operation in a perfect condition and must be kept this way.
For keeping the perfect condition, electrical devices must repeatedly be approved in accordance with the instructions given in the electro-technical guidelines.
A qualified electrician is responsible for the correct examinations.
Mobile electrical devices, extension cords with plugs, power cables with plugs and mobile cables with plugs and permanent installation must be approved by an expert every three months.
Should you have further questions, please contact your dealer.

TECHNICAL SPECIFICATIONS

Power output:

| 1 x CEE 32A 5-pol (F) recessed mounting Bypass
6 x Safety contact (F), hinged lid mounting version fused
2 x CEE 16A 5-pol (F) recessed mounting fused

Protection:

| 1 x fault-current circuit breaker (FI) Type B 40A/0,03A 4-pol
2 x circuit breaker C 16A 3-pol
3 x circuit breaker C 16A 1-pol
Phase status display:| 3
Housing design:| (19″) 48.3 cm rack installation 3 U

Dimensions:

| Width: 48.3 cm
Depth: 29.5 cm
Height: 13.35 cm
Weight:| 6.05 kg

All information is subject to change without prior notice. © 10.06.2022

Eurolite is a brand of Steinigke Showtechnic GmbH I Andreas-Bauer-Str. 5 I 97297 Waldbüttelbrunn Germany
D00139830 Version 1.0 Publ. 10/06/2022

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>