EUROLITE LED CBB-4 COB RGB Bar Light User Manual

LED CBB-4
COB RGB Bar User Manual
LED CBB-4 COB RGB 4x15W Bar

LED CBB-4 COB RGB Bar Light

DANGER! Electric shock caused by short-circuit
Be careful with your operations. With a dangerous voltage you can suffer a dangerous electric shock when touching the wires. Never open the housing. Keep the device away from rain and moisture.
Please read these instructions carefully before using the product. They contain important information for the correct use of the product.
Every person involved with the installation, operation and maintenance of this device has to

• be qualified.
• follow the instructions of this manual
• consider this manual to be part of the total product
• keep this manual for the entire service life of the product
• pass this manual on to every further owner or user of the product
• download the latest version of the user manual from the Internet

INTRODUCTION

Thank you for having chosen one of our products. If you follow the instructions given in this manual, we are sure that you will enjoy this device for a long period of time.
Product features
LED light effect bar with RGB color mixing, incl. IR remote control

• 4 high-power 30 W RGB LEDs (COB)
• Auto, music, master/slave and DMX mode
• Built-in auto and music show programs
• Direct color selection for 19 preset colors
• Stepless RGBW color blend, color change, color fade, dimmer and strobe effect
• Flicker-free projection
• Addressing and setting via control panel with 4-digit LED display
• Convenient wireless control via included IR remote control EUROLITE IR-7
• Sound-control via built-in microphone with adjustable microphone sensitivity
• DMX512 control possible via any commercial DMX controller
• 3, 5, 12, 15 or 19 DMX channels selectable for various applications
• Swivel mounting bracket
• Feed-through output allows to power up to 8 devices

SAFETY INSTRUCTIONS

WARNING!
Please read the safety warnings carefully and only use the product as describe in this manual to avoid accidental injury or damage.
Intended use

• This device is an LED projector for creating decorative lighting effects. This device is designed for professional use in the field of event technology, e.g. on stage. It is not suitable for household lighting.
• Only use the device according to the instructions given herein. Damages due to failure to follow these operating instructions will void the warranty! We do not assume any liability for any resulting damage.
• We do not assume any liability for material and personal damage caused by improper use or noncompliance with the  safety instructions. In such  cases, the warranty/guarantee will be  null and void.
•   Unauthorized rebuilds or modifications of  the device are not permitted for reasons  of safety and render the warranty invalid.

Danger due to electricity

• The device is suitable for indoor use only. Do not use it outdoors. Never expose it to rain or moisture. Do not store it in rooms exposed to moisture.
• To reduce the risk of electric shock, do not open any part of the device. There are no serviceable parts inside the device.
• Only connect the device to a properly installed mains outlet. The outlet must be protected by residual current breaker (RCD). The voltage and frequency must exactly be the same as stated on the device. If the mains cable is equipped with an earthing contact, then it must be connected to an outlet with a protective ground. Never defeat the protective ground of a mains cable. Failure to do so could result in damage to the device and possibly injure the user.
• The mains outlet must be easily accessible so that you can unplug the device quickly if need be.
• Never touch the mains plug with wet or damp hands. There is the risk of potentially fatal electric shock.
• The mains cable must not be bent or squeezed. Keep it away from hot surfaces or sharp edges.
• Never pull the mains cable to disconnect the mains plug from the mains outlet, always seize the plug.
• Unplug the device during lighting storms, when unused for long periods of time or before cleaning.
• Do not expose the device to any high temperatures, direct sunlight, dripping or splashing water, strong vibrations or heavy mechanical stress.
• Do not place any objects filled with liquids on the device.
• Do not place any open sources of fire, such as burning candles, on or directly next to the device.
• Make sure that objects cannot fall into the device, in particular metal parts.
• Only have repairs to the device or its mains cable carried out by qualified service personnel. Repairs are required when the device or the mains cable is visibly damaged, liquid has been spilled or objects have fallen into the device; when the device has been exposed to rain or moisture, has been dropped or malfunctions occur.
• Cleaning of the device is limited to the surface. Make sure that moisture does not come into contact with any areas of the terminal connections or mains voltage control parts. Only wipe off the product with a soft lint-free and moistened cloth. Never use solvents or aggressive detergents.

Danger to children and people with restricted abilities

• This product is not a toy. Keep it out of the reach of children and pets. Do not leave packaging material lying around carelessly. Never leave this device running unattended.
• This device may be used only by persons with sufficient physical, sensorial, and intellectual abilities and having corresponding knowledge and experience. Other persons may use this device only if they are supervised or instructed by a person who is responsible for their safety.

Warning – risk of burns and fire

• The admissible ambient temperature range (Ta) is -5 to +45°C. Do not operate the device outside of this temperature range.
• The housing temperature (Tc) can be up to 55°C during use. Avoid contact by persons and materials.
• Do not illuminate surfaces within 10 cm of the device. This value is indicated on the device by the symbol.
• Do not use the device near highly flammable materials. Always place the device at a location where sufficient air circulation is ensured. Leave 50 cm of free space around the device. Never cover the air vents of the housing.
• Only operate the device in moderate climate, never in tropical climate.

Warning – risk of injuries

• Do not look directly at the light source. Persons with light-sensitive epilepsy may suffer from epileptic seizures or fall unconscious.
• Make sure that the product is set up or installed safely and expertly and prevented from falling down. Comply with the standards and rules that apply in your country, in particular EN 60593-2-17.
• If you lack the qualification, do not attempt the installation yourself, but instead use a professional installer. Improper installation can result in bodily injury and or damage to property.
• The manufacturer cannot be made liable for damages caused by incorrect installations or insufficient safety precautions.
• For overhead use, always secure the device with a secondary safety attachment such as a safety bond or safety net.
• Make sure that the area below the installation place is blocked when rigging, derigging or servicing the device.
• For commercial use the country-specific accident prevention regulations of the government safety organization for electrical facilities must be complied with at all times.

Caution – material damage

• This device must not be connected to the mains voltage by means of a dimmer.
• Lighting effects are not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects.
• Never switch the device on and off at short intervals. This will considerably reduce the service life of the device.
• If the device has been exposed to drastic temperature fluctuation, do not switch it on immediately. The resulting condensation may destroy the device. Allow the device to reach room temperature before connecting it. Wait until the condensation has evaporated.
• Please use the original packaging to protect the device against vibration, dust and moisture during transportation or storage.
• If a serial number label is affixed to the device, do not remove the label as this would make the guarantee void.

About batteries

• Do not try to short-circuit, recharge, disassemble or heat batteries (danger of explosion!).
• Remove the batteries if the device is not used for a longer period of time.
• Damaged/leaking batteries may cause harm to your skin–use safety gloves.

DESCRIPTION OF THE DEVICE

(1) RGB LED 1
(2) RGB LED 2
(3) RGB LED 3
(4) RGB LED 4
(5) Infrared sensor for the remote control
(6) Fixation screws
(7) Power feed-through output| (8) Fuse holder
(9) Power input
(10) DMX input
(11) DMX output
(12) LED display and operating buttons
(13) Safety eyelet
(14) Microphone
(15) Mounting bracket
---|---

INSTALLATION
WARNING! Risk of injury caused by falling objects
Devices in overhead installations may cause severe injuries when crashing down. Make sure that the device is installed securely and cannot fall down. The installation must be carried out by a specialist who is familiar with the hazards and the relevant regulations.
The device may be placed on the floor via its bracket or fastened to a truss or similar rigging structure. The device must never be fixed swinging freely in the room.

1. The rigging structure must support at least 10 times the weight of all fixtures to be installed on it.
2. Block access below the work area and work from a stable platform when installing the device.
3. Use rigging hardware that is compatible with the structure and capable of bearing the weight of the device. Please refer to the “Accessories” section for a list of suitable rigging hardware.
4. Secure the device with a safety bond or other secondary attachment. This secondary safety attachment must be sufficiently dimensioned in accordance with the latest industrial safety regulations and constructed in a way that no part of the installation can fall down if the main attachment fails. Pull the safety bond through the safety eyelet and fasten it in such a way that, in the event of a fall, the maximum drop distance of the device will not exceed 20 cm.
5. To align the device, release the fixation screws at the mounting bracket, adjust the desired inclination angle and retighten the fixation screws.
6. After installation, the device requires inspections periodically to prevent the possibility of rot, deformation and looseness.

CONNECTIONS
DMX512 control
A DMX512 data link is required in order to control the device via DMX. The device provides 3-pin XLR connectors for DMX connection.

1. Connect the output of your DMX controller to the DMX input DMX IN of the light set with a DMX cable.
2. Connect the DMX output DMX OUT of the light set to the DMX input of the next unit in the chain. Always connect one output to the input of the next unit until all units are connected.
3. At the last unit, the DMX cable has to be terminated. Plug the terminator with a 120 Ω resistor between Signal (–) and Signal (+) in the DMX output of the last unit.
4. If the cable length exceeds 300 m or the number of DMX devices is greater than 32, it is recommended to insert a DMX level amplifier to ensure proper data transmission.

XLR connection:

Connection to the mains
The device uses an auto-range power supply that accepts input voltages between 100 und 240 volts.

1. Connect the device via the mains cable to a grounded mains socket. Thus the unit is switched on.
2. To switch off the unit, disconnect the power plug.
3. Do not connect the unit to the mains voltage via a dimmer. For a more convenient operation, use a mains outlet which is switchable.
   Power supply of further devices
   The jack POWER OUT allows for power supply of further devices. To interconnect several devices, connect the jack POWER OUT to the input POWER IN of the next unit until all units are connected. Matching power cables with IEC plugs and IEC inline jacks are available as accessories. A maximum of 8 units can be linked.

OPERATION

After connecting the device to the mains it is ready for operation. The display indicates the last operating mode. The operating modes can be selected by means of the display and the control buttons. All settings remain stored even if the device is disconnected from the mains. The device can be operated in stand-alone mode via the control board and the EUROLITE IR-7 remote control or in DMX-controlled mode via any commercial DMX controller.
Menu structure

Mode| Display Function
---|---
DMX mode| Addr| 19CH| d001-512| 19-channel mode and start address
15CH| d001-512| 15-channel mode and start address
12CH| d001-512| 12-channel mode and start address
5CH| d001-512| 5-channel mode and start address
3CH| d001-512| 3-channel mode and start address
Preset colors| Stat| S 01-19| Constant lighting in one of 19 colors
__

Automatic mode

| __

Auto

| Au – 1| Program 1: color fade
Au – 2| Program 2: color change
Sound control| Soun| So – 1| Program 1: color fade
So – 2| Program 2: color change
Running speed in automatic mode| SPEE| SP 1-9| Program running speed slow > fast
Microphone sensitivity for sound control| SEnS| SE 1-9| Microphone sensitivity low > high
Individual color mix| Colo| r000-255| Red 0-100%
g000-255| Green 0-100%
b000-255| Blue 0-100%
__**Dimmer| __ diMM| dI 1-dI 9| Total brightness (Stat, Auto, Soun, and Colo modes) dark > bright
Sound control silent scene| SILE| on| LEDs off if there is no music signal
oFF| LEDs remain on if there is no music signal
Slave mode| SLAU| SLAU| Slave mode
IR remote control**| InFr| on| IR remote control on
oFF| IR remote control off

Stand-alone mode
Automatic mode
In automatic mode, 2 show programs are available that run at an adjustable speed.

1. Press the MENU button so many times until Auto is indicated in the display. Confirm with the ENTER button. Use the buttons UP and DOWN to select the desired show program. Confirm with the ENTER button.
2. Press the MENU button so many times until SPEE is indicated in the display. Confirm with the ENTER button. Use the buttons UP and DOWN to adjust the running speed of the program from SP 1 (slow) to SP 9 (fast). Confirm with the ENTER button.

Sound control
Via the integrated microphone the unit can perfectly reproduce the show programs to the rhythm of the music (sufficient bass provided).

1. Press the MENU button so many times until Soun is indicated in the display. Confirm with the ENTERbutton. Use the buttons UP and DOWN to select the desired show program. Confirm with the ENTER button.
2. Press the MENU button so many times until SEnS is indicated in the display. Confirm with the ENTER button. Use the buttons UP and DOWN to Adjust the microphone sensitivity to the volume of the music (SE 1 = low, SE 9 = high).
3. If you enable the silent scene mode (on setting) in menu item SILE, the LEDs will be switched off if the volume is too low or if there is no sufficient bass beat. If you disable this mode (off setting) the LEDs remain on during periods without music.

Preset colors
In the Stat mode the device will constantly emit one of 19 preset colors.

1. Press the MENU button so many times until Stat is indicated in the display. Confirm with the ENTER button.
2. Use the buttons UP and DOWN to adjust the desired color. Confirm with the ENTER button.

Individual color mix
In the color mode Colo each of the quadcolor LEDs can be individually adjusted for brightness. The device will constantly emit the color adjusted.

1. Press the MENU so many times until Colo is indicated in the display. Confirm with the ENTER button.
2. Now the display indicates the letter R for the color and the corresponding brightness value. Use the buttons UP and DOWN to adjust the desired brightness.
3. Confirm with the ENTER button. Now the color green can be adjusted; then blue and white.

Total brightness
Menu diMM allows adjusting the total brightness for all stand-alone operating modes: Stat, Auto, Soun, Colo.

1.  Press the MENU button so many times until diMM is indicated in the display. Confirm with the ENTER button.
2. Use the buttons UP and DOWN to adjust the desired brightness (dI 1 = dark, dI 9 = bright). Confirm with the ENTER button.

Interconnecting several devices (master/slave operation)
Several devices may be interconnected (max. 32). Then all slave units can be synchronized and controlled with the master unit without the need for a DMX controller. The devices must be set to the corresponding operating modes.

1. Configure all slave units before connecting the master unit: Press the MENU button so many times until SLAU is indicated in the display. Confirm with the ENTER button.
2. Connect the DMX output of the master unit to the DMX input of the first slave unit. Then connect the DMX output of the first slave unit to the DMX input of the second slave unit, etc. until all units have been connected in a chain. Make sure the master unit is the first in the chain. Do not connect a DMX controller to the DMX input of the master unit.
3. Set the master unit to the desired operating mode. The interconnected devices will now operate in sync.

Remote control IR-7
The device must be activated for remote control. For this, set menu item InFr to on. When actuating a button, always direct the remote control towards the sensor. There must be no obstacles between remote control and the sensor.

setting with (+)/(‒)
SPEED| Running speed in automatic mode; setting with (+)/(‒)
SENSITIVITY| Microphone sensitivity; setting with (+)/(‒)
DMX| DMX mode
MANUAL| Color mode; select colors with R/G/B and (+)/(‒)
FADE| Color fade mode
1-9| Total brightness; 1 = dark, 9 = bright

Notes:

• The remote control is supplied with a battery inserted. An insulating foil between the battery and the battery contacts prevents the battery from being discharged during storage. Prior to the first operation remove the foil from the battery support on the rear side of the remote control. Otherwise operation of the remote control is not possible.
• If the range of the remote control decreases, replace the battery. For this purpose, on the rear side of the remote control press the small bar with the groove to the right and at the same time remove the battery support. For operation, one 3 V button cell type CR 2025 is required. When inserting, pay attention that the positive pole of the button cell shows upwards in the support.
• Remove the battery from the remote control as a precaution if the device is not used for a longer period of time.

DMX operation
Setting the number of DMX channels and the DMX starting address
For operation with a controller with DMX512 protocol, the device is equipped with 19 control channels.
However, it can also be switched to a mode with 3, 5, 12 or 15 channels if different functions are required. To be able to operate the device with a DMX controller, the DMX starting address must be set for the first DMX channel. The starting address depends upon which DMX controller is being used. Please refer to the controller’s documentation.

1. Press the MENU button so many times until Addr is indicated in the display. Confirm with the ENTER button.
2. The display indicates 3 CH (3 DMX channels), 5 CH (5 DMX channels), 12 CH (12 DMX channels), 15 CH (15 DMX channels) or 19 CH (19 DMX channels). Use the buttons UP and DOWN to select the desired number of DMX channels. Confirm with the ENTER button.
3. Now the display indicates the menu item for the DMX start address d***. Use the buttons UP and DOWN to set the address. Confirm with the ENTER button.
4. A dot will light up when DMX signals are being received. If no control signals are available, the dot be flashing
   Note: Please make sure that you do not have any overlapping channels in order to control each device correctly and independently from any other fixture on the DMX chain. If several devices are addressed similarly, they will work synchronically. Functions in DMX mode

3-channel mode

5-channel mode

4

Master dimmer

| 000 – 255| Total brightness 0-100 %
5

Sound control/ Strobe

| 000 – 000| No function
001 – 005| Sound-controlled mode (7 colors)
006 – 010| No function
011 – 255| Strobe with increasing speed

12-channel mode

LED 1

2| 000 – 255| Green 0-100%
3| 000 – 255| Blue 0-100%
4| 000 – 255| Red 0-100%| ****

LED 2

5| 000 – 255| Green 0-100%
6| 000 – 255| Blue 0-100%
7| 000 – 255| Red 0-100%| ****

LED 3

8| 000 – 255| Green 0-100%
9| 000 – 255| Blue 0-100%
10| 000 – 255| Red 0-100%| LED 4
11| 000 – 255| Green 0-100%
12| 000 – 255| Blue 0-100%

15-channel mode

1

Internal programs, sound control

| 000 – 009| No function|
010 – 029| Program 1
030 – 049| Program 2
050 – 069| Program 3
070 – 089| Program 4
090 – 109| Program 5
110 – 129| Program 6
130 – 149| Program 7
150 – 169| Program 8
170 – 189| Program 9
190 – 209| Program 10
210 – 229| Program 11
230 – 249| Automatic mode
250 – 255| Sound-controlled mode
2

Master dimmer

| 000 – 255| Total brightness 0-100%
3

Strobe

| 000 – 009| No function
010 – 255| Strobe with increasing speed 0-100%
4| 000 – 255| Red 0-100%| ****

LED 1

5| 000 – 255| Green 0-100%
6| 000 – 255| Blue 0-100%
7| 000 – 255| Red 0-100%| ****

LED 2

8| 000 – 255| Green 0-100%
9| 000 – 255| Blue 0-100%
10| 000 – 255| Red 0-100%| ****

LED 3

11| 000 – 255| Green 0-100%
12| 000 – 255| Blue 0-100%
13| 000 – 255| Red 0-100%| ****

LED 4

14| 000 – 255| Green 0-100%
15| 000 – 255| Blue 0-100%

19-channel mode

1

Master dimmer

| 000 – 255| Total brightness 0-100%|
2

Strobe

| 000 – 255| Strobe with increasing speed 0-100%
3| 000 – 255| Red 0-100%| ****

LED 1

4| 000 – 255| Green 0-100%
5| 000 – 255| Blue 0-100%
6| 000 – 255| Red 0-100%| ****

LED 2

7| 000 – 255| Green 0-100%
8| 000 – 255| Blue 0-100%
9| 000 – 255| Red 0-100%| ****

LED 3

10| 000 – 255| Green 0-100%
11| 000 – 255| Blue 0-100%
12| 000 – 255| Red 0-100%| ****

LED 4

13| 000 – 255| Green 0-100%
14| 000 – 255| Blue 0-100%

15 – 18

Preset colors

| 000 – 009| No function|
010 – 019| Red
020 – 029| Green
030 – 039| Blue
040 – 049| Yellow
050 – 059| Magenta
060 – 069| Cyan
070 – 079| Dark orange
080 – 089| Green yellow
090 – 099| Salmon
100 – 109| Turquoise
110 – 119| Light green
120 – 129| Orange
130 – 139| Straw
140 – 149| Lavender
150 – 159| Light blue
160 – 169| Dark blue
170 – 179| Pink
180 – 189| Cool white
190 – 255| Warm white

19

| 000 – 009| No function
010 – 069| Automatic color fade with increasing speed
070 – 129| Automatic color change with increasing speed
130 – 189| Sound-controlled color fade with increasing speed
190 – 255| Sound-controlled color change with increasing speed

CLEANING AND MAINTENANCE

The outside of the device should be cleaned periodically to remove contaminants such as dust etc. The lenses, in particular, should be clean to ensure that light will be emitted at maximum brightness.

1. Disconnect the device from power and allow it to cool before cleaning.
2. Clean the surface with a soft lint-free and moistened cloth. Never use alcohol or solvents as these may damage the surface. Make sure that no liquids can enter the device.
3. The device must be dry before reapplying power.
   There are no serviceable parts inside. Do not open the housing. Do not try to repair the device by yourself as this may result in damage. Maintenance and service operations are only to be carried out by authorized dealers. Should you need any spare parts, please use genuine parts. Should you have further questions, please contact your dealer.

Replacing the fuse
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.

1. Disconnect the device from power and allow it to cool.
2. Open the fuse holder of the mains connection with a fitting screwdriver.
3. Remove the old fuse from the fuse holder and replace it with a new fuse.
4. Carefully push the fuse holder back into its position before reapplying power.

PROTECTING THE ENVIRONMENT

Disposal of old equipment
When to be definitively put out of operation, take the product to a local recycling plant for a disposal which is not harmful to the environment. Devices marked with this symbol must not be disposed of as household waste. Contact your retailer or local authorities for more information. Remove any inserted batteries and dispose of them separately from the product.
You as the end user are required by law (Battery Ordinance) to return all used batteries/ rechargeable batteries. Disposing of them in the household waste is prohibited. You may return your used batteries free of charge to collection points in your municipality and anywhere where  batteries/rechargeable batteries are sold. By disposing of used devices and batteries correctly,you contribute to the protection of the environment.

TECHNICAL SPECIFICATIONS

Accessories

All information is subject to change without prior notice. © 27.05.202100110552, Version 1.1
Eurolite is a brand of Steinigke Showtechnic GmbH · Andreas-Bauer-Str. 5 · 97297 Waldbüttelbrunn Germany D00110552 Version 1.1 Publ. 27/05/2021

LED CBB-4 COB RGB Bar
LED light effect bar with RGB color mixing, incl. IR remote control

No. 51930278
www.eurolite.de
This user manual is valid for the article number: 51930278
You can find the latest update of this user manual in the Internet under:
www.eurolite.de

References

• Eurolite: Ihre Experten für Licht - Hersteller von Lichteffekten

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>