zap ACC351-352, ACC361-362 Cordless Exit Buttons User Guide
- June 8, 2024
- zap
Table of Contents
zap ACC351-352, ACC361-362 Cordless Exit Buttons
ACC351-352, ACC361-362 – Quick Start Guide
Exit Buttons
This guide covers the hygienic and convenient range of contactless buttons. These buttons can be activated without touching them to release the door, simply put your hand near to the button to unlock it. The sensitivity can be adjusted to detect at different ranges to suit the installation.
User Information
- There are no user serviceable parts, opening or attempting to repair the product will void the warranty.
- Do not install or use the device if the wires connected are damaged or have been subjected to water ingress.
- Shut off all power to the access control system before wiring this device.
- Maintain a clean and safe environment at all times.
Definition
NO (Normally Open) – This is a contact which remains open (as default)
until activated, during the “active” state the contact provides a closed
circuit and starts conducting.
NC (Normally Closed) – Is the opposite of a NO contact. The contact will
remain closed (as default) until activated, during the “active” state the
circuit breaks and stops current flow.
Setup Example
Exit buttons are used in access control systems to provide a momentary contact signal to the access controller to open a magnetic lock. This example shows a “Fail-safe” scenario. When the exit button is activated the access control power supply then releases power from the lock, and if power is lost then the lock also releases. Wire in NO or NC depending on the access controller used and also on the required state of the lock during a “Failsafe” or “Fail- secure” scenario.
Connections – ACC351-352, ACC361-362
- For operation with a door access control panel and lock, the exit button is wired with NC or NO and COM.
- A permanent DC 12-24V supply is required to operate the contactless exit buttons (not supplied with the product).
Sensitivity & Time Delay Adjustment
Troubleshooting
- If the exit button is not activating the lock then there is likely a shorted wire, open circuit or some other failed device in the circuit.
- To identify where the fault is, each wired connection in the circuit needs to be tested; working from the push button progress through, including the keypad, the access controller, power supply and the magnetic lock.
- If the fault is with the access control button then check the connection wires for continuity and for trapped wires. Check for water ingress on the wired connections. Check the polarity in the power connections and ensure the connections are connected to the proper terminals.
Specification
| ACC351 | ACC352 | ACC361 | ACC362 | |
|---|---|---|---|---|
| Construction | Stainless Steel | Stainless Steel & Plastic | Plastic | Alloy |
Detection
Range
| 50 – 200mm| 80 – 420 mm| 90 – 300mm| 80 – 200mm
IP- Rating| IP68| Internal Use| IP68
Latch| 1-30 secs| Mimic| 1-30 secs| 1-25 secs
LED Colour| Idle-Blue/ Active-Green| Idle-Blue/ Active-
Green
| Idle-Red/ Active-Green| Idle-Blue/ Active-
Green
Rating| 2A @12V DC| 3A @ 12V DC| 2A @ 24V DC
Terminals| NO/ NC/ Common/ 12-24V DC/ GND (Wires)
Voltage| 12-24V DC
Dimensions| 86 x 86 x 20mm| 86 x 86 x 37mm| 86 x 86 x 20| 80 x 32 x 23mm
All specifications are approximate. System Q Ltd reserves the right to change product specifications or features without notice. Whilst every effort is made to ensure that these instructions are complete and accurate, System Q Ltd cannot be held responsible for any losses, no matter how they arise, from errors or omissions in these instructions, or the performance or non- performance of the equipment refered to.
This symbol indicates that equipment must not be mixed with general household
waste. For treatment, recovery and recycling please return to your local
designated
WEE/CG0783SS collection point as defined by your local
council.ZapCCTV.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>