zap ACC200-202 Slim and Compact Exit Button User Guide
- June 4, 2024
- zap
Table of Contents
zap ACC200-202 Slim and Compact Exit Button User Guide
Exit Buttons
This guide covers the slim exit buttons which are made from zinc alloy with a matt finish. Their slim footprint means they can fit most locations and come supplied with their own back box.
This guide also covers the compact exit buttons, just 53mmwide with a built-in back box. The options available also include the LED illuminated ACC253 model.
User Information
- There are no user serviceable parts, opening or attempting to repair the product will void the warranty.
- Do not install or use the device if the wires connected are damaged or have been subjected to water ingress.
- Shut off all power to the access control system before wiring this device.
- Maintain a clean and safe environment at all times.
Definition
NO (Normally Open) – This is a contact which remains open (as default)
until activated, during the “active” state the contact provides a closed
circuit and starts conducting. NC
(Normally Closed) – Is the opposite of a NO contact. The contact will
remain closed (as default) until activated, during the “active” state the
circuit breaks and stops current flow.
Setup Example
Exit buttons are used in access control systems to provide a momentary contact signal to the access controller to open a magnetic lock.
This example shows a “Fail-safe” scenario. When the exit button is pressed the access control power supply then releases power from the lock, and if power is lost then the lock also releases.
Wire in NO or NC depending on the access controller used and also on the required state of the lock during a “Fail-safe” or “Fail- secure” scenario.
Connections
Connections – ACC200
For operation with a door access control panel and lock, the exit button is
provided with NO/COM terminals.
Connections – ACC202, ACC250-252
For operation with a door access control panel and lock, the exit button
button is provided with NC or NO and COM connection wires.
Connections – ACC253
For operation with a door access control panel and lock, the exit button is
provided with NC or NO.
The ACC063 also has a built in blue LED which requires 12V DC (not supplied with the product).
Troubleshooting
If the exit button is not activating the lock then there is likely a shorted wire, open circuit or some other failed device in the circuit.
To identify where the fault is, each wired connection in the circuit needs to be tested; working from the push button progress through, including the keypad, the access controller, power supply and the magnetic lock.
If the fault is with the access control button then check the connection wires for continuity and for trapped wires. Check for water ingress on the wired connections. Check the polarity in the power connections and ensure the connections are connected to the proper terminals.
Specification
| ACC200 | ACC202 | ACC250-252 | ACC253 | |
|---|---|---|---|---|
| Construction | Zinc Alloy | Zinc Alloy | Zinc Allo | Zinc Alloy |
| Terminals | NO/Common (Screw Terminals) | NO/NC/Common (Wires) | NO/NC/Common | |
| (Wires) | NO/Common/ +12V DC/ GND (Wires) | |||
| Rating | 2A12V DC Max | 2A12V DC Max | 0.5-1A 12V DC Max | 0.5-1A 12V DC Max |
| LED Colour | ~ | ~ | ~ | Blue LED |
| Dimensions | 80 x 30 x 26mm | 93 x 35 x 28mm | 53 x 53 x28mm | 53 x 53 x28mm |
All specifications are approximate. System Q Ltd reserves the right to change product specifications or features without notice. Whilst every effort is made to ensure that these instructions are complete and accurate, System Q Ltd cannot be held responsible for any losses, no matter how they arise, from errors or omissions in these instructions, or the performance or non- performance of the equipment refered to.
This symbol indicates that equipment must not be mixed with general household waste. For treatment, recovery and recycling please return to your local designated WEE/CG0783SS collection point as defined by your local council.