Chacon 34036 Door-Window Opening Sensor User Manual

Chacon 34036 Door-Window Opening Sensor

WHAT IN THE BOX

Door/window opening sensor (x2)

• Rilevatore di apertura porte/finestre (x2)

Registering the guarantee
To register your warranty, fill in the online form at www.chacon.com/warranty

Product overview

1. LED indicator
2. Magnetic part

Introduction

Thank you for using this product.

• – Please read all instructions carefully before using the product.
• – Do not attempt to disassemble or repair the pro-duct yourself, as this will invalidate the warranty.
• – In order to use this product, you must have either a simple central unit with a remote control or a remote keypad, or a central unit with a code. (Compatible references: 34035, 34038, 34043, 34044, 34045, 34046, 34048)

Battery Installation: Door Opening Sensor

1. Using a crosshead screwdriver, remove the screw on the front of the opening detector
2. Slide the cover down to access the battery compartment.
3. Insert the battery, ensuring correct polarity (+/-)
4. Close the compartment with the cover and screw.

Link the detector with a central unit

1. Using a screwdriver, open the battery compart-ment of the main unit.
2. Press and hold the learn button until you hear a «beep». The unit enters pairing mode.
3. Separate the two parts of the opening detector to send a signal to the main unit. You will hear a «beep» sound to indicate that the pairing was successful.
4. To exit pairing mode, press and hold the learn button for 3 seconds. You will then hear a double «beep».

NOTE: A maximum of 32 transmitters can be paired to a main unit.

Alarm activation mode

Two methods of synchronisation:

• a) Associating the detector with a central unit with code: You just have to make the pre-registered code to activate or deactivate the alarm. (see corresponding manual)
• b) Associating the detector with a classic control panel + remote control: activate and deactivate the alarm using the «on» and «off» buttons on the remote control (see corresponding manual)

NOTE: This detector is compatible with the entire range. You can therefore combine it with any device while ensuring that you have at least one central alarm unit (motion detector with or without code, opening detector with code)

 Reset pairing

In order to reset your entire alarm, remove the batteries from your device. Then press and hold the learning button of your central unit. When you reinsert the batteries, you will hear two «beeps» indicating that the reset was successful.

Problem-solving

1. False alarms from the main unit

   • a) Check that there are no animals near the motion detector.
   • b) In hot weather, moving shadows may also activate the alarm. Also ensure that the detector is not installed near a radiator or heat source.
   • c) Check that there are no devices with strong electromagnetic fields near the door/window sensor. Strong electromagnetic fields can cause false alarms.

2. The main unit doesn’t receive a signal from the transmitter

   • a) Check if the pairing between the transmitter and the main unit was successful.
   • b) If pairing was successful, check the battery voltage of the main unit and transmitter. Low voltage will result in product failure.

3. No alarm sounds after a detection

   • a) Check if the low battery indicator is flashing
     (please replace the batteries immediately).

   • b) If the unit is armed and set to HOME mode and the PIR sensor detects an intrusion, the alarm will not sound. The PIR sensor is disabled in HOME mode. Check if the main unit is installed correctly.

Add a device to your existing alarm

We have created a 100% compatible alarm system to meet your needs. Here, we offer accessories that can work alone but also as a kit. This allows you
to personalise your alarm and to associate several accessories but also several alarms between them. For example, when a person triggers the opening detector, all your alarms will sound. You can deacti-vate your alarm using the code units, remote control or the remote keyboard.
More information on our website: https://chacon.com/fr/

Compatible products: 34035, 34038, 34043, 34044, 34045, 34046, 34048

Safety advice

• Don’t mix new and used batteries.
• Don’t mix alkaline, standard (zinc carbon) or rechargeable (ni-cad, ni-mh, etc.) batteries.
• Please use only the type of battery specified in the manual.
• Don’t leave used batteries lying around in the unit, as this may damage the unit.
• Incorrect use of the battery may damage nearby objects and result in fire or serious injury.
• Please keep batteries away from children. If you suspect that batteries have been ingested, seek medical attention immediately. Swallowing the battery can lead to serious consequences; internal burns within 2 hours or death.
• Recycle used batteries in accordance with envi-ronmental protection practices
• Don’t place the unit near a heat source, where it may be exposed to direct sunlight, rain or strong light.
• The unit is not waterproof. Don’t expose it to rain or immerse it in water.
• Don’t attempt to disassemble or repair the product yourself.
• Please keep this manual in a safe place.
• The reception distance may be affected if a strong interference signal exists in the area of use.

Technical specifications

• Easy to install
• Can be switched on or off remotely via remote control, remote keypad or code units
• Compatible products: 34035, 34038, 34043, 34044, 34045, 34046, 34048
• Battery: 1x CR2032 (included)
• Standby current: ≤ 3uA
• Alarm current: ≤ 15mA
• Box contents: 2x Door opener + battery (2x) + manual + fixing material

Support
www.chacon.com/support

• For indoor use only

This product must be treated in accordance with European Directive 2002/96/EC with the aim of being recycled or dismantled to minimise its impact on the environment. For further information, please contact your local or regional authorities.

Hereby, Chacon declares that the radio equipment type 34036 is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: www.chacon.com/conformity

Chacon S.A. – Avenue Mercator 2 1300 Wavre – BelgiumMade in PRC

References

• Downloads
• Boutique des produits Chacon et Dio
• Shop for Chacon and Dio products
• Downloads
• Contact us
• Chacon

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>