Chacon 34044 Alarm with Motion Detector User Manual
- June 9, 2024
- CHACON
Table of Contents
- Chacon 34044 Alarm with Motion Detector
- WHAT’S IN THE BOX
- OVERVIEW
- Introduction
- Linking the alarm with another product
- Wall installation of the control unit
- Reset pairing
- Add a device to your existing alarm
- Safety advice
- Technical specifications
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Chacon 34044 Alarm with Motion Detector
WHAT’S IN THE BOX
OVERVIEW
- Motion detector
- Speaker
- Flashing LED
- Pairing button
Introduction
Thank you for using this product.
- Please read all instructions carefully before using the product.
- Do not attempt to disassemble or repair the product yourself, as this will invalidate the warranty.
- In order to use this product, you must have either a remote control, a central unit with code or the remote keyboard. (Compatible references: 34035, 34036, 34038, 34043, 34045, 34046, 34048)
Battery installation: Central alarm unit with motion detector
- Using a crosshead screwdriver, remove the screw from the back of the motion detector.
- Slide the cover down to access the battery compartment.
- Insert the batteries, ensuring correct polarity (+/-).
- Close the compartment with the cover and screw.
Note: When the battery is low, the LED indicator will flash slowly (3s/flash)
Linking the alarm with another product
- Using a screwdriver, open the battery compartment of your alarm unit.
- Press and hold the learning button until you hear a «beep». The unit enters pairing mode.
- a. Remote control: Press any button. You will hear a «beep» sound to indicate successful pairing.
- b. Opening detector with or without code: Separate the two parts of the opening sensor to send a signal to the main unit. You will hear a «beep» sound to indicate successful coupling.
- c. Remote keypad: Press any button. You will hear a «beep» indicating successful pairing.
- d. Motion detector: with code: Wave your hand in front of the detector.
- To exit pairing mode, press and hold the learn button for 3 seconds. You will hear a double «beep».
NOTE: A maximum of 32 transmitters can be paired to a main unit.
Wall installation of the control unit
- Once you have installed the batteries, choose a location for your motion detector.
- Fix the bracket to the wall using the supplied dowels and screws.
- Fit the sensor onto the bracket and then choose the best angle for the sensor to have the best possible field of view.
Recommended installation height: Maximum 160cm and minimum 30cm.
NOTE : Adjust the installation angle so that it faces downwards.
Reset pairing
In order to reset your entire alarm, remove the batteries from your device. Then press and hold the learning button (see diagram point 1.). When you reinsert the batteries, you will hear two «beeps» indicating that the reset was successful.
Problem-solving
- False alarms from the main unit
- a) Check that there are no animals near the motion detector.
- b) In hot weather, moving shadows may also activate the alarm. Also ensure that the detector is not installed near a radiator or heat source.
- c) Check that there are no devices with strong electromagnetic fields near the door/window sensor. Strong electromagnetic fields can cause false alarms.
- The main unit doesn’t receive a signal from the transmitter
- a) Check if the pairing between the transmitter and the main unit was successful.
- b) If pairing was successful, check the battery voltage of the main unit and transmitter. Low voltage will result in product failure.
- No alarm sounds after a detection
- a) Check if the low battery indicator is flashing (please replace the batteries immediately).
b) If the unit is armed and set to HOME mode and the PIR sensor detects an intrusion, the alarm will not sound. The PIR sensor is disabled in HOME mode. Check if the main unit is installed correctly.
Add a device to your existing alarm
We have created a 100% compatible alarm system to meet your needs. Here, we offer accessories that can work alone but also as a kit. This allows you to personalize your alarm and to associate several accessories but also several alarms between them. For example, when a person triggers the opening detector, all your alarms will sound. You can deactivate your alarm using the code units, remote control, or the remote keyboard. More information on our website:https://chacon.com/fr/
Compatible products: 34035, 34036, 34038, 34043, 34045, 34046, 34048
Safety advice
- mix new and used batteries.
- mix alkaline, standard (zinc carbon) or rechargeable (ni-cad, ni-mh, etc.) batteries.
- Please use only the type of battery specified in the manual.
- leave used batteries lying around in the unit, as this may damage the unit.
- Incorrect use of the battery may damage nearby objects and result in fire or serious injury.
- Please keep batteries away from children. If you suspect that batteries have been ingested, seek medical attention immediately. Swallowing the battery can lead to serious consequences; internal burns within 2 hours or death.
- Recycle used batteries in accordance with environmental protection practices
- place the unit near a heat source, where it may be exposed to direct sunlight, rain or strong light.
- The unit is not waterproof. Don’t expose it to rain or immerse it in water.
- attempt to disassemble or repair the product yourself.
- Please keep this manual in a safe place.
- The reception distance may be affected if a strong interference signal exists in the area of use.
Technical specifications
-
Easy to install
-
Compatible products: 34035, 34036, 34038, 34043, 34045, 34046, 34048
-
Detection distance: 8 m (free field)
-
Detection angle: 100°
-
Alarm volume: 100 dB
-
Alarm Time: 30s
-
Standby current : ≤ 350uA
-
Alarm current: ≤ 150mA
-
Detector battery: 3x AA 1.5V (not included)
-
Box contents: Motion detector + manual
-
Supportwww.chacon.com/support
-
For indoor use only
-
This product must be treated in accordance with European Directive 2002/96/EC with the aim of being recycled or dismantled to minimize its impact on the environment. For further information, please contact your local or regional authorities.
-
Chacon S.A. – Avenue Mercator 2 – 1300 Wavre – Belgium Made in PRC
-
Registering the guarantee
-
To register your warranty, fill in the online form atwww.chacon.com/warranty
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>