TELTONIKA TeltoCharge Car Charging Station Instruction Manual

TELTONIKA TeltoCharge Car Charging Station

Instruction

• Dimensions without cable 170x341x97 mm
• Weight without cable 2.8 kg
• Operating temperature -30°C – +50°C
• IP rating IP55
• IK rating IK10
• Certification CE
• Standards 2014/35/EU, 2014/30/EU IEC 61851-1, IEC 61851-22

Electrical Specification

 AC INPUT SPECIFICATIONS

 | 7,4 kW| 11 kW| 22 kW
V     Input AC power connection| 1 phase| 3 phases| 3 phases
C     Input voltage| 220 to 240

VAC

| 380 to 415

VAC

| 380 to 415

VAC

D     Rated frequency| 50 / 60 Hz
E      Standby power consumption| 4 W
F      Earth (ground) fault protection| 30mA AC, 6 mA DC
G      Overvoltage category| CAT III
H     Protection against electric shock| Class I
AC output specifications
J      AC output voltage range| 220 – 240V AC| 380 – 415V AC| 380 – 415V AC
K     Connection standard| Type 2 cable
Type 2 socket

Part Number Structure

1 – 11 kW
2 – 22 kW
Connector| 0 – socket
1- Tethered cable
Connectivity| 0 – without GSM modem 1 – with GSM modem
 | P – grey
Front plate color| R – red M – blue B – white 0 – N/A
 | 1-|
| 2-|
Front finish| 3-
4-
5-|
 | 6-|
 |  | 0

Marking

Safety Warning

• A- Flying debris, risk of injury
• B- Risk of electric shock
• C Caution
• D- Sharp elements, risk of injurious cuts
• E-Special waste treatment

Required Tool

• A- Hammer
• B- Electric drill
• C-Pencil
• D-Screwdriver
• E- Cutting pliers
• F-Allen key 2,5 mm
• G-Measuring tape
• H-Utility knife 1-Level
• J-Drill bit 6

Including Part Number

• K-Wall plugs 6×35 mm
• L-Pan head self-tapping screws galvanized steel
• M-DIN912 M3x8 screws
• N-Cable gland
• O-Protective plugs

EV Charger Main Element

Connection

• A-SIM Card Slot
• B- Terminal block for AC input
• C-Ethernet connection

Install Process

DRILLING

• A-Place the drilling template on the wall (make sure it is horizontal using the level) and mark the three fixing points.
• B-Drill holes where the fixing points are marked.
• C-Insert the wall plugs into the fixing holes.

HOUSING INSTALLATION

• A-Fix the device on the wall by inserting the self-tapping screws (start with the top screw and make sure the housing is horizontal).
• B- Make sure the cable grommet is properly mounted on the cables (AC input cable and Ethernet cable).

Electric Wiring

• A-T/N single phase set up
• B-T/N three phase set up
• C-IT/TT three phase set up
• D-IT/TT single phase set up

SIM CARD INSTALLATION

• A- Inserta nano SIM card

CLOSING THE MIDDLE PANEL

• A-Place a middle panel on the housing
• B Fix it using DIN912 M3x8 screws

CLOSING THE FRONT PLATE

• A- Insert the upper part of the front plate to the fixing holes and fix the plate.
• B- Fix it using DIN912 M3x8 screws.
• C-Lock the top of the plate
• D-Lock the bottom of the plate
• E-Fix it using DIN912 M3x8 screws

CHARGER CONFIGURATION

• Step 1-Download the App
• Step 2-Connect using Bluetooth connection
• Step 3-Setup Maximum charging power
• Step 4-Setup other parameters
• Step 5- Pair end-user mobile device with TeltoCharge.

LED INDICATORS

• A- Yellow – LEDS pulsing – First start. Default settings have not changed.
• B-White – LEDS pulsing – Standby.
• C-Blue-LEDs light up from the middle Waiting for car to initiate charging.
• D- Blue- LEDS light up from top to bottom-Charging is scheduled. A schedule has been set by the user.
• E- Green-All LEDs are on- Charging is complete.
• F-Yellow- All LEDs are on Simplified charging sequence is denied, do not charge and contact your installer. G-Green – LEDs pulsing – Initialization of charging.
• H-Green – All LEDs light up from bottom to top – Charging is in process. 1- Red-LEDs pulsing – Faulty connection to car.

LED INDICATORS (ERRORS)

• A- Input voltage Error
• B- Output voltage or current fail
• C-Current leakage detected
• D- Connectivity Error E-Temperature Error
• F- Other Errors (not listed)

IN CASE OF ERROR: D error-check cable connection, disconnect it, inspect socket for damage or foreign objects and reconnect. A, B, C, or F errors- try to reboot your TeltoCharge device, if it does not help, make sure your power grid is not overloaded. A, B, C, F errors – if you already attempted step 1 and 2 and it did not work, contact your installer.

SAFETY AND MAINTENANCE INSTRUCTIONS

Installation, maintenance, and servicing of the charger must be done only by the personnel with relevant qualifications under the applicable local regulations. Unauthorized installation and modifications make the manufacturer’s warranty void. Do not use the charger if the enclosure or connector is cracked, opened, broken, or shows any other indication of damage. If the connector begins to melt or emits smoke, do not touch it. If possible, stop charging activities. Before opening the cover or cleaning the charger, power down the device. Do not use cleaning solvents on any part of the charger. Use a clean, dry cloth to remove dust and dirt. Do not open the cover in the rain. Use the Telto Charge charger under the operating parameters and within normal ambient conditions specified in the General and Electrical Specifications. Avoid installing the charger in a place that is under extreme weather conditions or is directly impacted by sunlight.

SIMPLIFIED EU DECLARATION OF CONFORMITY
Hereby, Teltonika Energy declares that TeltoCharge equipment is in compliance with Directive 2014/53/EU, Directive 2014/30/EU and Directive 2014/35/EU.

SAFETY RECOMMENDATIONS
Follow all the safety and installation instructions carefully. Failure to follow instructions may be a safety hazard and/or cause equipment malfunction. Any resulting damage due to disregard or actions contrary to the instructions in this manual is excluded from the product warranty.

CONNECTOR RECOMMENDATIONS AND INSTALLATION INSTRUCTIONS
Do not use if the charging cable is frayed, has broken insulation, or has any signs of damage or the vehicle plug or electrical outlet is dirty, wet, or damaged. Do not use the charging cable with a cable adaptor or an extension cable. Under any circumstances, do not tighten the charging cable while it is connected.

INSTALLATION INSTRUCTIONS
Ensure that the mounting surface can adequately support the weight of the charger and withstand mechanical forces associated with usage. The charger must be permanently connected to the electrical Earth of the installation. Do not install the charger in direct sunlight, or near flammable, explosive, or combustible materials, chemicals or solvents, gas pipes or steam outlets, radiators or batteries, and areas prone to flooding, high humidity and running water.

ELECTRICAL PROTECTION
The power supply line must be wired to an existing installation and be in accordance with local regulations.

DISPOSAL ADVICE
In accordance with the Directive 2012/19/ EC, at the end of its useful life, the product should not be disposed of as urban waste. It should be taken to a collection center or to a distributor that provides special and differentiated waste disposal.

LEGAL NOTICE
Any information in this manual may be changed without prior notice and does not represent any obligation on the part of the manufacturer. Images in this manual are for illustration purposes only and might differ from the delivered product.

www.teltonika-energy.com

References

• Teltonika Energy - IoT, Internet of Things

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>