GEORGE KOVACS P1558-66A-L Trizay 6-Light Black LED Pendant Light Instruction Manual
- June 13, 2024
- GEORGE KOVACS
Table of Contents
GEORGE KOVACS P1558-66A-L Trizay 6-Light Black LED Pendant Light
Product Information
- Product Model: Item#P1558-66A-L
- Revision Date: 05/09/2023
Product Usage Instructions
-
Preparation:
- Remove the fixture from the carton and ensure all parts are included.
- Shut off power at the circuit breaker and remove the old fixture along with the mounting hardware.
-
Mounting the Fixture:
-
Attach the mounting plate (A) to the outlet box using the provided mounting screws (B). Make sure the side of the mounting plate marked GND faces out.
-
Determine the desired hanging height and thread rods (F1, F2) to the coupling (E) on the top of the fixture body. Secure canopy (C) to rod (F1).
-
Pass the wires carefully through each rod and canopy. Tighten the rods and the canopy assembly until secured.
-
Adjusting the Arms:
Adjust the arms to the proper position as shown in Fig.3. -
Aligning and Securing the Bottom Frame:
-
Align the bottom frame to the bottom of the fixture body and secure it with screws (G).
-
Snap in the six decorative caps (H) to the bottom frame.
-
Attaching Support Cable:
The support cable is provided to support the weight of the fixture during wiring. Align the fixture to the mounting plate (A) and attach the hook (T) on the end of the support cable (P) into a slot located on the mounting plate (A). Carefully allow the support cable (P) to support the weight of the fixture during wiring. -
Connecting the Wires:
Connect the electrical wires as shown in Fig.2, ensuring thatall wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the provided green screw. After connecting the wires, tuck them carefully inside the outlet box. -
Finishing the Installation:
Align the canopy (C) over the mounting plate (A) and secure it with screws (D). -
Replacing LED Module:
The LED module can be replaced by a qualified electricianwithout cutting any wires or damaging any decorative elements. Refer to the installation steps and Fig.3 for detailed instructions.
INSTALLATION INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
WARNING ! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
PREPARATION
- Carefully remove the fixture from the carton and check that all parts are included as shown in the illustration.
- Shut off power at the circuit breaker and remove the old fixture including the mounting hardware.
MOUNTING THE FIXYURE (Fig. 1)
- Attach mounting plate (A) to the outlet box (not included) using mounting screws (B) (Size: #8-32N*L1”L) as shown in Fig.1. Note: The side of mounting plate (A) marked “GND” must face out.
- Determine the desired hanging height and thread rods (F1, F2) to the coupling (E) on the top of the fixture body. Secure canopy (C) to rod (F1). Pass the wires carefully through each rod and canopy. Then tighten the rods and the canopy assembly until secured.
- Adjust the arms to proper position as shown in Fig.3.
- Align the bottom frame to the bottom of fixture body and with screws
- (G) using screwdriver (not included). Snap in the six decorative caps
- (H) to the bottom frame.
- Place glass (K) onto fixture body, secure with metal caps (I) and screws (J).
- The support cable is provided to support the weight of the fixture while wiring. Align the fixture to mounting plate (A) and attach hook (T) on the end of support cable (P) into a slot located on mounting plate (A). Carefully allow support cable (P) to support the weight of the fixture while wiring (Fig.1).
CONNECTION THE WIRES (Fig. 2)
- Connect the electrical wires as shown in Fig.2, making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided. After wires are connected, tuck them carefully inside the outlet box.
FINISHING THE INSTALLATION (Fig. 3)
- Align canopy (C) over mounting plate (A). Secure with screws (D).
Replacing LED module (Fig.4)
The LED module can be replaced by a qualified electrician without cutting of wire and without damage to any decorative element to which the fixture is attached. See installation steps for more details ( Fig 3.)
- Shut off the power.
- Remove screws (D) and disconnect wire connectors and place fixture body on a clean surface. (Fig1)
- Remove screws (J) and metal caps (I) from the fixture body and remove glass (K).
- Press the button with printed ”L” quick connector on LED module (L) with screwdriver (not included) to disconnect the black wire and then disconnect the white wire from the printed ”N” quick connector on LED module (L). Carefully remove LED module (L) from the base.
- Reverse steps a-d for installing the new LED module.
Your installation is now complete. Return power to the outlet box and test the fixture.
Note : The illustration in figure 1 on this manual is for installation purposes only. It may or may not be identical to the fixture purchased. Dimmable with ELV and/or LED compatible wall dimmer switches.
P1558-66A-L
Item#P1558-66A-L (Rev. 05/09/2023)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>